XAS 375 JD6 Compressors Scott Ellinger Committed to sustainable productivity

Technical Specifications - XAS 375 JD6

Technical Specifications - XAS 375 JD6 (2)

Technical Specifications - XAS 375 JD6 (3)

Flow summary XAS 375 JD6

AIR SYSTEM INLET VALVE Spring loaded to the closed position Opened by inlet suction Closed by regulating pressure Also serves as check valve Unloading valve assembly part number 1604 0306 80 Unloading valve service kit part number 2911 0074 00

No-Load Condition Load Condition

Unload Condition Blow- Down Condition

REGULATING VALVE Regulating valve part number 1604 0847 85 Spring loaded Adjusting receiver pressure by changing spring tension to pressure gauge and loading valve to speed regulator to unloading valve Regulating pressure: Receiver pressure In order to regulate the pressure inside the reciever tank of our compressor, the air intake and the engine speed have to be controlled. This is done pneumatically. For that reason, we need regulating pressure. The regulating valve reduces the pressure inside the tank, thus providing the regulating pressure. This regulating pressure is then supplied to the unloader valve and the speed regulator or RPS. The air receiver pressure can be set to another value by adjusting the spring tension of the regulating valve. This is done by turning the handle on top the valve. Increasing the spring tension, by turning in, will increase the regulating pressure and consequently the pressure inside the vessel. Turning out will decrease the pressure. Regulating valve part number 1604 0847 85 Service kit part number 2911 0090 00

Oil separator Scavenge line Separator element Centrifugal separation Oil Separator filter element should be replaced Every 1,000 hours or yearly. Centrifugal separation Retainer should be checked and cleaned at time of separator element service Oil Air/Oil Separator element service kit part number 2911 0075 00

John Deere – Tier III – RPS in place of Pneumatic Speed Regulator Regulating Pressure Sensor or “Speed Sensor” p/n 1089 9579 80

AIR SYSTEM MINIMUM PRESSURE VALVE Maintains a minimum pressure of 58 PSI for oil flow Also contains the final check valve

Control Panel

XC 2002 Controller

XC2002 Controller Overview

XC 2002 Control Module

XC 2002 - Menus *Password is 2003* On newer units Parameters are under Extra Views. *Password is 2003*

XC 2002 Controller – 1.200 Program

XC 2002 Controller – 1.200 Program Automatically loads “with use of in line micro switch” Automatically unloads unit “unit will not reload” Service Timer 1 = 500hrs Service Timer 2 = 1000hrs “On” lets you connect to engine with machine not running

XC 2002 Controller – 1.200 Program

XC 2002 Controller – 1.200 Program

XC 2002 Controller – 1.200 Program

XC 2002 Controller – 1.200 Program – Unit Type 2

Event Logging

J1939 Canbus Engine Communication

J1939 Canbus Engine Communication . Cont

Engine Fault Code List

Engine Fault Code List

Engine Fault Code List

Engine Fault Code List

Engine Fault Code List

Engine Fault Code List

Engine Fault Code List

Engine Fault Code List

Engine Fault Code List

Displaying of J1939 DM1 Alarms

Wiring Schematic – XAS 375 JD6

Legend

Preheat Relay K1 Controlled by JDEC Starter Relay

Preventive Maintenance Filter Kits – XAS 375 JD6

Spare Parts Recommendation

Contact Numbers Main Number Atlas Copco Technical Support 1-800-732-6762 Option 3 Clayton Jones - Hurricane Boosters/Compressors - Supervisor 1-216-643-6802 direct & 1-317-681-4602 mobile Andrew Stevenson – Compressors: Low Pressure 1-720-479-2486 direct & 1-404-751-6717 mobile Will Hudson – Generators/Compressors 1-800-732-6762 Ext. 12920 & 1-832-454-8123 mobile Andrew Calendar – Compressors: High Pressure 1-720-479-2487 direct & 1-404-242-6203 mobile Jon Monaco - Hydraulic Att./Handheld Tools 1-800-732-6762 Ext. 12929 & 1-216-816-5008 mobile Brandon Dyer – Compressors: Low Pressure/Hydraulic Att. 1-216-643-6807 direct & 1-216-219-2290 mobile Scott Ellinger – Compressors 1-720-479-2476 direct & 1-720-375-1795 mobile

Committed to sustainable productivity.