LAB #8. Flywheel and Key Insert the flywheel key into the slot on the crankshaft then instert the flywheel.

Slides:

Advertisements

Similar presentations

#30 Ignition/Starter Switch #54 To Radio Fuse 1 Instrument Power Ignition Coil Red wire with bullet Long black wire with bullet. Wire was.

Advertisements

Ignition: Parts and Application Test

AS1 Setup IRIS Kansas City Workshop September 19-21, 2007 John Lahr (with Kay Wyatt) and portions from Seismology Instruction with AmaSeis By Tammy K.

Measuring and Testing Instruments

Small Gas Engine Ignition Systems

BumperBot uses two contact switches to go through a labyrinth. Bumper.

REMOVE AND INSTALL THERMOSTAT AND TEST OPERATION CS4 A.1 D.6 P-5/6.

Tools and Functions R7AxwS3BnU.

What is a fastener? A device to locate or hold parts

EE188L EE I Laboratory Lab #2 Resistive Circuits.

Here is the broken line. Step 5: Break loose encasing seal. With bar in vice as show, hit with hammer to break loose. Usually 2 or 3 hits will break loose.

Installation Instructions. Original distributor, coil, and plug wires.

Model 12 Intek Horizontal OHV

What is a fastener? A device to locate or hold parts.

Small Engine Parts Four-Cycle

PHSAUTOMOTIVESALSPHSAUTOMOTIVESALS SPARK PLUGS Thanks to NGK for picture.

Spark Plugs So little, but so important!. General info… Connected to the spark plug leads Ignite the air-fuel mix Are a consumable component Can be changed.

New Mexico FFA Agricultural Mechanics Career Development Event Engine Power.

Model 12 Intek Horizontal OHV Crankcase Disassembly and Assembly Lab #7.

Welcome to Autoescorts Please Press F5 to view & Press Enter to change Slides.

IGNITION SYSTEM SERVICE. TESTING AND REPAIR l Evaluate the symptoms –Narrow down possibilities l Pinpoint to a specific engine system –Compression –Fuel.

piston/connecting rod assembly

Systems of the Engine.

TORQUE WRENCHES & FEELER GAUGES WHAT IS TORQUE? TORQUE IS THE TURING OR TWISTING FORCE WHICH MAY OR MAY NOT RESULT IN MOTION.

Tagger and Vacuum Chamber Assembly Procedure. Preassembly of second bottom yokes and poleshoes. a) Install special support. b) Place the second bottom.

Small Engine Reassembly Briggs & Stratton OHV

Tool Identification Power Technology. Standard Screw Driver.

ALLEN & TORX WRENCHES NUT DRIVERS NUT DRIVERS SCREWDRIVER HANDLE WITH A SOCKET BUILT ON NOT MUCH TURNING POWER WORKS WELL FOR SMALL NUTS OR SCREWS THAT.

New Mexico FFA Agricultural Mechanics Career Development Event Engine Power.

Measuring Engine Components and Specifications

Replacing Spark Plugs Hua S. Wu English 393 December 10, 2009.

Unit A 6-3 Mechanical Systems and Technology. Problem Area 6 Agricultural Power Systems.

Model 12 Intek Horizontal OHV Carburetor Disassembly & Assembly Lab #3.

Small Engine Tools. Categories Small engine tools can be divided into three categories. 1.Mechanics tools 2.Measuring tools 3.Special tools.

Power and Energy 3201 Parts Catalog 206cc Briggs and Stratton 875 INTEK Series Engine Model: Tyler, Nathan, Zach and Jordan.

LAB #9 Valve Head replacement. Insert the valve. Make sure that the cap goes on the intake valve. Insert the springs. Insert the keeper.

LAB #7 Reassembly. Get Check Off Sheet Before you start, make sure you get a reassembly packet from Mrs. Winegar. If you do not have her check your work.

+ The Four Stroke Cycle By Elizabeth Fahey. + Outline Time Required: 1-3 classes Grades: 9-12 Background: Lesson is in conjunction with the small engine.

How to install an Xbox 360 By Michael Trim. Step 1 Position the Xbox where desired and then insert the ‘HDMI Cable/ Component Cable’ into the back of.

LAB #10. Governor Control Arm Using a 10mm socket install the two bolts that hold the governor control arm. Finger tighten then torque to 100 “#

Engine Reassembly Technicians need to take their time when reassembling an engine. This is not a race! Listen for instruction when to add the next piece.

Ignition and Electrical System Service Chapter #15.

Armature Air Gapping Engine Cooling Flywheel Armature Spark Plug Spark Plug Wire.

Model 12 Intek Horizontal OHV

LAB #2 CARBURETOR REMOVAL AND REPLACEMENT. Remove Cover Using a #10 star tip and a bit driver, remove the four screws to recoil cover.

Unit A 6-4 Mechanical Systems and Technology. Problem Area 6 Agricultural Power Systems.

Proper Use of Hand Tools. Wrenches Never use a pipe extension or “cheaters” Select the right opening for the nut Always pull the wrench handle when turning.

1 Flywheel 2 Connecting Rod 3 Valve 4 Primer 5. Timing Gear.

Auto Mechanics Tools Piston Ring Compressor.

1 Spark Plugs. 2 Spark Plugs ignite the air fuel mixture in the engine. ≈10,000 volts jump the gap between the center electrode & the ground electrode.

Engine Disassembly manual. Oil plugs/ 10 mm wrench.

1 Engine Mechanical Labs R. Bortignon. 2 Repair Information – essential! locate model number!

Small Engines Identification Small Engine Parts. 1. Sump or Crankcase.

Engine Technology Time the Ignition Some service procedures require removing the distributor from the engine. If the crankshaft is turned, the proper relationship.

Description of Hand Tools Tools help us do work and make things. Tools.

Small Engines/ Ag. 221 Ignition theory.

Annex 4 - Moving Frame and Whiffletree assembly

Assembly Instructions:

34 Chapter Small Engine Performance, Maintenance, and Troubleshooting.

Small Engine Disassembly

Ignition Timing R. Bortignon.

Ignition Systems Overview

Test the Ignition Coil of your Car With These 4 Steps

Ignition Timing R. Bortignon.

Agricultural Mechanics Career Development Event Engine Power

1 SCREWDRIVERS 3. PROPER USE OF HAND TOOLS B A

Disassembly and Assembly of A900C-W Electronic Governor Actuator for P8 Fuel Injection Pump

Educational Power Point by D&T Within Schools

Presentation transcript:

LAB #8

Flywheel and Key Insert the flywheel key into the slot on the crankshaft then instert the flywheel.

Flywheel Cont. Install plastic flywheel fins. Make sure it is in the correct position.

Flywheel Cup and Nut Insert the flywheel cup. Insert the flywheel Nut. Torque to 60 FOOT pounds of torque.

Tighten the Flywheel Break Using a pair of pliers connect the spring from the flywheel break.

Before install the armature CAREFULLY connect the wire on the back of the armature. Leaving the spark plug wire intact.

Ignition Coil Using a 10mm socket insert the bolt holding on the armature. We will torque it and set the gap when we put the second bolt in.