1 * * * Updated for NTS software version , * * *

2 Part 2b: Local Server Configuration and Set-up Note: All NTS logins are held by your local NTS administrator, contact them for the user names and passwords (anything labeled “Entry #1”, “Entry #2”, “Entry #3”, etc.)

3 Set Local Server NTS Software From the Desktop GUI (Graphic User Interface) Select Desktop is presented

4 Set Local Server NTS Software 1.Click NTS Setup Icon on Desktop to open Setup Screen below. (See previous slide) Go to step 8. Note: Steps 1 through 7 were already completed during the Software Download. Go to step 8.

5 2.Put in Entry #5 Set Local Server NTS Software 3.Select Set OIC Password 4.Select OK in the next pop-up. Note: A DOS screen may also pop-up temporarily but disappears. 5.Again, Select OK in the second pop- up

Select NTS 4 Local Server. 7.Write down IP address displayed. This is Local Server’s IP address and needs to be entered later during Workstation setup. Set Local Server NTS Software

7 9.Confirmation screen below displays. Select OK. 10.After selecting OK, select 8.Select Apply

8 11.If the screen above appears, Local Server is confirmed to be set up correctly. 12.Either reboot or log off to continue on to the operators mode. Set Local Server NTS Software

9 Setting Up Local Server Note: “Administrator” access required to perform this task. After laptop restarts… IF the screen below appears, AGAIN… THEN…

10 Setting Up Local Server Note: “Administrator” access required to perform this task. Next screen appears Press Enter on keyboard. Put Entry #3 for “user name” Put Entry #4 for “password”

11 Setting Up Local Server Note: “Administrator” access required to perform this task. 1.When “warning banner” appears, on keyboard, press and hold Shift then Enter. The NTS Log-in pops up. 2.Put Entry #1 for “user name” and Entry #2 for the “password” (get from NTS admin) 3. Select OK.

12 Setting Up Local Server Log off ntsadmin and re-attempt to continue on to the operators mode.Log off ntsadmin and re-attempt to continue on to the operators mode.

13 Operator Log-in 1.When “warning banner” appears, on keyboard, press Enter. The ETS Log-in pops up. Note: “Enter” is Operator’s Mode vs “Shift/Enter” is Admin Mode. 2.When ETS loads a.Put Entry #5 for “user ID” and Entry #6 for “password” b.Select Login

14 Configure Local Server Download Location Lists Data 1.Select NTS for applicable Program Mode. Connect phone and insert DMDC validated CAC Configure Server/Data Transfer page displays. Do not change any Data Transfer Settings unless explicitly directed by DMDC or Site Administrator. Note: “Operator” access required to perform this task.

15 Configure Local Server Download Location Lists Data 2.Select Download in Evacuation Section. 3.Download from Central Server message box appears. 4.Connect Modem. Note: See Modem Configuration Section on the following slides.

16 Initialize modem communications Configure Local Server Download Location Lists Data CCNFJ NTS Business Rule: Connect Modem to DMDC Central Server Select Click OK.

17 Configure Local Server Download Location Lists Data Connect Modem to DMDC Central Server The modem connection displays a dropdown list of available calling methods. Select appropriate method. Select Ensure this setting

18 Configure Local Server Download Location Lists Data Connect Modem to DMDC Central Server Select number with one of 3 methods below. If prefix required (i.e. 9 or 8) input in-front of listed number. Example: DSN: Commercial: Commercial Toll Free: DSN: , 01 or 02 Ensure 312 Typed inEnsure 312 Typed in Select Not RequiredNot Required

19 Configure Local Server Download Location Lists Data Connect Modem to DMDC Central Server Upon a successful connection, you will see the Modem icon at the lower right of your screen...then Connection may take a few moments

20 Configure Local Server Download Location Lists Data After selecting OK, a prompt to enter CAC PIN appears. Note: If blue/white progress indicator stays in motion for 30 seconds or more…and there’s no activity, press Alt+Tab to check for Java icon. This is a prompt to insert CAC or enter your PIN. On initial download attempts, or after computer re-started, this message ‘hides’ in background and user must click Alt+Tab to locate and bring forward. If not… press Alt Tab

21 Initialize modem communications Configure Local Server Download Location Lists Data Note: If communications already established… DO NOT check Initialize modem communications box. Then…ONLY Select OK

22 Configure Local Server Download Location Lists Data 5.Screen below displays a successful Evac Download. Each contains all ECC’s, Intermediate Safe Havens, and Repat Centers for specific NEO Event. 6.Select

23 Configure Local Server Download Location Lists Data 7.Select Evacuation Designation Label. to 8.Select Download in Location Section to download locations for Evacuation.

24 Initialize modem communications Configure Local Server Download Location Lists Data Note: After selecting Download from Location Section, the Download from Central Server message box MAY appear again. If communications are already established, DO NOT check Initialize modem communications box. Select OK

25 Configure Local Server Download Location Lists Data 9.Upon successful download, confirmation screen appears again. 10. Select 11.All locations listed for the Evacuation will display 12.Select location for local server then select Save

26 Configure Local Server Download Location Lists Data After saving location, Server configuration screen appears. Select

27 Configure Local Server Download Location Lists Data Note: Evac/Location download only required on Local Server computer. Registration computer “mirrors” Local Server’s location data, and picked up through secure wireless comms. 13.Select ECC or site’s location and click Save. Next screen appearing is the Welcome OIC screen. Local Server is now ready for operations.