© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 RIP version 1 Routing Protocols and Concepts – Chapter 5 Sandra Coleman,

Slides:



Advertisements
Similar presentations
Chapter 7 RIP version 2.
Advertisements

Routing Protocols and Concepts – Chapter 7 Modified by Tony Chen
RIP V1 W.lilakiatsakun.
RIP2 CCNA Exploration Semester 2 Chapter 7
RIP V2 W.lilakiatsakun.  RFC 2453 (obsoletes –RFC 1723 /1388)  Extension of RIP v1 (Classful routing protocol)  Classless routing protocol –VLSM is.
RIP V2 CCNP S1(5), Chapter 4.
© 2008 Cisco Systems, Inc. All rights reserved.Cisco ConfidentialPresentation_ID 1 Chapter 8: EIGRP Advanced Configurations and Troubleshooting Scaling.
Chapter 7 RIP Version 2 (RIPv2).
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 Static Routing Routing Protocols and Concepts – Chapter 2 Sandra Coleman,
Copyright 2008 Kenneth M. Chipps Ph.D. Cisco CCNA Exploration CCNA 2 Routing Protocols and Concepts Chapter 4 Distance Vector Routing Protocols.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public 1 Version 4.0 RIPv2 Routing Protocols and Concepts – Chapter 7.
Routing Protocols and Concepts – Chapter 7 Sandra Coleman, CCNA, CCAI
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public 1 Version 4.0 RIP version 1 Routing Protocols and Concepts – Chapter 5.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public 1 Version 4.0 RIP version 1 Routing Protocols and Concepts – Chapter 5.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 RIP version 1 Routing Protocols and Concepts – Chapter 5.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public 1 Version 4.0 Introduction to Dynamic Routing Protocol Routing Protocols and Concepts – Chapter.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public 1 Version 4.1 Routing Working at a Small-to-Medium Business or ISP – Chapter 6.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 Link-State Routing Protocols Routing Protocols and Concepts – Chapter.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 RIP version 1&2 Revised by Chakchai So-In, Ph.D.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public 1 Version 4.0 OSI Network Layer Network Fundamentals – Chapter 5 Sandra Coleman, CCNA, CCAI.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 Link-State Routing Protocols Routing Protocols and Concepts – Chapter.
Dynamic Routing Protocols  Function(s) of Dynamic Routing Protocols: – Dynamically share information between routers (Discover remote networks). – Automatically.
M. Menelaou CCNA2 DYNAMIC ROUTING. M. Menelaou DYNAMIC ROUTING Dynamic routing protocols can help simplify the life of a network administrator Routing.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 Distance Vector Routing Protocols Routing Protocols and Concepts –
Slide /2009COMM3380 Routing Algorithms Distance Vector Routing Each node knows the distance (=cost) to its directly connected neighbors A node sends.
© 2006 Cisco Systems, Inc. All rights reserved.Cisco Public 1 Version 4.0 Routing with a Distance Vector Protocol in an Enterprise Network Introducing.
Lecture Week 7 RIPv2 Routing Protocols and Concepts.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 Introduction to Dynamic Routing Protocol Routing Protocols and Concepts.
Introduction to Dynamic Routing Protocol
Routing -2 Dynamic Routing
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 Introduction to Routing and Packet Forwarding Routing Protocols and.
© Wiley Inc All Rights Reserved. CCNA: Cisco Certified Network Associate Study Guide CHAPTER 5: IP Routing.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 RIPv2 Routing Protocols and Concepts – Chapter 7.
Lecture Week 5 RIP version 1 Routing Protocols and Concepts.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 The Routing Table: A Closer Look Routing Protocols and Concepts – Chapter.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 Routing Protocols and Concepts Introduction to Dynamic Routing Protocol.
CCNA 2 Week 7 Distance Vector Routing. Copyright © 2005 University of Bolton Topics Distance Vector Protocol Issues RIP IGRP.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 Introduction to Dynamic Routing Protocol Routing Protocols and Concepts.
CCNA2-1 Chapter 5 RIP Version 1 (RIPv1). CCNA2-2 Chapter 5 Note for Instructors These presentations are the result of a collaboration among the instructors.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 Static Routing Routing Protocols and Concepts – Chapter 2.
1 7-Jan-16 S Ward Abingdon and Witney College Dynamic Routing CCNA Exploration Semester 2 Chapter 3.
Routing Protocols and Concepts – Chapter 7
RIP V1 W.lilakiatsakun. RIP V1 characteristics RIP is a distance vector routing protocol. RIP is a distance vector routing protocol. RIP uses hop count.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 RIP version 1 Routing Protocols and Concepts – Chapter 5 Modified by.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public 1 Version 4.0 Routing Protocols and Concepts Dr. Muazzam A. Khan.
1 © 2003, Cisco Systems, Inc. All rights reserved. CCNP 1 v3.0 Module 4 Routing Information Protocol version 2.
CCNA2-1 Chapter 5 RIP Version 1 (RIPv1). CCNA2-2 Chapter 5 RIP Version 1 RIPv1: Distance Vector, Classful Routing Protocol.
1 16-Mar-16 S Ward Abingdon and Witney College RIP v1 Routing CCNA Exploration Semester 2 Chapter 5.
Chapter 5 RIP version 1 CIS 82 Routing Protocols and Concepts Rick Graziani Cabrillo College Last Updated: 3/10/2008.
© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public 1 Version 4.1 Routing Working at a Small-to-Medium Business or ISP – Chapter 6.
1 © 2004, Cisco Systems, Inc. All rights reserved. Introduction to Classless Routing.
Routing Protocols and Concepts
Routing Information Protocol (RIP)
Introduction to Dynamic Routing Protocol
Chapter 3: Dynamic Routing
Chapter 3: Dynamic Routing
Introduction to Dynamic Routing Protocol
Chapter 3: Dynamic Routing
Routing Protocols and Concepts – Chapter 5
Chapter 5 RIP version 1 CIS 82 Routing Protocols and Concepts
Routing Protocols and Concepts
Chapter 2: Static Routing
Routing Protocols and Concepts – Chapter 5
Routing Protocols and Concepts – Chapter 5
Routing Protocols and Concepts – Chapter 7
Routing Protocols and Concepts – Chapter 5
Routing Protocols and Concepts – Chapter 7
RIP1.ppt CCNA Exploration Semester 2 Chapter 5
CCE1030 Computer Networking
CCE1030 Computer Networking
Presentation transcript:

© 2007 Cisco Systems, Inc. All rights reserved.Cisco Public ITE PC v4.0 Chapter 1 1 RIP version 1 Routing Protocols and Concepts – Chapter 5 Sandra Coleman, CCNA, CCAI

ITE PC v4.0 Chapter 1 2 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Objectives  Describe the functions, characteristics, and operation of the RIPv1 protocol.  Configure a device for using RIPv1.  Verify proper RIPv1 operation.  Describe how RIPv1 performs automatic summarization.  Configure, verify, and troubleshoot default routes propagated in a routed network implementing RIPv1.  Use recommended techniques to solve problems related to RIPv1  Turquoise text is test-worthy!

ITE PC v4.0 Chapter 1 3 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public RIPv1  RIP Characteristics -Oldest distance vector protocol -A classful, Distance Vector (DV) routing protocol -Metric = hop count -Routes with a hop count > 15 are unreachable -16 hops = infinity -Updates are broadcast every 30 seconds -Calculates metrics using the Bellman Ford algorithm -Data portion is encapsulated into UDP segment

ITE PC v4.0 Chapter 1 4 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public RIPv1  RIP Message Format  RIP header - divided into 3 fields -Command field -Version field -Must be zero  Route Entry - composed of 3 fields -Address family identifier -IP address -Metric (hops)  RIPv2 uses most of the ‘must be zero’ space

ITE PC v4.0 Chapter 1 5 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public RIPv1  RIP Operation –RIP uses 2 message types:  Request message -This is sent out on startup by each RIP enabled interface -Requests all RIP enabled neighbors to send routing table  Response message -Message sent to requesting router containing routing table

ITE PC v4.0 Chapter 1 6 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public RIPv1  IP addresses initially divided into classes -Class A -Class B -Class C  RIP is a classful routing protocol -Does not send subnet masks in routing updates -A router either uses the SM configure on the local interface or applies the default subnet mask of the class -Can’t support discontiguous networks or VLSM

ITE PC v4.0 Chapter 1 7 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public RIPv1  Administrative Distance –RIP’s default AD is 120 which makes it the least- preferred routing protocol (all others have a lower AD)

ITE PC v4.0 Chapter 1 8 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Basic RIPv1 Configuration  A typical topology suitable for use by RIPv1 includes: -Three router set up -No PCs attached to LANs -Use of 5 different IP subnets

ITE PC v4.0 Chapter 1 9 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Basic RIPv1 Configuration  Router RIP Command –To enable RIP enter: - Router rip at the global configuration prompt -Prompt will look like R1(config-router)# Notice that typing Router ? At the prompt Will show you ALL Available routing protocols

ITE PC v4.0 Chapter 1 10 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Removing RIP  To completely remove RIP routing from a router, just type in the following command: router(config)#no router rip  This command will STOP all rip processes and erase all existing RIP configurations!

ITE PC v4.0 Chapter 1 11 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Basic RIPv1 Configuration  Specifying Networks (You have to be able to do this on the test!) –Use the network command to: - Enable RIP on all interfaces that belong to this network -Advertise this network in RIP updates sent to other routers every 30 seconds -If you enter an IP address instead of a network address, RIP will include all interfaces in that CLASSFUL network in the routing process

ITE PC v4.0 Chapter 1 12 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Verification and Troubleshooting  To verify and troubleshoot routing - Use the following commands: -show ip route -show ip protocols -debug ip rip

ITE PC v4.0 Chapter 1 13 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Routing tables  You will have to look at a topology and pick from a list routes that would appear in a routing table for a specific router in that topology. One thing you really need to pay attention to is whether it is a connected or RIP route and look at the metric…make sure it is correct!

ITE PC v4.0 Chapter 1 14 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Verification and Troubleshooting  show ip protocols command -Displays routing protocol configured on router Be able to interpret these on a test!

ITE PC v4.0 Chapter 1 15 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Marking invalid routes Refer to the routing table below. Notice the timer SINCE the last update. How long would it take to mark INVALID if it went down? Invalid timer is 180 seconds. Subtract the time since the last update (5 seconds) and you get the answer! You will have to do this on the test as well!

ITE PC v4.0 Chapter 1 16 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Verification and Troubleshooting  Debug ip rip command (5.3.3 – online curriculum) -Used to display RIP routing updates as they are happening - USE undebug all to turn off ALL debugging!

ITE PC v4.0 Chapter 1 17 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Verification and Troubleshooting  Passive interface command -Used to prevent a router from sending updates through an interface - -Example: Router(config-router)#passive-interface interface-type interface-number Router(config-router)#passive-interface fa 0/0  When would you use this command? If you have an interface that has only END-USERS (LAN-Ethernet connection) connected, there is no need to broadcast routing updates to end-users. It WASTES bandwidth!  We only need to send routing update out interfaces where OTHER routers are found…but we do want the LANS to be included in the updates.  Passive interface prevents the transmission of routing updates through a router interface but still allows that network to be advertised to other routers

ITE PC v4.0 Chapter 1 18 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Verification and Troubleshooting  Passive interfaces

ITE PC v4.0 Chapter 1 19 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Automatic Summarization Modified Topology  The original scenario has been modified such that: Three classful networks are used: / / /24 The /16 network is subnetted into three subnets: / / /24 The following devices are part of the /16 classful network address: All interfaces on R1 S0/0/0 and Fa0/0 on R2

ITE PC v4.0 Chapter 1 20 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Automatic Summarization  Configuration Details -To remove the RIP routing process use the following command No router rip -To check the configuration use the following command Show run

ITE PC v4.0 Chapter 1 21 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Automatic Summarization  Boundary Routers –RIP automatically summarizes classful networks –Boundary routers summarize RIP subnets from one major network to another. –Because boundary routers summarize RIP subnets from one major network to the other, updates for the , and networks will automatically be summarized into when sent out R2's Serial 0/0/1 interface.

ITE PC v4.0 Chapter 1 22 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Automatic Summarization Processing RIP Updates  2 rules govern RIPv1 updates: -If a routing update and the interface it’s received on belong to the same network thenThe subnet mask of the interface is applied to the network in the routing update -If a routing update and the interface it’s received on belong to a different network then The classful subnet mask of the network is applied to the network in the routing update. RIPv1 DOES NOT send subnet mask information in its updates!

ITE PC v4.0 Chapter 1 23 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Automatic Summarization  Sending RIP Updates –RIP uses automatic summarization to reduce the size of a routing table.

ITE PC v4.0 Chapter 1 24 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Automatic Summarization  Advantages of automatic summarization: -The size of routing updates is reduced -Single routes are used to represent multiple routes which results in faster lookup in the routing table.

ITE PC v4.0 Chapter 1 25 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Automatic Summarization  Disadvantage of Automatic Summarization: -Does not support discontiguous networks

ITE PC v4.0 Chapter 1 26 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Automatic Summarization  Discontiguous Topologies do not converge with RIPv1  A router will only advertise major network addresses out interfaces that do not belong to the advertised route.

ITE PC v4.0 Chapter 1 27 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Default Route and RIPv1  Modified Topology: Scenario C  Default routes Packets that are not defined specifically in a routing table will go to the specified interface for the default route (AKA Gateway of last resort) Example: Customer routers use default routes to connect to an ISP router. Command used to configure a default route is ip route s0/0/1

ITE PC v4.0 Chapter 1 28 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Default Route and RIPv1

ITE PC v4.0 Chapter 1 29 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Default Route and RIPv1  Propagating the Default Route in RIPv1  Default-information originate command -This command is used to specify that the router is to originate default information, by propagating the static default route in RIP update. Indicates a ‘default – information originate’ command from R2

ITE PC v4.0 Chapter 1 30 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Where to put default routes?  Default routes ( ) and the ability to propagate these routes to others lies with the border router.  What is a border router? It is the router in your company that connects to your ISP.  So these commands belong on the border router! ip route s0/0/1 Default-information originate  You should NEVER exchange routing updates with an ISP. You only set up a static route to them. Otherwise, you end up with a HUGE routing table, and all outgoing traffic still goes there anyway!

ITE PC v4.0 Chapter 1 31 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Equal Cost Paths When you see routing table entries that have the same network listed with 2 different outgoing interfaces…know that these are 2 EQUAL COST PATHS.

ITE PC v4.0 Chapter 1 32 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Summary: Commands used by RIP CommandCommand’s purpose Rtr(config)#router ripEnables RIP routing process Rtr(config-router)#networkAssociates a network with a RIP routing process Rtr#debug ip ripused to view real time RIP routing updates Rtr(config-router)#passive-interface fa0/0Prevent RIP updates from going out an interface Rtr(config-router)#default-information originateUsed by RIP to propagate default routes Rtr#show ip protocolsUsed to display timers used by RIP

ITE PC v4.0 Chapter 1 33 © 2007 Cisco Systems, Inc. All rights reserved.Cisco Public Ch. 5 is OVER…Hallelujah! Study Guide – Packet tracer exercise 5-2 pg (homework) Labs – 5-1 (scenario A & B only) – In class today! If you don’t finish, Do scenario B on Packet Tracer for extra practice Online test for ch. 5 will be on until Sunday, Feb 24, midnight! Test on ch. 5 will be on Monday, Feb 25, 2013 We will do EVERYTHING we can in class today…anything left, is homework and should be done and ed to me before next Monday morning.