Firmware (CLP-310 Series)

Overview - I Model CLP-310 / CLP-310N / CLP-310W Print Method Multi-pass printing (Y->M->C->K) Printing Speed 4/16 ppm (Color/Mono) Resolution in print Best mode 2400 x 600 dpi Normal mode 1200 x 600 dpi Draft mode 600 x 600 dpi Duplex mode support Using Manual Duplex

Overview - II Supported I/O port USB (CLP-310) Network (CLP-310N) Network, Wireless LAN (CLP-310W) Memory Size CLP-310/CLP-310N : 32MBytes CLP-310W : 64Mbyte CRUM C/M/Y/K Toner : S-Chip2 Initial Toner Used only once without S-CRUM Included CLP-310 package, not for sale

Overview - III CPU Type : CHORUS3 (ARM 920T core) Speed : 360MHz Bus speed : 120MHz One chip solution (HPVC, I/O, JBIG, network …) Real-Time OS pSOS (V2.5) Driver SPLC

Overview - IV

Overview - V

ROM Image ROM image ROM release Boot image CLP-310 : 2Mbyte CLP-310N : 4MByte CLP-310W : 8Mbyte ROM release Boot image ROM image (without boot image) Boot + Rom Image

F/W Upgrade - I Three different ROMs (CLP-310/CLP-310N/CLP-310W) Network applications (SWAS, SWS) can be used for network port upgrade

F/W Upgrade - II F/W Upgrade using USB Port Make sure connecting Printer to the computer with a USB cable Upgrade in Ready mode Send ROM image file via USB cable in Ready mode Ex) Usblist2.exe CLP310N_V1.00.00.10.hd Upgrade in Special mode Power ON with pressing ‘STOP key’ Change Status LED to Orange color Quickly press ‘STOP key’ again Change status LED to Green Color  enable F/W upgrade at this time Send ROM image file via USB cable

F/W Upgrade - III F/W upgrade using SWS (SyncThru Web Service) Home -> Maintenance -> Firmware Upgrade 1 2 3 4

F/W Upgrade - IV 1. F/W upgrade using SWAS(SyncThru Web Admin Service) Home -> Maintenance -> Firmware Upload 1 2 3

F/W Upgrade - V 2. F/W upgrade using SWAS(SyncThru Web Admin Service) Home -> Maintenance -> Firmware Upload

F/W Upgrade - VI 2. F/W upgrade using SWAS(SyncThru Web Admin Service) Home -> Maintenance -> Firmware Upload

F/W Upgrade – VII 2. F/W upgrade using SWAS(SyncThru Web Admin Service) Home -> Maintenance -> Firmware Upgrade -> Upgrade 1 2 3 4

F/W Upgrade – VIII 2. F/W upgrade using SWAS(SyncThru Web Admin Service) Home -> Maintenance -> Firmware Upgrade -> Upgrade

F/W Upgrade – VIIII 2. F/W upgrade using SWAS(SyncThru Web Admin Service) Home -> Maintenance -> Firmware Upgrade -> Upgrade

F/W Upgrade – X 2. F/W upgrade using SWAS(SyncThru Web Admin Service) Home -> Maintenance -> Firmware Upgrade -> Upgrade

Information print Using Stop button

Setup in Status Monitor (SM) Power Save 5/10/15/20/30/45/60/120(minutes) Auto Continue If auto continue set to ON, Printer automatically paper out after 30 sec in paper mismatch state Altitude Normal / High 1 / High 2 / High 3 Engine F/W change voltage condition as altitude Color Color density

NVRAM NVRAM (or EEPROM) Non-Volatile RAM SPI (Serial port interface) Purpose To store Printer system and network configuration information Size CLP-310/CLP-310N : 8KBytes CLP-310W : 32Kbyte

Consumables Information Initial Toner Black : 1000 pages Color : 700 pages Regular Toner (for sale) Black : 1500 pages Color : 1000 pages Imaging Unit 24000 pages

Error List - I Display in Status Monitor window Consumables Life Errors Toner Low Toner Replace Toner empty Replace transfer belt soon Replace transfer belt Replace fuser soon Replace fuser Replace imaging unit soon Replace imaging unit Replace Pickup tray 1 roller Need to replace those items when replace error is indicated

Error List - II Invalid toner Invalid Yellow [Magenta/Cyan/Black] toner kit Mismatch Model Name, Supplier ID, Company Name, etc. Not install Yellow[M/C/K] Toner cartridge is not installed Service call error Fuser Low (Over) heat error LSU error Transfer belt error Dev. Home error Motor Lock error

Error - III Paper Paper Jam at the tray1 Paper Jam inside printer Paper Jam at the paper exit area -> Open cover and remove jammed paper Paper mismatch in the tray 1 Load specified paper in the tray 1

Error - IV Use Status Monitor (SM) Use Configuration Sheet to check set status to see occurred errors Use Configuration Sheet to check F/W version to check Consumables Problems

Q & A Thank You!!

Q1) Select the best way to check Error status. 1 1. Check Status Monitor 2. Check System Configuration Report 3. Check Network Configuration 4. Check Demo Page Q2) Select the best way to see Firmware version? 2 1. Demo Page 2. Configuration Sheet 3. Error Log 4. There is no way to see it. Q3) What is the best checking method When Consumables problems are occurred? 3 1. Print Error Log 2. Supplies Information 3. Configuration sheet 4. Demo Page