06.05.11 Scrumm meeting. Mechanical Done. Working on top part design Finished installing encoders Doing experiments on RFID tags What to do? Finish design.

Slides:



Advertisements
Similar presentations
MT Software Emulator Setup. 1. On the P Drive Here is the software 2. Create this folder in My Documents 3. Copy this.IMG File Into the folder 4. Execute.
Advertisements

Y A S O O B A L I b o r n o n 1 9 t h F e b r u a r y i n K a n p u r d i s t r i c t o f U t t a r P r a d e s h. H e s t a r t e d s i n g i.
Systems in Technology Objectives:  Define: system, component, troubleshooting, feedback, and automation  Draw and label an open and closed loop systems.
IR Object Detection living with the lab IR light from LED IR light reflected off object IR LED IR receiver Infrared (IR) light leaving an LED reflects.
Technology Processes 3 processes make a system Each processes is critical The sum is greater than the whole.
Capítulo 10 Instalaciones básicas programadas Instalaciones eléctricas interiores.
On Ubuntu Linux. Servers installed SSH APACHE First compiled from source Later installed again with apt-get PHP VNC (ubuntu) Had to be activated in system.
Includes division and multiplication Start. Q x
Engineering H193 - Team Project Gateway Engineering Education Coalition P. 1 Spring Quarter Week 6 Day 2 Lecture on and Examples of Electrical Circuits.
/t/ / I d/ /d/ Try Again Go on /t/ / I d/ /d/
Embedded Programming and Robotics Introduction and Overview Presented by John Cole Senior Lecturer in Computer Science The University of Texas at Dallas,
Assembly of Conductivity Flow Loop EAS 199B living with the lab (in preparation for calibrating conductivity sensor)
Image of Arduino. Arduino discussion Address issues with circuit walk-through – Electricity, Programming, Arduino Concepts Work on BeatTable (next week)
P14215 AUTONOMOUS WANDERING AMBASSADOR What is the project about? The objective of this project is to modify a currently remote controlled robot so that.
When you think of agriculture, what comes to mind?
A Bot With a Brain Using infrared obstacle detection circuits to create an autonomous robot that will navigate itself through an obstacle course. Bailey.
Parking Monitoring System Prepared by: Ali Al Misbah Salman Al-Belaihi Muneer Al-Hashem Mustafa Al-Qurain
Introduction and Wire Scanner Calibration BI-BL Students Meeting Aleksander Cudny Technical Student Warsaw University of Technology.
AN-NAJAH NATIONAL UNIVERSITY FACULTY OF ENGINEERING Supervisor: Dr. Nidal Farahat Prepared by: Iessa Asrawi Islam Barhoum Mahmoud Shreem Mohammad Ali.
Quadrotor Landing and Charging Justin Yim. Uses Aerial sensor platform Monitoring Surveillance Exploration Image from:
JULLIENOR TITAS DAS EEL 5666 – IMDL FALL /2/2014.
Troubleshooting Brian Kidney Engr September 22, 2003.
Engineering & Design Small Learning Community.
Feeder Version UP from the file in the Installation Disc Serial Number Current System Version.
A Snack Food Launching Robot: THE BORDOM DESTORYER! Presented by Jessica Mylynne Shaw.
Juan David Rios IMDL FALL 2012 Dr. Eric M. Schwartz – A. Antonio Arroyo September 18/2012.
MARK WILSON UNIVERSITY OF JOHANNESBURG DEPARTMENT OF ELECTRICAL AND ELECTRONIC ENGINEERING STUDY LEADER – PROF. FRANCOIS DU PLESSIS.
Final Presentation SETH NYDAM IMDL DR. ARROYO AND SCHWARTZ.
Scrum meeting. Mechanical Done. Finish the final design. Ordered all the material for the final frame. What to do? Work on the final model.
Scrumm meeting. Mechanical Done. Built a prototype. What to do? Build a casing for the hard drive test.
Radio Frequency Identification (RFID)
Scrumm meeting. Mechanical Done. Tire vs belt? Tire chosen. What to do? Do a prototype of a car. Continue with design.
WARM UP 10/20/15 1.Your Warm Up should be glued into your notebook immediately! 2.DO NOT TOUCH any of the materials at your table. If you do, you may lose.
Scrumm meeting. Mechanical Done. Are building system for tires What to do? Continue with building Build casing for hard drive.
Team 19 Project Br ö sel. Team Members 2/9 The Project Design Alternatives Testing Future Work Questions Team Members Nathan Leduc Electrical/Computer.
Scrumm meeting. Mechanical Done. Worked on final type What to do? Finish the assembly of the bottom part.
This trademark does not associate with the company
Scrum meeting. Mechanical Done. Cut material in sizes, ready for assembly the frame. Build a prototype for the rim. The belts, barings and gears.
Scrumm meeting. Mechanical Done. Designed the top part Working on encoders Working on documentation What to do? Work on the top part Finish encoders.
Scrumm meeting. Mechanical Done. Work on RFID attachments Started designing top Working on encoders What to do? Work on design encoders.
Hello there. Smiley, Smasher, and myself will be assisting you as we learn how to wire a mechanical relay circuit. When you are finished with this lesson.
Generators, Motors, Transformers
Scrumm meeting. Mechanical Done. Having a problem to fit motors to tires and are working on it. What to do? Same as above.
IR Object Detection living with the lab IR light from LED IR light reflected off object IR LED IR receiver Infrared (IR) light leaving an LED reflects.
RoverBot Assembly The following pages show assembly plans for the RoverBot using the Consumer MindStorms or School Team Challenge Lego kit. Assemble the.
Image from
ME 120: Arduino Programming Arduino Programming Part 1 ME 120 Mechanical and Materials Engineering Portland State University
Team 4: The Beancounters Kyle Haver Ethan Price Wesley Tso Shicheng Guo SOFTWARE DESIGN NARRATIVE.
Electrical and Solar Installation - dynamic-integration.com
WARM UP You MUST have your IAN Notebooks Today!!!
8/30/2004 RoverBot Assembly The following pages show assembly plans for the RoverBot using the Consumer MindStorms or School Team Challenge Lego kit. Assemble.
Electrical Circuits.
Scrum meeting.
Progress Report Chester Liu 2013/7/26.
Scrum meeting.
Internet of Things.
Remote Controlled Smart Socket
Arduino Basics Rajeev Dwivedi, PhD.
Physics 4 – Jan 24, 2017 P3 Challenge –
Quicken Installation Problem Number More info :
WELCOME.
What is Arduino? By James Tedder.
FeMaidens Programming
Project Renovatio Joshua Fraser Alastair Fraser Ruofei Fu Chao Jiang
Sensory perception with Arduino
Welcome.
Chapter 1 Introduction of Arduino
ELECTRICAL CIRCUITS AND CONSTRUCTIONS An electrical circuit is a network consisting of a closed loop, giving a return path for the current 2.
All About Serial.

Presentation transcript:

Scrumm meeting

Mechanical Done. Working on top part design Finished installing encoders Doing experiments on RFID tags What to do? Finish design Prepare top part

Electrical Done. Encoders and IR sensor wiring Got wifi entena Making a circuit bracket Arduino What to do? Technical documentation Finish bracket

Sensor Done. Got videos from Alcan Image processing What to do? Work on the new images

Software Done. PID Encoders Initialization script What to do? Try to do a loop in sólin

Feedback: Privacy Policy Feedback
Do Not Sell My Personal Information
About project: SlidePlayer Terms of Service

© 2025 SlidePlayer.com. Inc. All rights reserved.