IPC-D-325 8.4 Special Assembly Drawing Notes

Slides:

Advertisements

Similar presentations

3 Title Blocks and Part Lists Permission granted to reproduce for educational use only. Describe drawing sheet sizes and formats Identify marginal information.

Advertisements

UVM CricketSat Assembly Manual. Getting Started Make a hard copy print out of the following page It will help you identify the proper components Place.

Single-Balanced Mixer Assembly Instructions Revision 2 Updated 5/7/2012.

CricketSat Receiver Assembly Instructions This is the instruction slides for the assembly of a receiver board. It would be a good idea to review soldering.

ASE Flip-Chip Build-up Substrate Design Rules

Computer Tools and kits for Computer troubleshooting

Engineering Drawings & Measurements

Feature-Based Modeling and Optional Advanced Modeling

Datums and Datum Feature References

CricketSat LP (Transmitter) Assembly Instructions This is the instruction slides for the assembly of a transmitter board. This is the board that will fly.

First Article Inspection Report

1 Detecting fake materials Key clues. 2 Fraudulent box Labeling mistakes A missing icon could mean the label is fake, but the 0335 date code on a brand.

EET 450 – Advanced Digital Printers, Plotters and other hard copy output devices.

S Changes and Procedures

GLAST LAT ProjectTEM &TEM-PS Manufacturing Readiness Review – September 16, 2004 GLAST Large Area Telescope: Performance & Safety Assurance Pat Lujan TEM.

LSU 06/04/2007Electronics 21 Electronic Components Electronics Unit, Lecture 2 Identification of components and handling precautions to protect them from.

Graphs of the Linear Function: Graphing Calculator TI-84 Plus

Ch 17 communicating solutions 1.Alphabet of lines- technical lines used in multi-view drawings.

© 2015 Desco Industries Inc. StaticControl.com ESD Control Experts HBM vs. CDM vs. CBE What is the difference?

Handling Marking Depaneling Screen Printing Final Assembly Solder Wave Unloading Lift.

1 3/22/2004 Allegro Free Viewer 15.0  Installation Download from bd/downloads/allegroviewers/index.aspx

Chapter 4: Hypertext Markup Language Primer TECH Prof. Jeff Cheng.

RESISTOR A. Open your Titlebox

Electronic Components 1Department of ECE/EEE. 2 Introduction An electronic component is a basic electronic element usually packaged in a discrete form.

LSU 09/12/2013Electronics - SkeeterSat1 Building SkeeterSat Inventory Components  Identify components Use the parts list and assembly manual  Tape to.

Agriscience Toolbox Plan of Procedure 1. Table Saw (equipment) Rip the bottom of the toolbox to a width of 10 inches.

IPC Datum Features Datum features indicate the origin of a dimensional relationship between a toleranced feature and a designated feature or.

IPod analyses Paul, Ethan, Niels. Casing: Plastic cover Dual injection molding ▫White cover ▫Transparant layer on top of this Advantages ▫Lower part cost.

Graphic boclair academy TOLERANCES.

Front, Top, Side Holes & Curves Isometric. Technical Drawing: the practice or skill of portraying objects in a precise way using certain techniques. Technical.

IPC In-Circuit Test Fixtures In-circuit test fixtures are commonly called bed-of-nails fixtures. A bed-of- nails fixture is a device with.

CE 303: Introduction to Construction Blueprint Lab.

IPC Mounting Over Conductive Areas Metal-cased components shall be mounted insulated from adjacent electrically conductive elements. Insulation.

IPC-D-325 Table 4-1 Typical Master Drawing Documentation Requirements

Dept. of Information & Communications Technology Circuit Diagram and Prototype Construction (Project 1) slide L1-1 Objectives v How to read schematic Diagrams.

ASSEMBLING THE PCB Have the PCB in front of you as shown. Make sure there are no copper tracks showing. This side is called the component side.

Tooling Holes1 Tooling holes are non-plated holes with very tight tolerances to prevent movement between the tooling pins and the board. Tooling holes.

Tutorial: Mechanic – electrician Topic: Electronics II. class Operational Amplifiers: Integrator Prepared by: Ing. Jaroslav Bernkopf AVOP-ELEKTRO-Ber-006.

LSU 08/11/2004Electronics 41 Assembly Techniques Electronics Unit – Lecture 4 Component Preparation Component Placement and Soldering Inspection Activity.

Working Drawings Stephen W. Crown Ph.D.. Working Drawings A final set of drawings providing all the details and information needed to manufacture and.

GLAST LAT ProjectFebruary 10, 2004 R. Johnson Tracker MCM Production Readiness Review 1 LAT QA has hired a full-time on-site representative (Donald Knaepple)

The printed circuit board (PCB) design §PCB design is part of the design process of a product in electronics industry. §PCB is a piece of insulating plastic.

911Shield Initial APP Download. 911Shield Initial Setup Screen  Once the App is installed on your device it will require setup information as shown on.

UNDERSTANDING COMPUTERS From the Beginning: History of the Computer.

ADVANCED MECHANICAL DRAFTING

Any bright gets attention. This is the reason why projectors have long been popular as a medium of instruction. The lighted screen is a silent shout-

8.1 hardware devices Output devices By Ranjit Bassi.

Kursus “electronic assemblies & SOLDERING Technique”

ELECTRONIC ASSEMBLIES AND SOLDERING TECHNIQUE –PART II

Nets and Drawings for Visualizing Geometry

Robot Electronics.

Introduction to Arduino Microcontrollers

ASSEMBLING THE TIMER Have the PCB in front of you as shown. Make sure there are no copper tracks showing. This side is called the component side.

Mechanical Dimensions

GRAPHING CALCULATOR Part 2

BRIAN KLATT MISSION ASSURANCE MANAGER

Capacitor Assembly K. McFarlane 9/30/02 9/30/2002 TRT meeting Oct 2002

Welding Representation

1. New Assembly 2. If Top Plate is on the list, double-click on it.

Break down Lance rack Cut one of each of these for each rack

Are the buildings below three dimensional shapes?

CS-401 Computer Architecture & Assembly Language Programming

Pictorial Markings.

Performance Specifications

Mechanical Dimensions

IPC Compliance Testing (DPA) Methodology

Presentation transcript:

IPC-D-325 8.4 Special Assembly Drawing Notes Assembly drawings may contain a special set of notes as needed. The following notes are typical: 1. Workmanship to be equal to and compliant with the requirements of IPC-A-610. 2. Mark group (or dash) number, revision and serial number as shown; marking to be 0.10"-high characters using item no. 6, white epoxy ink, per MIL-I-43553, type II.

IPC-D-325 8.4 Special Assembly Drawing Notes 3. This assembly contains electrostatic discharge (ESD) sensitive devices; static-free handling is required per MIL-STD-1686, class 2.

IPC-D-325 8.4 Special Assembly Drawing Notes 4. Conformal coating is not required. 5. Designations are for reference only and do not appear on individual parts. 6. Dimensions shown specify maximum envelope limits for the finished assembly.

IPC-D-325 8.4 Special Assembly Drawing Notes 7. Orientation of polarized capacitors is denoted by a plus (+) sign. Polarity is identified on the part. 8. Dot identifies pin #1 location and device orientation when viewed from the top. 9. Using solder paste screen, apply solder paste, item #4, to primary side of board.

IPC-D-325 8.6 Separate Parts Lists Example: Assembly Drawing Number 8745139, Revision A. Parts List Number PL 8745139, Revision A.