Porewater temperature is 40°C Specify domain’s starting fluid temperature on the Initial pane.

Slides:

Advertisements

Similar presentations

INRNE-BAS MELCOR Pre -Test Calculation of Boil-off test at Quench facility 11th International QUENCH Workshop Forschungszentrum Karlsruhe (FZK), October.

Advertisements

Institute of Energy and Sustainable Development Improvement of a Two-Dimensional (2D) Borehole Heat Exchanger (BHE) Model Miaomiao He, Simon Rees, Li Shao.

Author: Cliff B. Davis Evaluation of Fluid Conduction and Mixing Within a Subassembly of the Actinide Burner Test Reactor.

122 Nov GTK Microchannel Cooling Hydraulic simulation with Rectangular Manifold Enrico Da Riva, Vinod Rao CERN (EN/CV/DC) 22 th Nov 2011 E. Da Riva,

Simulation lasts 30 years Aquifer is 70% Quartz Specify domain’s starting fluid composition on the Initial pane Initial fluid in equilibrium with Quartz.

Chemstations, Inc – Houston, TX – – An Overview of Process Simulation What is needed? What are the steps?

MuCool Absorber Review meeting FermiLab, Chicago 21 – 22 February 2003 Fluid Flow and Convective Heat Transfer Modelling by Wing Lau & Stephanie Yang Oxford.

SECTION 3 CHANGES IN TEMPERATURE AND PHASE Chapter 10.

Convection Convection: transfer of heat by a flowing liquid or gas

Explain why the heat flow for a home is different in the winter vs. the summer.

The governing equation for groundwater flow can be written using total head (h) or pressure (p). Why do we typically use head (h) as the dependent variable?

CONVECTION: THE TRANSFER OF THERMAL ENERGY BY THE MOVEMENT OF THE PARTICLES FROM ONE PART OF A MATERIAL TO ANOTHER; TRANSFER OF THERMAL ENERGY IN A FLUID.

EGEE 520: Spring 2008 Instructor: Dr. Derek Elsworth By: Sylvain-Didier Kouame A Study of Fluid displacement in Porous Medium using Nitrogen/CO2 injection.

The oven given in the figure is heated with a heat source having the heat flow rate Q. The total heat capacity of all objects in the oven is C and the.

Clean water Start and end times of two reaction intervals Specify domain’s starting fluid composition on the Initial pane.

Numerical simulation of the Alum lakes geothermal outflow J. Newson and M. J. O’Sullivan.

X1t models reactive transport in groundwater flows in one linear or radial coordinate. Set initial fluid composition and mass of sorbing mineral Fe(OH)

Thermal Conductivity. Influence of Fluid Velocity on the Longitudinal Thermal Dispersivity of a Porous Medium.

ICP 12/4/12 Heat and Temperature Notes Video: Classroom Video: Methods of Heat Transfer.

Applied Geothermics Aachen 0ct Numerical Simulation of a Thermal Response Test (TRT) Experiment R. Wagner Applied Geophysics, Aachen University.

Specify domain’s starting fluid temperature on the Initial pane Porewater temperature is 40 °C.

Heat Transfer. Heat is the transfer of thermal energy between substances that are at different temperatures.

In Class Examples CME 370: Heat & Mass Transfer Spring

Chapter 17.3 How do buoyancy and Archimedes’ principle relate to fluids?

Initial chemical composition and temperature can vary across the domain. Click on a “+” button to enter heterogeneity data for any field variable: ● enter.

Conduction C ontents: Basic Concept Example Whiteboards.

Decouple reaction between carbonate and Benzene(aq), other forms of carbon. Config → Redox Couples… Default setting: all redox reactions are coupled.

O o Problem HOMEWORK-01 Establish the closed loop block diagram. G c (s)=K p Answer: The oven shown in the figure is heated with a source having.

AME Int. Heat Trans. D. B. Go 1 Different Coordinate Systems cartesian cylindrical spherical.

Moving Thermal Energy. CONDUCTION ► Is the transfer of energy through matter by direct contact of particles.

Microwave Cooking Modeling Heat and moisture transport Andriy Rychahivskyy.

MULTLAB FEM-UNICAMP UNICAMP Workshop on Thermal Boundary Conditions Several thermal boundary conditions will be explored in this workshop modifying the.

Variable inlet chemistry. Inlet fluid “contaminated” enters the domain from t = 0 to 2 years Inlet fluid “flush” enters the domain from t = 2 to 10 years.

Basic concepts of heat transfer

Pulse of Benzene contaminated water is attenuated by biodegradation. X1t models reactive transport in groundwater flows in one linear, radial, or spherical.

Standards 3: Thermal Energy How Heat Moves  How heat energy transfers through solid.  By direct contact from HOT objects to COLD objects.

* Materials that allow heat, electricity, or sound waves to pass through them.

Decouple reaction between carbonate and acetate, carbonate and methane, and sulfate and sulfide. Config → Redox Couples… Default setting: all redox reactions.

Clean water Specify starting fluid composition on the Initial pane.

Conduction Convection Radiation

Specify coordinate system on the Domain pane.

Chain together kinetic reactions

14-6 Heat Transfer: Conduction

SAMPLE PROBLEM MATRA Input Preparation

o Problem Qoven Obtain the closed loop control diagram. Gc(s)=Kp

Date of download: 12/27/2017 Copyright © ASME. All rights reserved.

Plate Heat Exchanger (PHE)

Physics 202 Lecture 4 Heat and Temperature.

Specify domain’s starting fluid composition on the Initial pane

Specify domain’s starting fluid composition on the Initial pane

Specify domain’s starting fluid composition on the Initial pane

Specify domain’s starting fluid composition on the Initial pane

X position (m) I s o t p i c m n C , d a y Bulk fluid CO (aq)

The Intervals pane sets the total duration of the simulation.

The Initial fluid has negligible Pb2+ everywhere but the central node

Earth’s Energy Balance

Specify domain’s starting fluid composition on the Initial pane

Reading Materials: Chapter 9

Default setting: all redox reactions are coupled.

Config → Dual Porosity… Run → Go

Chapter Four: Energy transfer by Heat, Work and Mass

Energy Transfer Through Heat

Temperature Is a property of an object which determines the direction of net heat flow when an object is placed in contact with some other object. Heat.

Segment 1: Chapter 2 Mader

Heat Temperature Conduction Convection Radiation

12. Heat Exchangers Chemical engineering 170.

PANDA Collaboration Meeting

The Sun is the source of energy for the Earth.

Presentation transcript:

Porewater temperature is 40°C Specify domain’s starting fluid temperature on the Initial pane

A single inlet fluid named “flood” flows into the domain for 20 days. Define the reaction intervals. Specify what fluids flow into the domain, and when.

A 200°C injectate will displace the initial fluid The inlet fluid is defined on the Fluids pane

Specify domain size and gridding on the Domain pane. Domain is 2000 cm long, divided into 40 nodal blocks Radial domain set in this example

Specify flowrate on the Flow pane. Injection pressure 0.7 atm greater than formation pressure

Set various thermal properties on the Medium pane. Can include transient heat sources or sinks within the domain. Set thermal conductivity of porous medium to model heat conduction. Run → Go traces the model Set heat capacity of the fluid and rock to simulate heat transfer by advecting groundwater.

Hot water is injected into the domain’s inlet. Heat transported by advection and conduction.