RELAY. Relay A relay is an electically operated switch. Many relays use an electromagnet to operate a switching mechanism mechanically, but other operating.

Slides:

Advertisements

Similar presentations

IO Interfaces and Bus Standards. Interface circuits Consists of the cktry required to connect an i/o device to a computer. On one side we have data bus.

Advertisements

10 Ways to Ruin Your Mini-Max microcontroller (and lose $69)

Week10 Boolean Instructions on the Boolean Instructions  Boolean (or Bit) addressable capability is unique to the 8051  Enables efficient handling.

Automatic Transfer Switch using microcontroller

NAND-gate Latch. Summary NAND-gate Latch The time sequence at right shows the conditions under which the set and reset inputs cause a state change, and.

Lecture 51 The Telephone System. Lecture 52 The Telephone System The modern telephone system draws from these Electrical Engineering subdisciplines: Signal.

CLASSIFICATION OF COMPUTER

ELECTRICAL. Circuits Outline Power Hub Microcontroller Sensor Inputs Motor Driver.

ECE 265 – LECTURE 13 Interface to switches and LEDs 7/3/ ECE265.

THYRISTORS WHAT ARE THYRISTORS ?.

Programmable Logic Controller Internal Operations

GCSE Electronic Products

Submitted By Ravi Raj Rajeev Kumar Vipul Batra. FUNCTIONS PERFORMED BY THE RELAY MADE 1.OVER VOLTAGE PROTECTION 2.OVERCURRENT PROTECTION.

RM2C Understanding Connections on the Robot Control Board (RCB).

The Microcomputer System In this presentation you will: Investigate the microprocessor Title Page.

Industrial Machine Control

MR. KERINS Logic Gates- Electrical Engineering. LOGIC GATES Logic gates are primarily implemented using diodes or transistors acting as electronic switches,

CS 1308 – Computer Literacy and the Internet. It’s Not Magic  The goal of the next series of lectures is to show you exactly how a computer works. 

1LAKSHMI.B.E.. Full step -clock 2LAKSHMI.B.E. Full step –anti clock 3LAKSHMI.B.E.

Star I Controller Input/Output Numbering on Controller and MIRO Devices.

Microcontroller based system design Asst. Prof. Dr. Alper ŞİŞMAN.

Teachers Name : Suman Sarker Telecommunication Technology Subject Name : Microcontroller & Embedded System Subject Code : 6871 Semester : 7th Department.

MOBILE OPERATING ROBOT ON EMBEDDED SYSTEM

ELECTROMAGNETIC RELAY By: Engr.Irshad Rahim Memon.

ElectromagnetsResearchElectromagnetsResearchElectromagnetsResearchElectromagnetsResearch.

Multiplexers 1 The output is equal to one of several input signals to the circuit The multiplexer selects which input signal to use as an output signal.

PLCs were invented in answer to the needs of the automobile industry, and were introduced in the late 1960’s. They were designed to take the place of older,

Electrical Control Components

PROGRAMMABLE LOGIC CONTROLLER (PLC) AND AUTOMATION

Electronic Circuit Diagrams

AUP2G57 configured as flip flop Dual Configurable Logic Design Contest.

Electromagnetism Introduction.

A four function ALU A 00 ADD B MUX SUB 11 Result AND OR

CS 1308 – Computer Literacy and the Internet Building the CPU.

Chapter 10 Flip-Flops and Registers 1. Objectives You should be able to: Explain the internal circuit operation of S-R and gated S-R flip-flops. Explain.

DPCL Solid State Device Discrete Control Lecture.

2nd session of R&A Transistors & couplers. Agenda T ransistors as switch. T ransistor testing. O pt couplers. R elays. S imulation with Proteus 7 professional.

Figure 10.1 Cross-NOR S-R flip-flop: (a) Set condition; (b) Reset condition.

PRESENTATION ON THE TOPIC By: Rahul agarwal. INTRODUCTION  Overload protection circuit are required in inverters and uninterrupted power supplies to.

1 Electrical Fundamentals We need some understanding of electrical fundamentals to do the lab exercises. Electric Circuit Consists of: –Power Source: Battery,

AND Gate Inputs Output Input A (Switch) Input B (Switch) Output Y (Lamp) 0 (Open) 0 (OFF) A B Lamp.

What we will do today: Introduce the new topic on Electronic Components. Identify the three main parts of any electronic system. Give examples of output.

Opto Couplers Types And Its Applications. Opto Couplers Types And Its Applications Introduction:  A lot of electronic equipment.

Self Switching Power Supply. Introduction Self Switching Power Supply  Embedded system requires a regulated power supply.

MICROCONTROLLER INTERFACING WITH STEPPER MOTOR MADE BY: Pruthvirajsinh Jadeja ( ) COLLEGE:DIET BRANCH:EC.

How do ABI test Digital ICs?. Test principles ABI digital tests are designed to find faults on boards. To do this the following principles are used: Confirm.

Simple Water Level Controller Circuit with Microcontroller and Alarm.

Chapter 36 Combinational Logic Circuits. Objectives After completing this chapter, you will be able to: –Describe the functions of encoders, decoders,

A PRESENTATION ON RELAY, OPTOISOLATOR AND STEPPER MOTOR INTERFACING WITH AVR Prepared By:- Katariya Prakash[ ] Kathiriya Shalin[ ]

Embedded Systems Programming (What they do and when / how to use them)

Dept. of Electrical and Computer Eng., NCTU

Arduino Based Industrial appliances control system by decoding dual tone multi frequency signals on GSM / CDMA network. Submitted by:

Topics to be discussed Transmission line Type of connections

ARINC Real-time protocol translation A project for Icelandair

Different Types of Relays.

Principles & Applications and Simple Interfacing

Sharif University of Technology Department of Computer Engineering

Hasib Hasan Ankit Baingane Edward Hanson

EE345: Introduction to Microcontrollers Memory

The CASCADE Method similar to that for electromechanical devices.

The Zero-plus [0+] Sensor with Actionable Signal

Input > Process > Output

University of Maryland Baltimore County Department of Computer Science and Electrical Engineering CMPE 212 Laboratory (Discussion 10) Hasib Hasan

Counter Integrated Circuits (I.C.s)

I/O Experiments Assignment 1.

Presentation transcript:

RELAY

Relay A relay is an electically operated switch. Many relays use an electromagnet to operate a switching mechanism mechanically, but other operating principles are also used. Relays are used where it is necessary to control a circuit by a low-power signal (with complete electrical isolation between control and controlled circuits), or where several circuits must be controlled by one signal. The first relays were used in long distance telegraph circuits, repeating the signal coming in from one circuit and re-transmitting it to another. Relays were used extensively in telephone exchanges and early computers to perform logical operations.

Types of Relay Latching Relay Reed Relay Contactor Polarised Relay Solid State Relay

Working with the Relay As it’s a switch, it has some pin configuration also. No. of pins decide the operation of inputs and outputs. We are using Relay of 5 Pins. Which is used offcourse for swiching purpose. Provide a sufficient amount of current to this relay, an extra circuit is also require because microcontroller is not capable of providing such current, that’s why ULN2803 IC is used for this purpose.

ULN2803 IC pin Configuration

Continue... Input of this IC is connected with the the controler’s ouput. Output of this IC directly goes to the Relay to operate it. Therefore, any Electical device of 220V, 100W can be controlled.