Power System 9-36V -12V -5V -3.3V -2.5V -1.8V -1.2V Vin Distribution.

Slides:



Advertisements
Similar presentations
Operational Amplifiers
Advertisements

Biomedical Instrumentation I
1 Electronic Circuits OP AMPs. 2 Electronic Circuits Operational amplifiers are convenient building blocks that can be used to build amplifiers and filters.
Scott Starks, PhD, PE Department of Electrical & Computer Engineering UTEP.
Revision analog electronics
Capstone Fall 2005 GFX-One Guitar Processor Team Carpal Tunnel September 8, 2005.
Environmental Management. Environmental Needs Maintain internal temp within operating temp of components Optics: 10 Mp cameras » -40 < 0 < 70 Electronics.
EEG Machine By The All-American Boys Featuring Slo- Mo Motaz Alturayef Shawn Arni Adam Bierman Jon Ohman.
V Input V Output Kelvin Monitor Points Input power +12 volts Output / Test Load Carrier Board Plug In Card ASIC Chips Load Keep Short Leads Cable Yale.
Control & Monitoring of DC-DC Buck Converters Satish Dhawan Yale University Power Distribution Working Group Meeting- Tuesday 24 February 2009 ATLAS Upgrade.
Use Ohm’s Law to solve the following equations.
COMP 364 Prof Jess UEAB 2006 Power Supplies and UPS.
Solar Powered Battery Charger
Operational Amplifier based Charge Amplifiers
Tower Light Show Power Supply Team Members: Jesse Walson Jake Wagner Dave Miller Sponsor: Robert Rinker Team Advisor: Touraj Assefi.
MSP 430 Project ECE 300 Spring 2004 William S. McLemore Ruben D. Briano Cheng-Han Tsai.
Amplifiers: From Ideal to Real Why amplify? Gain = Vout / Vin = sensitivity Ideal Op Amp Negative gain summation amplifier Positive gain for increased.
Lecture # 12&13 SWITCHING-MODE POWER SUPPLIES
Power Management for Embedded Systems. Power requirement for Embedded Micro Systems Multiple supply voltages Small size in all components, L R C etc High.
Electronics - Revision 2. In electronics, it is the voltage that is important. Draw voltage time graphs for analogue and digital systems. 3. Draw a block.
LDO Regulator John O’Hollaren. StandardQuasi-LDOLDO High Dropout Stability not a problem Medium Dropout Stability a concern Low Dropout Stability is a.
LDO Regulator John O’Hollaren. StandardQuasi-LDOLDO High Dropout Stability not a problem Medium Dropout Stability a concern Low Dropout Stability is a.
System Spec Goals My LDOTexas Instruments TLV1171 Minimum Drop Out1.0 V0.455 V Required Capacitance1 pF1 μF Pos. Settling Time10 nano sec~ 5 μ sec Neg.
Hybrid Aggregates aka “Flash Pools”. What is is An Aggregate comprised of HDs&SSDs Dedicated ssd read & write cache/buffer Fast. ;) Available in 8.1.
ELCT 201 Lab Op Amp ON/OFF Control (use Schematic in your Front Panel)
Design of Digital-to-Analog Converter Qin Chen Yong Wang Dept. of Electrical Engineering Mar. 14th, 2006 EE597G Presentation:
Complex Circuits Notes Series Circuit + Parallel Circuit = Complex Circuit.
Senior Design II Midterm Presentation September 29, 2009.
Portable Rechargeable Output Power Supply (PROPS) Final Presentation April 24, 2008.
Students: Thomas Carley Luke Ketcham Brendan Zimmer Advisors: Dr. Woonki Na Dr. Brian Huggins Bradley University Department Of Electrical Engineering 2/28/12.
Chapter 22 Electrical Systems. Textbook page 169, 171.
Lianna Dicke MOTOR HARDWARE BREAKDOWN. Design Goals: Drive DC motor that draws 5 A maximum continuous current Voltage operation at 12 Volts (automotive)
Low Cost Universal Test Equipment Survey on Power supplies.
Chapter 6.3 Notes Electrical Power. Voltage causes charges to move in circuits. This movement creates work. How fast the charge does work is called Power.
Minimum Price $100. Minimum Price $45 Minimum Price $40.
UOP ECT 246 Week 3 iLab Op - Amps Check this A+ tutorial guideline at For more classes.
The Ideal Op-amp (Operational amplifier) v+ VOUT v– +15V VIN VOUT –15V
How can we measure it? This is what a basic circuit looks like:
4. Operational Amplifiers
Each Stage Efficiency = 0.8 Overall Efficiency = 0.64
Stefano Levorato INFN Trieste
Example #6 Buck Converter with Simplorer
SUMMING AMPLIFIER INTEGRATOR DIFFERENTIATOR COMPARATOR
EEE2135 Digital Logic Design Chapter 1. Introduction
Chapter 27 Power Supplies.
The open loop gain of this op-amp is 105 and the bandwidth is 10 Hz
Project Block Diagram Transmitter Receiver × 2 Input Device Protection
UNIT-5 Design of CMOS Op Amps.
Switching DC Power Supplies
Examples of Negative Feedback Applications: A) Inverting Amplifiers
Behavior of DC/DC converter at power off(not TI device)
Presentation P2 System Design Preliminary Detailed Design
Xilinx Reference Design Test Report
6.0 Voltage Regulators.
MALVINO Electronic PRINCIPLES SIXTH EDITION.
Introduction to Linear Voltage Regulators
The operational amplifier
Sample & Hold Circuits CSE598A/EE597G Spring 2006
Inductive Sensor Analysis
Team 70: Air Guitar Gloves
XTR111 Vout or Iout Analysis
Op Amps and Voltage Dividers
Differentiator and Integrator Circuit
ADC and DAC Data Converter
Inductive Sensor Analysis
10k 20k Vin Vout H3 What is the gain?
Linear Technology Corporation
ADC and DAC Data Converter
Budget *Cost divided evenly between Fuel Cell and Fly Wheel Groups.
Group 9 Andrew White Ryan Hamdorff Jimmy Psihogios
Presentation transcript:

Power System 9-36V -12V -5V -3.3V -2.5V -1.8V -1.2V Vin Distribution

Power Requirements of Devices Voltage Line (Volts) DSP (Amps) FPGA (Amps) SATA (Amps) DDR2 (Amps) INS (Amps) Cameras (Amps) SPI (Amps) Total Current/Voltage (Amps) TBD Total Current/Device (Amps) MAX POWER= W

Chip Selection Process Buck Converter Selection WeightLTM4612LT3500LTC1624LTC1876L4964LM34910SDBD9702TPM6681ATRTLE6389GVLT3433 Vin Vout Iout Op Temp #Outputs Price Type Complexity Total

Chip Selection Process (cont.) Monitor Selection WeightLTC2938LTC2930LTC2932MB3771Max16063 Vsupply Applications Op Temp Price RESET Options Total

Power Flow Diagram

Power Block Diagram

Power Schematic -Single Regulator -Vout = 1.19*(1 + R2/R1)

Simulation Results

Analysis

Risk Assessment

Hard Drive Selection Process WeightToshiba SSDMicron SSDSamsung SSD Max Seq. Rd Max Seq. Wr SSD Type3444 Total