1. Lab 5: Model Making: Polyhedron IAT 106 Spatial Thinking and Communication.

Slides:



Advertisements
Similar presentations
PAPER HOUSES Create a 3D House or Cabin.
Advertisements

Drafting – Product Design & Architecture
Engineering Design GE121 Isometric and Orthographic Sketching
How to solve missing view problems and other mysteries of 3D worlds
MECHANICAL DRAWING MULTIVIEW DRAWINGS.
Lecture 4 – Part 2 Introduction to SolidWorks
Design Intent: Effectively using Constraints in SolidWorks
From Isometric Drawings to Plans and Elevations
Plan for today (27 Jan 2015, Lecture 4)
Descriptive Geometry:
Multiview Projection. Basics of Projections  Orthographic drawings are the result of projecting the image of a three-dimensional object onto one of six.
Engineering H191 Engineering Fundamentals and Laboratory I
Orthographic to Isometric
 An artwork that is created, when geometric lines are measured and spaced out so that they will produce a design that is either drawn or sewn. These.
MECHANICAL DRAWING.
Solids and Views A solid is in 3D. But we can only draw in 2D.... So how can we draw a solid?
Grid Objectives 1.On the page that has your image, copy this objective: You will use measuring skills in order to draw a 1-inch grid. 2.On your drawing.
ENTC 1110 OBLIQUE PICTORIALS.
Technical Graphic Communication
Nets and Drawing for Visualizing Geometry
Orthographic Drawings
DRAFTING THE UNIVERSAL LANGUAGE SKETCHING Rough Sketches are the most common recording method. The term “rough” describes the state of the design ideas.
Planning Considerations in planning are: –Function or Usefulness: is it needed? –Kind of Wood: Depends on function and finish used. –Size & Proportion:
Sketching & Drawing Projects
Chapter 4 Sketching and Orthographic Projection. 2 Links for Chapter 4 Sketching Shapes Sketching Procedures Orthographic Projection.
Multiview Drawing A multiview drawing is one that shows two or more two-dimensional views of a three- dimensional object. Multiview drawings provide the.
Foundations of Technology Sketching and Technical Drawing
Communication Technology
Multiview Sketching Multiview Sketching
Chapter 6 – Pictorial Sketching
Two-Variable Data On the coordinate plane, plot points with given coordinates, and determine the coordinates of plotted points. Represent a two-variable.
Nets and Drawings for Visualizing Geometry
Multiview Drawings. Multiview Drawing A multiview drawing is one that shows two or more two-dimensional views of a three- dimensional object. Multiview.
SANTANA DRAFTING MULTIVIEWS 1 An introduction Mr. Fitzgerald Rm
TA 101: Technical Arts II Dr. Prishati Raychowdhury Department of Civil Engineering IIT Kanpur Office: FB 336; Phone: 6692
Multi-View Sketching. Learning Objectives Understand using the ‘Glass Box’ to help define orthographic projections. Be able to define Multi-View Drawing,
Career & Technical Education Sketching Explain and demonstrate basic sketching skills and techniques.
Building Boxes What is the largest volume open top box that you can build from an 8 ½ by 11 inch sheet of paper?
Funded by a grant from the National Science Foundation. Any opinions, findings, conclusions or recommendations expressed are those of the authors and do.
Project #1: Sign Development Name: Date: Project Checklist  Pro Desktop  Power Miter Box  Scroll Saw  Band Saw  Drill Press  Belt Sander  Disc Sander.
Which is best Isometric view
Graphical Language Basic Lines and Projections Scales Cross-Sectional Views and Sections.
Section 1.1 Nets and Drawings for Visualizing Geometry
Orthographic Drawings
Section 1.1 – Nets and Drawings for Visualizing Geometry
Nets and Drawings for Visualizing Geometry
Filling and Wrapping 1.2 Making Rectangular Boxes
Multiview Sketching & Projection Chapter 5 Print handouts
Orthographic Drawings
Multiview Sketching Multiview Sketching
Orthographic Projection
Shape and One Point Perspective Project
Orthographic Projection
Multiview Sketching Multiview Sketching
Isometric Projection -the term ‘isometric’ comes from the Greek for ‘equal measure’ reflecting the scale along each axis is the same - Isometric views.
Geometry Three Dimensions
Orthographic Projection
Orthographic Projection
Orthographic Projection
Workshop Practice E102A Isometric and Orthographic drawings
Multiview Projection.
Orthographic Projection of Inclined and Curved Surfaces
Multiview drawings.
Multiview Sketching Multiview Sketching
Forging new generations of engineers
Basic Lines and Projections Scales Cross-Sectional Views and Sections
S1 Orthographic Sketching
2-D Representations of Solids
Projections & Technical Drawing
AUXILIARY VIEWS C H A P T E R E I G H T.
Presentation transcript:

1. Lab 5: Model Making: Polyhedron IAT 106 Spatial Thinking and Communication

IAT106 Spatial Thinking and Communicating Why are We Doing this Project? Model making is fun! Besides that … In this lab you explore the relationship between 3 approaches to representing your ideas and see how each helps the others, and collectively how they assist you to improve your spatial thinking and communicating skills. You will be given a simple isometric view of an object and, in teams of 2: 1. (30 min) Sketch a full multiview drawing of the object 2. (45 min) Build a Physical Model of the object 3. (30 min) Build a digital—SolidWorks--model of the object.

IAT106 Spatial Thinking and Communicating You will make: 1.Multiview drawings 2.Physical model 3.SolidWorks model 4.Report We provide 1.Isometric paper 2.Cardboard 3.Cutting board 4.Glue 5.Masking tape What & How You provide 1.Teams of 2 2.Pencil 3.Metal ruler 4.X-acto knife or box cutter 5.Spatial Thinking power

Making the Polyhedron Steps: Step 1: Sketch 6 orthographic views from the isometric view Step 2: Transfer the orthographic views to cardboard (use pins to locate points). Cut the faces of your model from the cardboard. Fabricate your physical model, using parts you just cut and tape/glue. Verify the physical model against the primary orthographic views Step 3: Make a digital model of the same object using SolidWorks. Step 4: Answer reflective questions relating to this project Deliverables 6-view+inclined face multiview drawing Cardboard model of polyhedron SolidWorks model of polyhedron Word document with answers

Step I: Sketching the Object (1/2) Layout of the 6 views (6 principal orthographic projections): Note: Place views so they fit on the 11X17 inch grid paper. There is room for ONLY 1 grid unit between views! Your polyhedron has an inclined face: you will have to sketch this in addition to the 6 principal views. You will have to determine which of the principal views shows the width and which the length of this face! sketch 6 ortho views of polyhedron shown in the isometric drawing your TA supplies Use Gridded 11x17 inch sketching paper (TA supplies)

IAT106 Spatial Thinking and Communicating Step I: Sketching the Object (2/2) Establish the scale: For this exercise, use three squares on the grid paper for one square of the isometric drawing. Front View: OrthographicFront View: Isometric =

IAT106 Spatial Thinking and Communicating Step II: Building the Cardboard Model (45 min) After drawing the six views: –Align and Tape the grid paper directly on top of the cardboard (put tape along top edge to allow for lifting later) –Using thumb tacks, press into the grid paper at all of the vertices to make a small hole in the cardboard. –Flip the paper up and connect the dots (tack holes) to transfer the sketch onto the cardboard. –Cut the cardboard with knife and ruler. NB! Keep the paper: it will be needed in the marking process! Also, if you make a mistake, you’ll need to redo one or more faces!

IAT106 Spatial Thinking and Communicating Step II: Building the Card Model assemble the model using the faces you cut from the cardboard, using the scotch or masking tape, or glue. Be careful with gaps and rough cuts:-) These photos are from Fall 2012, where we used CardStock instead of cardboard.

IAT106 Spatial Thinking and Communicating Step II: Building the Card Model: Fall 2013 and Spring 2014 used Cardboard Various problems and small mistakes are shown Cardboard is thicker than cardstock! So thickness needed to be accounted for.

IAT106 Spatial Thinking and Communicating Step II: Building the Card Model: Allowing for Material thickness Task: build 6” x 3” x 4” box out of 1” thick material: 3” When we actually build the box, we must allow for the thickness of the material 4” 6” 1” thick Box Idealized: “Outline” suggests walls are zero thickness. So vertical “ends” are 3” high. Are they? What should be the dimension of the ends? Height = 3” – 2 x thickness = 1” (!) Material

IAT106 Spatial Thinking and Communicating Step II: Building the Card Model: Allowing for thickness of material What other ways might we join top and side? Butt joint with equal ‘shortening’ on all pieces. Strong, but shows “inside” of material. Partial cut and fold. Easy, but ugly. Mitre joint. Difficult but nicest looking. Two 45 deg cuts needed!

Allowing for Material Thickness B C L A L – 2t To make a cube of side “L”, only 2 of the 6 faces will be a full “L” in size! L L L t A B C L L – 2t

IAT106 Spatial Thinking and Communicating Step III: Building the SolidWorks Model Remember the usual method: 1.The polyhedron is just a SolidWorks “Part”; parts are collections of features, starting with a Base feature. 2.Shape Features are created using a 2D sketch that you extrude into 3D (boss extrude, cut extrude, etc.). Save the file and submit through Canvas as usual. Note: you probably will NOT have time to complete this in the lab; Complete this as Homework and submit to Canvas before the start of next week’s lab..

IAT106 Spatial Thinking and Communicating Step IV: Reflecting on the Representations This is to be done by each person, individually, on their own. Write short but thoughtful, considered answers for each question and submit your answers as a Word document through Canvas before the start of next week’s lab. 1.How did the sketches help with a) making the cardboard model and b) the Solid Works model? 2.If you could change the order, what would this be and why? 3.Describe how you resolved the “inclined” face.

Overall Process Flow Sketch 6-view Multiview drawing on 11 x 17 grid paper 30 min Deliverable: Drawing Due: In Lab 1 Make Physical model: - transfer sketch to cardboard - cut pieces - tape pieces together 45 min Deliverable: cardboard mode Due: In Lab 2 Make SolidWorks Model - use sketch – extrude method 3 40 min Deliverable: SolidWorks model Due before next lab 4 Review/Analysis Questions -answer the 3 “reflective” questions about your process Homework Deliverable: Word document Due: before next lab 11” x 17” grid paper 11” x 17” cardboard