1 Chapter 2: Direct Link Networks (Part Two) Dr. Rocky K. C. Chang 30 January 2004

2 1. Automatic repeat request (ARQ) Approach to achieving link reliability: –Ask for retransmission when a corrupted frame is detected. Mechanisms for asking a sender to retransmit: –Receiver to send negative acknowledgments for corrupted frames, or –Receiver to send positive acknowledgments for good frames. –Which one is better?

3 1. Automatic repeat request (ARQ) Both approach require a timeout mechanism. –Negative-ack approach: A timer starts when a negative acknowledgment is sent out. –Positive-ack approach: A timer starts when a message is sent out. Retransmissions take place when timeouts occur: –Negative-ack approach: The receiver retransmits a negative acknowledgment. –Positive-ack approach: The sender retransmits a frame.

4 1. Automatic repeat request (ARQ) The ARQ implements a positive acknowledg- ment approach. –Only after an acknowledgment is received will a frame be removed from a send buffer. –An acknowledgment can be piggybacked on a message sent to the other direction. –An acknowledgment sometimes indicates the sequence number of the next expected frame. –Positive acknowledgment is usually accumulative, e.g., receiving an acknowledgment for frame 4 implies that frames 1-3 are all received correctly.

5 1.1 Stop-and-wait ARQ The maximum number of unacknowledged frames is one. –A sender cannot send a second frame before receiving an acknowledgment for the first frame. The minimum number of sequence numbers needed to identify the frames is two (0, 1), i.e., the first two in the send buffer. –0: for the frame sent and waiting for its acknowledgment. –1: for the frame to be sent after receiving an acknowledgment for the 0th frame.

6

7 1.1 Stop-and-wait ARQ Advantages: –Very simple to implement, both on the sender and receiver sides. Disadvantages: –Achieve a very low throughput, especially in a high-speed link (does not keep the pipe full). –In the best case, only one frame can be sent in a round-trip time. –In other cases, an additional number of round-trip times is required when errors occur.

8 1.2 Sliding-window (or go-back-n) ARQ The maximum number of unacknowledged frames may be more than one. –A sender may continue to transmit frames even when acknowledgments for frames previously sent are not received. –A sliding window is used to keep track of the sender’s state and receiver’s state. –The window size determines the maximum number of unacknowledged frames allowed on the sender side.

9 1.2 Sliding-window (or go-back-n) ARQ On the sender side: –Frames are labeled by a sequence number of integer values, starting from 1. –A static parameter: send window size (SWS) –Two variable parameters: The maximum sequence number being acknowledged by the receiver (LAR) The maximum sequence number sent by the sender (LFS) –Note that LFS  LAR LFS = LAR: All frames sent have been acknowledged. LFS > LAR: LFS  LAR frames are yet to be acknowledged.

Sliding-window (or go-back-n) ARQ –Also note that LFS  SWS + LAR. When LFS = SWS + LAR, the window is said to be full, and no more new frames can be sent before (LAR+1)th frame is acknowledged. –How do the values of LFS and LAR change? LFS is initialized to 0, and it is incremented after each new frame is sent. LAR is initialized to 0, and it is shifted to the right according to the new sequence number(s) acknowledged by the receiver.

Sliding-window (or go-back-n) ARQ Sender side: Receiver side: = SWS LAR LFS ……  RWS NFE ……

Sliding-window (or go-back-n) ARQ On the receiver side: –A static parameter: receive window size (RWS) RWS is the maximum number of out-of-order frames that the receiver is willing to accept. –A variable parameter: Sequence number of the next frame expected (NFE) –If a frame, whose sequence number is larger than NFE+RWS, is received, the frame will be discarded; otherwise, it will be buffered in a receive buffer. –When a frame is received correctly, NFE is either updated or unchanged.

Three uses of ARQs Provide reliable service Provide in-order service –The original order of the frames is preserved even when out-of-order frames are received. Provide flow control –Prevent the sender from flooding the receiver. –The sender needs to vary the value of SWS by taking into account of the state of the receive buffer.

14 2. Local area networks (LANs) Early 1980s –IBM’s token ring vs. DIX (Digital, Intel, and Xerox) Ethernet –IEEE (logical link control), (Ethernet), (Token Bus), (Token Ring) Late 1980s –Fiber Distributed Data Interface (FDDI) –Distributed Queue Dual Bus (DQDB) Early 1990s –ATM LANs vs Fast Ethernet (switched Ethernet)

15 2. Local area networks (LANs) Mid-1990s –IEEE (wireless LAN) Now and future (who knows?) –Gigabit Ethernet vs ATM LANs –Optical Ethernet, wireless Ethernet Development trends: –From shared medium to switched LANs –From router-based backbone to switched backbone –From wired to wireless –From single-medium to multi-media

Ethernet LAN: physical connectivity Components: –Cable (passive) –Transceivers (transmitter + receiver) –Adaptor (active). Each adaptor card is uniquely identified by a 48-bit (physical or MAC) address, e.g., 00:40:26:5A:67:88. Design principles: –Cost-effective resource sharing –Reliability –Inexpensive

Ethernet LAN: physical connectivity Adaptor Transceiver Host Ethernet cable

Ethernet LAN: physical connectivity Both DIX and IEEE Ethernets do not require switching elements. –Hosts are connected to a cable (10base2/5/T) through network adaptors. –Several segments may be connected (horizontally) to another segment (vertically) through hubs, which serve as repeaters.

Ethernet LAN: physical connectivity Repeater Host … … … …

Ethernet LAN: physical connectivity from the datalink layer and up

Ethernet LAN: Datalink sublayers A new multiple access control (MAC) problem: –How do multiple hosts share a single transmission medium efficiently? –This problem occurs in token ring, FDDI, and wireless LAN. –An additional MAC sublayer was created for this purpose. A logical link control (LCC) sublayer: –Provide similar services as a datalink layer except that error detection is provided at the MAC sublayer.

Ethernet LAN: Datalink sublayers –Provide three types of services: Unacknowledged connectionless (datagram) service: Basically no additional service. Acknowledged connectionless service: Reliability through a stop-and-wait-ARQ-like mechanism. Connection-mode service: A connection is set up between two hosts with flow control and reliability services.

Ethernet LAN: Datalink sublayers The datalink layer consists of –LLC sublayer and MAC sublayer IEEE Logical Link Control (LLC) Sublayer IEEE 802.3IEEE 802.4IEEE ANSI FDDI IEEE IEEE

Ethernet LAN: frames DIX Ethernet frame structure: –The 7-byte preamble is sent before the frame to allow the receiver to synchronize with the signal. IEEE Ethernet frame structure: 4-byte CRC dest address src address lenData DSAP AA SSAP AA cntl 03 org code 00 type MAC802.2 LLC802.2 SNAP 4-byte CRC 6-byte dest address 6-byte src address Data type 0800 IP datagram 2-byte type 7-byte preamble 1-byte start frame delimiter Preamble

Ethernet LAN: MAC protocol Types of MAC addresses: –Unicast address: hardwired into ROM –Broadcast address: all 1 bits –Multicast address: First bit set to 1 and configurable. –Promiscuous mode CSMA/CD (carrier sense multiple access with collision detection) –Each adaptor is able to distinguish a busy link from an idle link. –Each adaptor is able to detect “frame collisions,” if occurred, as it transmits.

Ethernet LAN: MAC protocol To send a frame, –transmits it immediately when the link is detected idle. –The maximum length of the payload is 1500 bytes for a 10-Mbps DIX Ethernet. To receive a frame, –Every adaptor attached to the link will receive a copy of a frame transmitted on the link. –The frame will be discarded if the destination address does not match its unicast address, broadcast address, and any configured multicast addresses.

Ethernet LAN: MAC protocol Carrier sense is not sufficient for avoiding frame collisions. A frame must be long enough to detect collisions: –A sufficient condition: A frame occupies the entire pipe back and forth. –For example, for a 10-Mbps Ethernet segment of 2500m long (a round-trip propagation delay of 51.2  s): Minimum frame length = 51.2  s  10Mbps = 512 bits (64 bytes), or a 14-byte header + a 46-byte payload + a 4-byte CRC.

Ethernet LAN: MAC protocol AB (a) AB (b) AB (c) AB (d)

Ethernet LAN: MAC protocol When more than one adaptor transmits frames “almost at the same time,” –The frames are “collided” and can be detected by the adaptors involved. –The adaptors involved then send a 32-bit jamming sequence, and stop transmission. –The adaptors use exponential backoff for retransmission (up to a limited number of attempts). After first collision: either 0 or 51.2  s. After second collision: 0, 51.2, 102.4,  s. After nth collision: k  51.2  s for k = 0..2 n  1.

Ethernet’s performance Throughput decreases with a and the number of hosts, where –a = propagation delay/transmission delay. Implications: –Limit on the number of stations and the maximum length of the Ethernet segment –Effect of increasing link’s data rate –Support for delay-sensitive data Methods of improving its performance –Each collision domain consists of only one host.

Token ring LAN: physical connectivity Hosts are connected “centrally” to a multi- station access unit (MSAU). Relays are installed to bypass node failure. IEEE uses differential Manchester encoding, a variant of Manchester encoding.

Token ring LAN: physical connectivity Host From previous MSAU To next MSAU

Token ring LAN: MAC protocol Multiple access is regulated by a special 24-bit frame, called token. To send a frame, –Wait for a free token: indicated by a bit in the second byte of the token. –Seize the token and send frames, up to a token holding time (THT=10 ms by default). –The sender is responsible for removing the frames after circulating back to the sender.

Token ring LAN: MAC protocol Token: Data frame: BodyCRC Src addr Variable48 Dest addr 4832 End delimiter 8 Frame status 8 Frame control 8 Access control 8 Start delimiter 8 End delimiter 8 Access control 8 Start delimiter 8

Token ring LAN: MAC protocol To receive a frame, –When a frame is passing a host, it will check the destination address in the frame. –If destination address is a broadcast, or multicast or unicast destined for the host, it will make a copy. –Reliable delivery service via A and C bits in the frame status field: When a host sees a frame destined for it, the host sets the A bit from 0 to 1. After copying the frame successfully, it sets the C bit from 0 to 1.

Token ring LAN: MAC protocol Different from the Ethernet, token ring supports 8 different priorities. –A token’s priority is indicated by a 3-bit field in the access control. –A host may seize a free token of priority m for transmitting priority n frames only if n  m. –A host X may make a “reservation” via a 3-bit reservation field when a data frame is passing it. –When the sender of the frame releases the token, the token priority will be made the same as the value in the reservation field.

Token ring LAN: MAC protocol (a) Early token release vs. (b) delayed token release: T oken Frame T oken Frame (a) (b)

Token ring LAN: ring maintenance Possible problems: –Token loss –Forever circulating corrupted frames –Forever circulating orphan frames –Detection of dead hosts Elect a monitor station to handle most of the ring problems.

39 5. Fiber Distributed Data Interface (FDDI) Physical connectivity: –A dual-ring architecture at 100 Mbps –Use 4B/5B encoding –Optical fiber (FDDI) or copper (CDDI) MAC (timed token rotation protocol) –Nine classes of priority (1 synchronous and 8 asynchronous) –Use early token release –Synchronous transmission limited by a token holding timer (THT)

40 5. Fiber Distributed Data Interface –Asynchronous transmission depends on whether the token is late or early, and how early the token is, as compared with a pre-negotiated target token rotation time (TTRT).

41 5. Fiber Distributed Data Interface For example, hosts A and B transmit synchronous frames, and host C transmits asynchronous frames. –THT A = THT B = 5 ms, and TTRT = 12 ms (2 ms for the total propagation delay in the ring) –After the token leaves C, both A and B use up all their quotas, C’s quota when the token arrives next time is 0 ms. –After the token leaves C again, this time only A uses up his quota and B does not use any. Therefore, C’s quota next time is 12  2  5 ms.

42 6. Wireless LAN (IEEE ) Physical connectivity –Based on spread spectrum radio and diffused infrared –Run at either 1 or 2 Mbps. –Wireless nodes are connected to access points which are connected to one another through a fixed network.

43 6. Wireless LAN (IEEE ) MAC problem: –Hidden node (terminal) problem: Frame collision occurs but the senders involved are unaware of it. A  B and C  B (A and C are not connected) –Exposed node problem: A node is unnecessarily prevented from transmitting frames. B  A and C  D (A and D are not connected) –Both problems are due to the fact that, unlike Ethernet, the nodes are not always connected together.

44 6. Wireless LAN (IEEE ) Multiple Access with Collision Avoidance (MACA) –To send a frame, the sender first sends a Request to Send (RTS) frame to the receiver.

45 6. Wireless LAN (IEEE ) The receiver then replies with a Clear to Send (CTS) frame back to the sender. –Any node that sees the CTS frame will refrain from sending any frames (for the hidden node problem). –Any node that sees the RTS frame but not the CTS frame is free to transmit (for the exposed node problem). –When two or more nodes transmit an RTS frame at the same time, their RTS frames collide. Retransmission of RTS frames takes place after the nodes involved do not receive the CTS frames, i.e. no direct collision detection supported.