Interrupt-Driven I/O There are different types of interrupts –Hardware Generated by the 8259 PIC – signals the CPU to suspend execution of the current.

Slides:

Advertisements

Similar presentations

Chapter 2 (cont.) An Introduction to the 80x86 Microprocessor Family Objectives: The different addressing modes and instruction types available The usefulness.

Advertisements

Chapter 12: Interrupts. Copyright ©2009 by Pearson Education, Inc. Upper Saddle River, New Jersey All rights reserved. The Intel Microprocessors:

Interrupts Disclaimer: All diagrams and figures in this presentation are scanned from the book “Microprocessors and Programmed Logic” authored by Kenneth.

Unit 4 Chapter-1 Multitasking. The Task State Segment.

Microprocessors system architectures – IA32 real and virtual-8086 mode Jakub Yaghob.

8086 Interrupts. Interrupt Normal prog execution is interrupted by – Some external signal, or – A special instruction in the prog.

68HC11 Polling and Interrupts

ECE 372 – Microcontroller Design Parallel IO Ports - Interrupts

Interrupts What is an interrupt? What does an interrupt do to the “flow of control” Interrupts used to overlap computation & I/O – Examples would be console.

6-1 I/O Methods I/O – Transfer of data between memory of the system and the I/O device Most devices operate asynchronously from the CPU Most methods involve.

Introduction An interrupt is an event which informs the CPU that its service (action) is needed. Sources of interrupts: internal fault (e.g.. divide by.

Linux Operating System

1 Interrupts INPUT/OUTPUT ORGANIZATION: Interrupts CS 147 JOKO SUTOMO.

Introduction to Interrupts

Chapter 6 Interrupts (I. Scott Mackenzie).

Introduction to Computer Engineering by Richard E. Haskell Interrupts Module M17.3 Sections 11.3, 14.1.

Interrupts – (Chapter 12)

Lecture 09: Interrupts & 8259.

Interrupts. What Are Interrupts? Interrupts alter a program’s flow of control  Behavior is similar to a procedure call »Some significant differences.

created by :Gaurav Shrivastava

MICROPROCESSOR INPUT/OUTPUT

Khaled A. Al-Utaibi  Interrupt-Driven I/O  Hardware Interrupts  Responding to Hardware Interrupts  INTR and NMI  Computing the.

8086 has 2 interrupt inputs 1. NMI 2. INTR For application where we have interrupts from multiple sources, use an external device called a Priority Interrupt.

I/O Interfacing A lot of handshaking is required between the CPU and most I/O devices. All I/O devices operate asynchronously with respect to the CPU.

Lecture 09: Interrupts & The 80x86 IBM PC and Compatible Computers Chapter 14 Interrupts and the 8259 Chip.

Interrupts Useful in dealing with: The interface: Random processes;

AVR Programming: Interrupts September 17, What are interrupts? An asynchronous signal indicating the need for an event to be handled A synchronous.

CHAPTER 6 INTERRUPTS AND THE 8259 CHIP. What happens on interrupt? Micro automatically saves (on stack) the FR (flag register), IP (instruction pointer),

Accessing I/O Devices Processor Memory BUS I/O Device 1 I/O Device 2.

INT- interrupt program execution 1. It decrements the sp by 2 and pushes the flag registers on the stack. 2. Decrement the sp by 2 and push the content.

CSNB374: Microprocessor Systems Chapter 5: Procedures and Interrupts.

Microprocessor. Interrupts The processor has 5 interrupts. CALL instruction (3 byte instruction). The processor calls the subroutine, address of which.

1 © Unitec New Zealand Interrupt Lecture 6 Date: - 20 Sept, 2011 Embedded Hardware ETEC 6416.

Dec Hex Bin 14 E ORG ; FOURTEEN Interrupts In x86 PC.

8086 Interrupts and Interrupt Applications

MICRO-CONTROLLER MOTOROLA HCS12 Interrupts Mechatronics Department Faculty of Engineering Ain Shams University.

ECE 353 Introduction to Microprocessor Systems Michael J. Schulte Week 11.

Microprocessor System Design Programmable Interrupt Controller.

بسم الله الرحمن الرحيم MEMORY AND I/O.

Interrupts ELEC 330 Digital Systems Engineering Dr. Ron Hayne

The 8051 Microcontroller Chapter 6 INTERRUPTS. 2/29 Interrupt is the occurrence of a condition an event that causes a temporary suspension of a program.

BIOS and DOS Interrupts Basic Input /Outpu System Disk Operating System.

Multiplex of Data and Address Lines in 8088 Address lines A0-A7 and Data lines D0-D7 are multiplexed in These lines are labelled as AD0-AD7. –By.

INTERRUPTS. Topics to be discussed  8088/86 Hardware Interrupts pins 8088/86 Hardware Interrupts pins   Pin description Pin description.

Chapter 10 Interrupts. Basic Concepts in Interrupts  An interrupt is a communication process set up in a microprocessor or microcontroller in which:

1 Interrupts A Course in Microprocessor Electrical Engineering Dept. University of Indonesia.

Unit Microprocessor.

An Interrupt is either a Hardware generated CALL (externally derived from a hardware signal) OR A Software-generated CALL (internally derived from.

COURSE OUTCOMES OF Microprocessor and programming

Interrupts and interrupt responses

MICROPROCESSOR BASED SYSTEM DESIGN

Microprocessor and Assembly Language

68HC11 Interrupts & Resets.

Microprocessor Systems Design I

The process starts from the I/O device

Anton Burtsev February, 2017

Introduction to the processor and its pin configuration

Interrupts In 8085 and 8086.

Interrupts – (Chapter 12)

Microprocessor and Assembly Language

YOVI 2008 Core Interrupt Controller (INTC)

Subject Name: Microprocessors Subject Code:10EC46 Department: Electronics and Communication Date: /20/2018.

Interrupts Interrupt is a process where an external device can get the attention of the microprocessor. The process starts from the I/O device The process.

11.1 Interrupt Mechanism, Type, and Priority

Md. Mojahidul Islam Lecturer Dept. of Computer Science & Engineering

Md. Mojahidul Islam Lecturer Dept. of Computer Science & Engineering

CNET 315 Microprocessor & Assembly Language

Presentation transcript:

Interrupt-Driven I/O There are different types of interrupts –Hardware Generated by the 8259 PIC – signals the CPU to suspend execution of the current program and process the interrupt (keyboard, serial port) Occasionally, programs must disable hardware interrupts when performing sensitive operations on segment registers and the stack. Use CLI (Clear Interrupt flag) to disable interrupts and STI (Set interrupt flag) to enable interrupts. –Software Not really an interrupt (INT) –Internal Interrupts Divide by zero Traps

Responding to Interrupts

Hardware Interrupt Pins NMI – non-maskable interrupt – it cannot be blocked (the CPU must respond) – reserved for critical system functions. INTR – maskable via the IF flag.