King Saud University- College of Engineering- Dept of Chemical Engineering GUIDELINES AND RECOMMANDATIONS FOR THE PREPARATION OF GRADUATE PROJECT I AND II (CHE 498 CHE499) Capstone design committee October 2009

Guidelines 1 INTRODUCTION 2 PROJECT PROPOSAL 3 PROJECT FORMAT 4 ASSESMENTS

1 Introduction –REQUIREMENT FOR PROJECT 1 (CHE498): 32 HOURS –REQUIREMENTS FOR PROJECT 2 (CHE499): CHE 498 – Project Title: suggested title for the project –Supervisor (s): The name of Supervisor for the student (team). If the project is for a company please include that information. –Project must be related a design of a plant or part of a plant and must include mass and energy balances, as well as design of equipment, study of safety and environement aspects and cost calculations. –Project report must be submitted at least one week before the examination and must have the approval of the supervisor.

2 Project proposal form CHE 498 Project Decription Form Student Name : Student No Supervisor name: I PROJECT TITLE: (plant design project) II PROBLEM STATEMENT (Must be related to plant design and include Energy and mass balances calculations, design of major equipment, cost estimation of the whole plant, safety and environmental analysis of the plant), Objective: III WORK PLAN 1ST SEMESTER What is to be accomplished in the project, during semester 1 (CHE498) 2nd SEMESTER - - What is to be accomplished in the project, during semester 2 (CHE499) -

2. PROJECT PROPOSAL PROJECT MUST BE RELATED TO A KNOWN PROCESS WITH AN AVAILABLE FLOW SHEET. GROUP PROJECT: MAXIMUM NUMBER OF STUDENT PER PROJECT IS 2. GROUP PROJECT MUST BE JUSTIFIED (LARGE PLANT..) AND TASKS OF EACH STUDENT MUST BE WELL PRECISED AT THE BEGINNING OF THE PROJECT. ONLY ONE SUPERVISOR PER PROJECT

2. PROJECT PROPOSAL ALL TASKS MUST BE DEFINED INITIALLY, A COPY OF THE PROPOSAL MUST BE ATTACHED IN THE FINAL PROJECTS. NO PROJECTS WILL BE ACCEPTED WITHOUT THE SIGNATURE OF THE SUPERVISOR IN THE FIRST PAGE OF THE PROJECT. ALL PROJECTS MUST BE WRITTEN IN THE SAME FORMAT,(see part 3 ).

2 PROJECT 1 (CHE498) - PROJECT MUST INCLUDE MASS AND ENERGY BALANCES (OVERALL AND INDIVIDUAL) - CALCULATION MUST ME ‘HAND CALCULATIONS’. - SOFTWARE PACKAGES (ASPEN, CHEMCAD ETC..) CAN BE USED AFTER DOING HAND CALCULATIONS. - FOR A GROUP PROJECT: CONTRIBUTION OF EACH STUDENT MUST BE CLEAR

2 PROJECT 2 (CHE499) - PROJECT MUST INCLUDE DESIGN CALCULATION. - AT LEAST TWO MAJOR EQUIPMENT MUST BE FULLY DESIGNED PER STUDENT. -OTHER EQUIPMENT MUST BE SIZED (DIFFERENT EQUIPMENT FOR EACH STUDENT IN THE CASE OF A GROUP PROJECT). - ALL DESIGN CALCULATIONS MUST BE MADE BY HAND AND FULLY EXPLAINED AND JUSTIFIED.

2 PROJECT 2 (CHE499) - SOFTWARE PACKAGES CAN BE USED ONCE HAND CALCULATIONS ACHIEVED. - CLEAR ECONOMIC STUDY MUST BE MADE. -ENVIRONMENT AND SAFETY ISSUES MUST BE COVERED FOR THE APPROPRIATE PLANT AND PRODUCT.

3 FINAL REPORT FORMAT - THE FOLLOWING SECTIONS CONTAIN INFORMATION REGARDING THE DESIRED FORMAT, TYPES SIZES, TYPES FACES TO PREPARE THE FINAL GRADUATE PROJECT, PART I AND PART II. 3.1 GENERAL REPORT PREPARATION THE FINAL REPORT SHOULD INCLUDE IN SEQUENCE: TITLE PAGE (FIRST COVER PAGE), TABLE OF CONTENTS, ACKNOWLEDGEMENT, LIST OF TABLES, LIST OF FIGURES, ABSTRACT, CHAPTERS (SECTIONS) OF THE REPORT FOLLOWED BY RERENCES AND APPENDIX IF ANY. THE STUDENT(S) IS/ ARE REQUIRED TO SUBMIT A CD WITH THE REPORT.

3 FINAL REPORT FORMAT (FRONT COVER PAGE) KING SAUD UNIVERSITY COLLEGE OF ENGINEERING DEPT OF CHEMICAL ENGINEERING FINAL PROJECT I (II) – CHE 498 (CHE499) TITLE OF PROJECT STUDENT NAME (S) Supervisor Name STUDENT NUMBER MONTH YEAR (HAJRI) (GREGORIAN)

3 FINAL REPORT FORMAT 3.2 TYPING SPECIFICATIONS ARIAL (14) SHOULD BE USED FOR TYPING THE TEXT BODY. A A4 SIZE SHEET ONLY WITH MARGINS OF 3.0CM ON EACH SIDE OF THE PAGE. 1.5 SPACE. DO NOT VIOLATE MARGINS, TEXT, TABLES, FIGURES AND EQUATIONS SHOULD NOT EXCEED THE MARGINS. USE FULL JUSTIFICATIONS. EACH CHAPTER OR MAIN SECTION OF THE REPORT SHOULD HAVE AN APPROPRIATE TITLE WHICH SHOULD BE TYPED IN ARIAL (16) UPPER CASE BOLD. USE TWO SPACES BETWEEN SECTIONS. MAIN HEADING SHOULD BE BOLD 14 BOLD SUB HEADING SHOULD BE ARIAL 14 BOLD, INITIAL LETTER SHOULD BE CAPITAL

3 FINAL REPORT FORMAT 3.3 FIGURES AND TABLES ALL FIGURES, TABLES AND GRAPHICS SHOULD BE INSERTED ON SEPARATE PAGES IN THE BODY OF THE REPORT AND MUST APPEAR CLOSE TO WHERE THEY ARE DESCRIBED AND MUST BE NUMBERED. FIGURES CAPTIONS SHOULD BE BELOW THE FIGURES. TABLES CAPTIONS SHOULD BE ABOVE THE TABLES. REFERENCES A LIST OF REFERENCES MUST BE PROVIDED AT THE END OF THE REPORT. THIS LIST SHOULD BE ARRANGED IN THE ORDER OF CITATION IN THE TEXT. NUMBER REFERENCE CITATIONS CONSECUTEVLY IN SQUARE BRACKETS [1]. REFER SIMPLY TO THE REFERNCE NUMBER [2]. THE REFENCE MUST COMPLETE AND PRECISE E.G - NAME OF AUTHOD (BOOK, ENCYCLOPEDIA); Title, volume, pagination, year month, editor, electronic address if any.

3 FINAL REPORT FORMAT 3.4 CALCULATIONS ALL CALCULATIONS MUST BE HAND CALCULATIONS, DETAILED, EXPLAIND AND REFERRED TO FIGURES AND ILLUSTRATIONS WHERE NECESSARY. PACKAGE SOFTWARE CAN BE USED IN ADDTION TO HAND CALCULATION BUT MUST NOT REPLACE HAND CALCULATIONS. ALL SYMBOLS MUST BE DEFINED IN NOMENCLATURE -UNITS UNITS SYMBOLS SHOULD BE USED WITH MEASURED QUANTITIES, 6KG, 3LBM, 51SECS USE SAME SYSTEMS OF UNITS THROUGHOUT ALL THE REPORT (SI UNITS, BRITISH UNITS

4 ASSESMENTS 4.1 CHE 498 ( SUPERVISOR ASSESMENT) Graduate Project I (Che 498) Evaluation form.Student Name : Student No Supervisor name: PROJECT TITLE: (same title as proposal form) FINAL PROJECT SUBMISSION APPROVAL: YES NO.- IF NO: Specify reasons Overall remarks on student’s achievement and performance during the preparation of the project - Marks: / (50) Background review: Literature review- background of the project Problem formulation: Knowledge of: Fundamentals of Chemical Engineering, mathematics, Software packages Problem evaluation: Performing mass and energy balances Written communications: Report- references Student’s performance : Attendance- contribution of student Date Supervisor signature Important: This form must be filled and given prior the submission of the project by the student

4 ASSESMENTS 4.2 Examiners assessments for CHE 498 (50 MARKS) Background Problem formulation and evaluation:-Background of the project, knowledge of fundamentals of Chem.Eng, mass and energy balances calculations: (20 marks) Written communication skills : Report styles, contents, References, languages. (15 marks) Oral communication skills: Slides contents, delivery and skills, responses (15 marks)

4 ASSESMENTS 4.3 Supervisor assessment Project II (ChE 499). (50MARKS) Student Name : Student No Supervisor name: - PROJECT TITLE: (plant design project) FINAL PROJECT SUBMISSION APPROVAL: YES NO - IF NO: Specify reasons Design performance Identify design parameters and assumptions Design and sizing of major equipment Cost analysis Performing cost and profitability analysis of the plant Safety and environmental issues To deal with safety issues and environmental hazards in the process and the plant Written communications and performance Attendance-Report- references

4 ASSESMENTS 4.4 EXAMINERS ASSESSMENT CHE 499 (50 marks) Design performance Identify design parameters and assumptionsDesign and sizing of major equipment Cost analysis, Safety and environmental issues Cost and profitability analysis of the plant Safety issues and environmental hazards in the process and the plant Written communication skills Report styles, contents, references, language

THIS PRESENTATION IS AVALAIBLE IN THE FOLLOWING SITE