Chapter 4 Static Characteristics 4.1 Intuitive Picture 4.2 Collector Current Density and Current Gain 4.3 Output Conductance 4.4 Equivalent Circuit Model.

Slides:



Advertisements
Similar presentations
Chapter 6-1. PN-junction diode: I-V characteristics
Advertisements

Transistors and transistor circuits
Chapter 4 – Bipolar Junction Transistors (BJTs)
1 Fundamentals of Microelectronics  CH1 Why Microelectronics?  CH2 Basic Physics of Semiconductors  CH3 Diode Circuits  CH4 Physics of Bipolar Transistors.
ECE 4339: Physical Principles of Solid State Devices
Chapter 5 Bipolar Junction Transistors
PN Junction Diodes.
Chapter 4 Bipolar Junction Transistor
Department of Aeronautics and Astronautics NCKU Nano and MEMS Technology LAB. 1 Chapter IV June 14, 2015June 14, 2015June 14, 2015 P-n Junction.
Spring 2007EE130 Lecture 23, Slide 1 Lecture #23 QUIZ #3 Results (undergraduate scores only, N = 39) Mean = 22.1; Median = 22; Std. Dev. = High =
EE105 Fall 2007Lecture 6, Slide 1Prof. Liu, UC Berkeley Lecture 6 OUTLINE BJT (cont’d) – PNP transistor (structure, operation, models) BJT Amplifiers –
EE105 Fall 2011Lecture 6, Slide 1Prof. Salahuddin, UC Berkeley Lecture 6 OUTLINE PN Junction Diodes – Reverse Breakdown – Large and Small signal models.
Current Components inside Bipolar Junction Transistor (BJT) NPN BJT.
Chapter 4 – Bipolar Junction Transistors (BJTs)
EE105 Fall 2007Lecture 4, Slide 1Prof. Liu, UC Berkeley Lecture 4 OUTLINE Bipolar Junction Transistor (BJT) – General considerations – Structure – Operation.
Lecture #25 OUTLINE BJT: Deviations from the Ideal
Department of EECS University of California, Berkeley EECS 105 Fall 2003, Lecture 14 Lecture 14: Bipolar Junction Transistors Prof. Niknejad.
EE415 VLSI Design The Devices: Diode [Adapted from Rabaey’s Digital Integrated Circuits, ©2002, J. Rabaey et al.]
© 2012 Eric Pop, UIUCECE 340: Semiconductor Electronics ECE 340 Lecture 38 Introduction to Bipolar Junction Transistor (BJT) Next 4 lectures on the BJT.
Dr. Nasim Zafar Electronics 1 EEE 231 – BS Electrical Engineering Fall Semester – 2012 COMSATS Institute of Information Technology Virtual campus Islamabad.
ECE 342 – Jose Schutt-Aine 1 ECE 342 Solid-State Devices & Circuits 6. Bipolar Transistors Jose E. Schutt-Aine Electrical & Computer Engineering University.
1 Bipolar Junction Transistor Models Professor K.N.Bhat Center for Excellence in Nanoelectronics ECE Department Indian Institute of Science Bangalore-560.
ENE 311 Lecture 10.
Mextram 504 BJT model F. Yuan Advisor : Prof. C. W. Liu Graduate Institute of Electronics Engineering and Department of Electrical Engineering, National.
Bipolar Junction Transistors
EXAMPLE 10.1 OBJECTIVE Solution
SOGANG UNIVERSITY SOGANG UNIVERSITY. SEMICONDUCTOR DEVICE LAB. Bipolar Junction Transistor (1) SD Lab. SOGANG Univ. BYUNGSOO KIM.
Department of Electrical Engineering, National Taiwan University SiGe Technology 陳博文 R
Lecture 26 OUTLINE The BJT (cont’d) Breakdown mechanisms Non-ideal effects Gummel plot & Gummel numbers Modern BJT structures Base transit time Reading:
ENE 311 Lecture 9.
Revision Chapter 5.
ECE 663 Plans What does MCDE give us for the gain? How can we use the equation to improve the gain? Can we develop a compact circuit model for a BJT?
1 Tai-Cheng Lee Spring 2006 Bipolar Junction Transistors (BJT) Tai-Cheng Lee Electrical Engineering/GIEE, NTU.
EE130/230A Discussion 14 Peng Zheng.
Semiconductor Devices Lecture 5, pn-Junction Diode
Introduction to semiconductor technology. Outline –7 Field effect transistors MOS transistor ”current equation" MOS transistor channel mobility Substrate.
Bipolar Junction Transistor (BJT). OUTLINE – General considerations – Structure – Operation in active mode – Large-signal model and I-V characteristics.
Lecture 24 OUTLINE The Bipolar Junction Transistor Introduction BJT Fundamentals Reading: Pierret 10; Hu 8.1.
CHAPTER 5: BIPOLAR TRANSISTORS & RELATED DEVICES
Semiconductor Device Physics
CHAPTER 4: P-N JUNCTION Part I.
Spencer/Ghausi, Introduction to Electronic Circuit Design, 1e, ©2003, Pearson Education, Inc. Chapter 2, slide 1 Introduction to Electronic Circuit Design.
LARGE-SIGNAL BEHAVIOR OF BJTS Large-signal models in the forward-active region Effects of collector voltage in the forward-active region Ohmic and inverse.
BJT Bipolar Junction Transistors (BJT) Presented by D.Satishkumar Asst. Professor, Electrical & Electronics Engineering
CSE251 CSE251 Lecture 2 and 5. Carrier Transport 2 The net flow of electrons and holes generate currents. The flow of ”holes” within a solid–state material.
ECE 333 Linear Electronics
COURSE NAME: SEMICONDUCTORS Course Code: PHYS 473 Week No. 8.
Lecture 4 Bipolar Junction Transistors (BJTs)
BJT Static Characteristics
Lecture 25 OUTLINE The Bipolar Junction Transistor Introduction
Chapter 10 BJT Fundamentals. Chapter 10 BJT Fundamentals.
Lecture 27 OUTLINE The BJT (cont’d) Breakdown mechanisms
Electron-hole pair generation due to light
7.1 Fundamentals of BJT Operation (Qualitative Analysis)
7.8 Frequency Limitations of Transistors
BJT Static Characteristics
Lecture 27 OUTLINE The BJT (cont’d) Breakdown mechanisms
Lecture #25 OUTLINE BJT: Deviations from the Ideal
Lecture 24 OUTLINE The Bipolar Junction Transistor Introduction
Semiconductor Device Physics
Lecture 26 OUTLINE The BJT (cont’d) Ideal transistor analysis
Lecture 25 OUTLINE The Bipolar Junction Transistor Introduction
pn Junction Electrostatics
Lecture 3 OUTLINE Semiconductor Basics (cont’d) PN Junction Diodes
Lecture 26 OUTLINE The BJT (cont’d) Ideal transistor analysis
Lecture 4 OUTLINE Bipolar Junction Transistor (BJT)
BJT Static Characteristics
Chapter 4 Bipolar Junction Transistor
Dynamic characteristic
PN-JUNCTION.
Presentation transcript:

Chapter 4 Static Characteristics 4.1 Intuitive Picture 4.2 Collector Current Density and Current Gain 4.3 Output Conductance 4.4 Equivalent Circuit Model

4.1 Intuitive Picture An ideal,graded-base SiGe HBT with constant doping in the emitter, base, and collector region.  Ge content is linear graded from 0% near the metallurgical emitter-base junction to some maximum value of Ge content near the metallurgical collector-base junction,and then rapidly ramped back down to 0% Ge.  Observe in Fig 4.1 that a Ge-induced reduction in base bandgap occurs at EB edge of the quasi-neutral base, and at the CB edge of the quasi-neutral base.  This grading of the Ge across the neutral base induces a built-in quasi-drift field in the neutral base that will impact minority transport. Fig 4.1:Energy band diagram for a Si BJT and graded- base SiGe HBT,both biased in forward active mode in low-injection.

The Fermi level must realign itself such that it is fixed in energy to its previous (Si) value,and further, that it must be constant (flat) if the system is in equilibrium. This grading of the Ge across the neutral base induces a built-in quasi-drift field in the neutral base that will impact minority carrier transport Induced drift field will positively influence the minority electron transport through the base.The injected electrons diffuse across the base, and sweep into the electric field of the CB junction,yielding a useful collector current. The density of back-injected holes will be small compared to the forward-injected electron density,and hence a finite current gain ß ∝ n/p results. Fig 4.2:Illustration of bandgap changes induced by the introduction of Ge into the base region of an n-p-n SiGe HBT.

The potential barrier to injection of electron from emitter into the base is decrease.Intuitively, this will ylied expontentially more electron injection for the same applied V BE,tanslating into higher collector current and higher current gain.We can trade the higher gain induced by the Ge band offset for a higher base doping level. The present of a finite Ge content in the CB junction will positively influence the output conductance of the transistor,yielding higher Early voltage.

4.2 Collector Current Density and Current Gain Jc in SiGe HBT Relevant Approximations Other SiGe Profile Shapes Implication and Optimization Issue for ß

Jc in SiGe HBT Fig 4.3 Schematic doping and Ge profile used in the derivation. Fig 4.4 Schematic base bandgap in a linearly graded SiGe HBT.

Generalized Moll-Ross collector density relation: With the condition:

We can get the expression With the condition:

We obtain the final expression where Fig 4.5 Comparison of current-voltage characteristic of a comparably constructed SiGe HBT and Si BJT.

The current gain issue Fig 4.6 Measure and calculated current gain ratio as a function of reciprocal temperature for a comparably constructed SiGe HBT and Si BJT. 1000/T

Relevant Approximations First:we can assume that △ E g,Ge (grade)  kT Second:weak Ge grading

Fig 4.7 Theoretical calculation of the current gain ratio as a function of Ge profile shape.

Other SiGe Profile Shapes Fig 4.8 schematic representation of the hybrid Ge trapezoidal profile.  Trapezoids profile

Fig 4.9 current gain ratio as a function of reciprocal temperature for varying ξ values.Noted that the integrated Ge content is not fixed in this case. Fig 4.10 current gain ratio as a function of reciprocal temperature for varying ξ values.Noted that the integrated Ge content is held fixed in this case.

Implication and Optimization issue for ß The present of Ge in the base region will enhance J C at fixed V BE over a comparably constructed Si BJT. The J C enhancement depends exponentially ob the EB boundary value of Ge-induced band offset,and linearly on the Ge grading across the base.  A box Ge profile is better for current gain enhancement than a triangular Ge profile.  The Ge-induced J C enhancement is thermally Activated (exponentially dependent on the reciprocal temperature),and thus cooling will produce a strong magnification of the enhancement.

4.3 Output Conductance V A Trade-offs in Si BJTs V A in SiGe HBTs Relevant Approximations Current Gain-Early Voltage Product Other SiGe Profile Shapes Implication and Optimization Issue for V A and ß V A

VA Trade-offs in Si BJTs Basically Definition And than Q b (0) is the total base charge at V CB =0V,C cb is the base depletion capacitance. Where { W b (0) is the neutral base width at V CB =0 W m is the metallurgical base width  bi is the CB junction built-in voltage { Where

Fig 4.12 Schematic representation impact of the Early effect. Fig 4.11 Schematic representation of the Early effect. Increasing collector concentration degrades V A. Increasing base concentration increasing V A. Increasing base concentration degrades ß. Increasing base concentration degrades f T due to the reduction in the minority electron mobility. It is inherently difficult to simultaneous obtain high V A,high ß,and high f T.

V A in SiGe HBTs  Basically Definition for HBT  And than  If the nib is position-independent,there is no V A enhancement due to Ge.If n ib is position- dependent,V A will depend exponentially on the difference in bandgap between x=W b and that region in the base where n ib is smallest.

Fig 4.13 Dependence of VA on both N dc + and N ab - for a Si BJT. Fig 4.14 Measured and calculated Early voltage ratio as a function of reciprocal Temperature for a comparably constructed SiGe HBT and Si BJT.

Relevant Approximations Fig 4.15 Theoretical calculations f of the VA ratio and ß VA ratio as a function of Ge profile shape. we can assume that △ E g,Ge (grade) ≫ kT we can assume that △ E g,Ge (grade) ≪ kT

Current Gain-Early Voltage Product Fig 4.16 Current gain-Early voltage product ratio as a function for a comparable SiGe HBT And Si BJT.  One conventionally defines a figure-of-merit for analog circuit design:the so-call “ßVA” product.In a conventional Si BJT,it is not favorably impacted by conventional scaling. For a SiGe HBT,however,both ß and VA are decoupled from the base profile,and can be Independent tuned by changing the Ge profile shape.pppppppppppppppppppp

Other SiGe Profile Shapes  Trapezoids profile

Implication and Optimization issue for VA and ß VA Unlike J C,only the presence of a large Ge content at the CB side of the neutral base than at the EB side of the neutral base will enhance V A over a comparably costructed Si BJT. This V A enhancement depends exponentially on the Ge grading cross the base. A triangular Ge profile is better for Early voltage enhancement than a box Ge profile is,everything else being equal. The Ge-induced V A enhancement is thermally activated,and thus cooling will produce a strong magnification of the enhancement. Putting any Ge into base region of a device will exponentially enhance this key analog figure-of-merit,a highly favorable scenario given the discussion above of inherent difficulties of achieving high ßV A in a Si BJT. A reasonable compromise Ge profile design that balance the dc optimization needs of ß,V A,and ßV A would be a Ge trapezoid,with a small Ge content at the EB junction,and a large Ge content at the CB junction.

4.4 Equivalent Circuit Model Basic Ebers-Moll Model Transport Version Small-Signal Equivalent Circuit Model

Basic Ebers-Moll Model A fundamental assumption in this modal is that the overall transistor operation can be viewed as a superposition of both the forward and the reverse mode operation. Fig 18 The basic Ebers-Moll for a bipolar transisitor.

Transport Version

Small-Signal Equivalent Circuit Model

4.5 Avalanche Multiplication Carrier Transport and Terminal Current Forced-V BE Measurement of M Forced-I E Measurement of M Effects of Self-Heating Impact of Current Density Si Versus SiGe

Carrier Transport and Terminal Current Simple analysis shows that the minimum threshold energy for impact ionization is 1.5E g Fig 21 The avalanche multiplication process in a bipolar transistor under normal operation. ……….

Forced-V BE Measurement of M-1 Fig 4.22 Force V BE setup for M-1 measurement.

Forced-I E Measurement of M-1 At high J C and V CB,self-heating and thermal runaway occur.. Fig 4.22 Force I E setup for M-1 measurement.

Effects of Self-Heating

Impact of Current Density

Si Versus SiGe Fig 28 M-1 versus V CB comparison between SiGe HBTs with different Ge profile Fig 27 Simulated depth profile of carrier temperature at V BE =0.7V and VCB=5.

4.6 Breakdown Voltage BV CBO BV CEO Circuit Implication

BV CBO Fig 29 An example of M-1 versus V CB fitting using the Miller equation..

BV CEO Fig 4.30 An illustration of the avalanche multiplication process with an open base..

Circuit Implication