1. Chapter 23 Drilling & Related Hole-Making Processes (Review) EIN 3390 Manufacturing Processes Summer A, 2012

2. 23.1 Introduction Drilling is one of the most common single machining operations. Drilling makes up 25% of machining Most drilling tools have two cutting edges, or lips. Cutting action takes place inside the workpiece The only exit for chips is the hole that is mostly filled by drill Friction between the margin and the hole wall produces heat which is additional to that due to chip formation

3. Nomenclature and Geometry of a Drill FIGURE 23-1 Nomenclature and geometry of conventional twist drill. Shank style depends upon the method used to hold the drill. Tangs or notches prevent slippage: (a) straight shank with tang, (b) tapered shank with tang, (c) straight shank with whistle notch, (d) straight shank with flat notch.

4. Nomenclature and Geometry of a Drill FIGURE 23-1 Nomenclature and geometry of conventional twist drill. Shank style depends upon the method used to hold the drill. Tangs or notches prevent slippage: (a) straight shank with tang, (b) tapered shank with tang, (c) straight shank with whistle notch, (d) straight shank with flat notch.

5. 23.2 Fundamentals of the Drilling Process A conventional two-flute drill, with drill of diameter D, has two principal cutting edges rotating at an rpm rate of N and feeding axially. The rpm of the drill is established by the selected cutting velocity or cutting speed with V in surface feet per minute and D in inches.

6. Conventional Drill Geometry FIGURE 23-2 Conventional drill geometry viewed from the point showing how the rake angle varies from the chisel edge to the outer corner along the lip. The thrust force increases as the web is approached.

7. 23.1 Introduction Four actions take place at the drill tip ◦1. A small hole is formed by the web — chips are not cut here in the normal sense. ◦2. Chips are formed by the rotating lips. ◦3. Chips are removed from the hole by the screw action of the helical flutes. ◦4. The drill is guided by lands or margins that rub against the walls of the hole New drill-point geometry and TiN (Titanium Nitride) coating have resulted in improved hole accuracy, longer life, increased feed-rate capabilities. US manufacturing companies consume 250 million twist drills per year.

8. 23.2 Fundamentals of Drilling process A conventional two-flute drill with diameter D, has two principal cutting edges rotating at rpm rate of N s and feed f r. N s = (12v)/( D) Where V – cutting speed at the outer corner of the cutting lip (point X in Fig. 23 -2)in surface, feet per minute, D – diameter of drill in inch. The depth of cut in drilling is a half of the feed rate, or t = f r /2 (see section A – A in Fig. 23-2), where f r is in inches per revolution.

9. 23.2 Fundamentals of Drilling process The length of cut in drilling equals the depth of the hole, L, plus an allowance for approach and for the tip of drill, usually A = D/2. In drilling, the speed and feed depend upon the material of workpiece, the cutting tool material, and the size of drill. Table 23-1 gives some typical values for V and for carbide indexable insert drills. The maximum velocity is at the extreme ends of the drill lips. The velocity is very small near the center of the chisel end of the drill. Cutting time: T m = (L + A)/(f r N s )= (L +A)/f m where f m is the feed rate inches per minute.

10. Material Removal Rate The material removal rate (MRR) for drilling is: Which reduces to Where T m is cutting time, f r is feed rate, and L is depth of the hole. /min

11. Table 23-1: Recommended Speeds & Feeds for Indexable-Insert Drills

12. 23.2 Fundamentals of Drilling process A cast iron plate is 2” thick, and needs 1” diameter hole drilled in it. An indexable insert drill has been selected. 1) Select cutting speed and feed; 2) the spindle N s and feed rate f m (in/min.); 3) the maximum chip load (depth of cut); 4) MRR; and 5) the total motor horsepower (HPs = 0.33).

15. 23.2 Fundamentals of Drilling process Solution: 1)From table 23-1, select a cutting speed of 200 fpm, and a feed of 0.005 ipr. 2)N s = (12v)/( D) = (12 x 200)/ (3.14 x 1) = 764 rpm, pick 750 rpm. Feed rate f m = f r x N s = 0.005 x 750 = 3.75 in /min, and pick f m = 3.5 in/min. 3) the maximum chip load (depth of cut) t = f r /2 = 0.005/2 = 0.0025 in/rev.

16. 23.2 Fundamentals of Drilling process 4) MRR = (/4) (D 2 ) f m = (3.14/4) x 1 2 x 3.5 = 2.75 in 3 /min. 5) HP =HPs x MRR = 0.33 x 2.75 = 0.9 (horsepower) The value would typically represent 80% of the total motor horsepower needed, so in this case a horsepower motor greater than 1.5 or 2 would be sufficient. HP = 1.6 x 0.9 = 1.5 (horsepower).

17. 23.3 Types of Drills The most common drills are twist drills Twist drills have three parts ◦Body: consisting of two or more spiral grooves called flutes, separated by lands. Flutes serve as channels through which chips are withdrawn from hole and coolant gets to cutting edges. ◦Point: a wide variety of geometry are used, but typically have a cone angel of 118°, and a rake angle of 24° ◦Shank: a straight or tapered section where the drill is clamped.

18. Specialized Tips Specialized tips are used to produce self centering holes where hole position is critical. ◦Helical tips (eliminate center drilling) ◦Four-facet tips (good self-centering ability) ◦Racon (Radiused conventional point) ◦Bickford (Combination of helical and Racon) ◦Center core, or slot drills Used in machining centers and high speed automatic NC systems where manual center punching is impractical

19. Drill Point Geometry FIGURE 23-4 As the drill advances, it produces a thrust force. Variations in the drill-point geometry are aimed at reducing the thrust force.

20. Drill Point Geometry FIGURE 23-4 As the drill advances, it produces a thrust force. Variations in the drill-point geometry are aimed at reducing the thrust force.

21. Center Core Drill FIGURE 23-5 Center core drills can greatly reduce the thrust force.

22. Typical Causes of Drilling Problems

23. Depth-to-Diameter Ratio Standard drills typically are used to produce holes with a depth to diameter ratio of 3:1 Deeper holes result in drift of the tool decreasing hole straightness Specialized drills called deep-hole drills or gundrills are used for greater ratios Gundrills are single tipped tools with a coolant channel delivering coolant to the tip and flushing chips to the surface Ratios of 100:1 are possible with gundrills

24. Gundrills Geometry FIGURE 23-7 The gundrill geometry is very different from that of conventional drills.

25. Drill Processes Compared

28. 23.4 Tool Holders for Drills Straight-shank drills are typically held in chucks ◦Three-jaw jacobs chucks: used on manual drill presses, require a key ◦Collet chuck: used with carbide tools where high bearing thrust is used ◦Quick change chucks: used where rapid change is needed Tapered shank drills held in mores taper of the machine spindle

29. Correct Chucking of Carbide Drills FIGURE 23-17 Here are some suggestions for correct chucking of carbide drills.

30. 23.5 Workholding for Drilling For prototype pieces, stock material is held in simple clamping vises For high production rates, custom jigs are used Stock material is never to be held on the work table by hand

31. 23.6 Machine Tools for Drilling Drilling can be performed on: ◦Lathes ◦Vertical mills ◦Horizontal mills ◦Boring machines ◦Machine centers Specialized machines designed specifically for drilling called “drill presses”

32. Requirements of a Drill Press Drill presses must have sufficient power and thrust to perform cut Drill presses must be rigid enough to prevent chatter Drill press consist of a base, a work table, and a column that supports the powerhead and spindle

33. Summary Drilling is the most common machining operation Drilling can be performed on a number of machine tools, drill machines are specialized machine tools for drilling only Drills come in a wide variety of types and tip geometries depending upon production rate and accuracy needed Hole geometries can be adjusted through the use of counterboring, countersinking and reaming

34. HW for Chapter 23 Review Questions: 1, 2, 10, and 25 (page 653-654) Problems (page 654): 3, 5, 7, 9