3. General SafetyBand SawMitre Saw Miscellaneous Machines 1000 2000 3000 4000 Next

4. General Safety What is the first thing each student must do upon entering the lab?

5. General Safety Put on Safety Glasses

6. General Safety What is the consequence for not wearing appropriate clothing for lab days?

7. General Safety Loss of lab time, loss of project points

8. General Safety While in the lab, you should not talk to someone while they are doing what?

9. General Safety Operating a machine

10. General Safety What should be done throughout and at the end of each class period?

11. General Safety Thorough clean-up

12. Band Saw The saw guide should be set to within ______ of the stock before turning on the power.

13. Band Saw ½ inch

14. Band Saw Where is a bad place to stand while a band saw is in operation?

15. Band Saw At the right side of the saw table

16. Band Saw Why is this saw called a “Band Saw?”

17. Band Saw The blade is a large revolving band.

18. Band Saw What must you first do in order to make a curved a cut using the band saw?

19. Band Saw Make relief cuts

20. Mitre Saw Before cutting into your material, make sure the saw blade is at full _______?

21. Mitre Saw speed

22. Mitre Saw What should the material be firmly and securely held against while cutting?

23. Mitre Saw The Fence

24. Mitre Saw As you pass the blade through your material, which direction do you slide the blade?

25. Mitre Saw Away from you.

26. Mitre Saw You should always keep your hands at least inches from the saw blade.

27. Mitre Saw 8

28. Miscellaneous Machines -2 Part Question- With which machine are you required to clamp your work to the table and why?

29. Miscellaneous Machines Drill Press, to keep the drill from catching your material and spinning it around And Mitre saw if possible, for extra stability

30. Lose a Turn!

31. Miscellaneous Machines When using the drill press, you lower the spinning bit approximately how far before backing it out?

32. Miscellaneous Machines ½ inch

33. Miscellaneous Machines When using the spindle sander, you always sand in what direction compared to the spindle movement?

34. Miscellaneous Machines Opposite

35. Sander Safety General Saw Safety Tool IDWild Card 6000 8000 10,000 12,000

36. Sander Safety It is important that you always use pressure when using any of the power sanders.

37. Sander Safety Light

38. Sander Safety Why should the material being sanded always be kept on the work table?

39. Sander Safety It reduces the chance of the material being pulled out of the operator’s hands and hurting someone.

40. Sander Safety Always keep your hands away from ______?

41. Sander Safety Moving Sandpaper

42. Lose a Turn!

43. General Saw Safety Your fingers should always be a minimum of inches away from a moving saw blade.

44. General Saw Safety 2

45. What should you do to protect yourself if your fingers are going to be near a moving saw blade?

46. General Saw Safety Use a Push Stick

47. General Saw Safety Once you have finished cutting your material and have turned off the machine, what do you do next?

48. General Saw Safety Wait for the blade to stop moving

49. General Saw Safety In the correct order, what 3 steps should you take if a blade breaks while you are operating a saw?

50. General Saw Safety Shut it off, Unplug it, Go get the teacher

51. Tool ID

52. Band Saw

53. Tool ID

54. Try Square

55. Tool ID

56. Nail Set

57. Tool ID

58. Coping Saw

59. Lose a Turn!

60. Wild Card If done on purpose, what will earn you an automatic detention in the lab?

61. Wild Card Pressing the Emergency Stop Button

62. Wild Card What should you do if you are nervous about using a machine?

63. Wild Card Ask the teacher for help

64. Wild Card There are two areas that must be perfectly organized before you are dismissed on project days. What are those two areas?

65. Wild Card Broom Area & Safety Glasses Cabinet