Presentation is loading. Please wait.

Presentation is loading. Please wait.

Model 466_666 Thorough and regular cleaning, in accordance with the working conditions, is recommended. The gauges are fitted with two bleed cap that.

Published byGyles Ferguson Modified over 8 years ago

Similar presentations

Presentation on theme: "Model 466_666 Thorough and regular cleaning, in accordance with the working conditions, is recommended. The gauges are fitted with two bleed cap that."— Presentation transcript:

1

2 Model 466_666 Thorough and regular cleaning, in accordance with the working conditions, is recommended. The gauges are fitted with two bleed cap that allows the thorough cleaning of crystallisations and sediments by introducing a rod with a maximum diameter of 7 mm. In the event of a leak in the watertight areas, tighten the seal gland nut again. If the leaks persist, replace the graphite rings while the level indicator box is out of service. MAINTEINANCE

3 Model 466_666 1. Disassembly To replace de graphite rings or clean any of the internal components of de valve, proceed in the following manner : A.Remove the nut, the washer, and release the lever. B.Loosen the seal gland nut, and remove it through the axle together with the seal gland. C.Using pliers, remove the remains of the old graphite rings and replace them with new ones. DISASSEMBLY AND ASSEMBLY

4 Model 466_666 2. Assembly A.Put the seal gland, and the seal gland nut, back in place and tighten with a flat spanner. B.Put the lever, the washer, and the nut, back in place and tighten. DISASSEMBLY AND ASSEMBLY

5

Download ppt "Model 466_666 Thorough and regular cleaning, in accordance with the working conditions, is recommended. The gauges are fitted with two bleed cap that."

Similar presentations

RP4A 2½ – 6. Modification Overview Production of the RP4A series began in 2008. Production of the RP4A series began in 2008. A Lead free version (4ALF)

RP4A 2½ – 6. Modification Overview Production of the RP4A series began in Production of the RP4A series began in A Lead free version (4ALF)
RP4AN 21/2 – 6. Modification Overview Production of the RP4AN series began in 2008. Production of the RP4AN series began in 2008. The 4AN indicates an.

RP4AN 21/2 – 6. Modification Overview Production of the RP4AN series began in Production of the RP4AN series began in The 4AN indicates an.
Informações Técnicas Engenharia de Aplicação - BGL 1 Preparation before assembling Keep the assembling area dry and dust free. Check the shaft, housing.

Informações Técnicas Engenharia de Aplicação - BGL 1 Preparation before assembling Keep the assembling area dry and dust free. Check the shaft, housing.
Instructions for making plunger fork tool. Drawing for the trigger assembly.

Instructions for making plunger fork tool. Drawing for the trigger assembly.
3.1.9 Student Book © 2004 Propane Education & Research CouncilPage 1 3.1.9 Replacing Valves and Fittings in ASME Tanks Replacing ASME tank valves and fittings.

3.1.9 Student Book © 2004 Propane Education & Research CouncilPage Replacing Valves and Fittings in ASME Tanks Replacing ASME tank valves and fittings.
Instructions for Diaphragm Replacement Cat. Nos. 2052B-01, 2054B-01

Instructions for Diaphragm Replacement Cat. Nos. 2052B-01, 2054B-01
ZIPP 404 BEARING REPLACMENT GUIDE Tools Needed:

ZIPP 404 BEARING REPLACMENT GUIDE Tools Needed:
Rework Procedure for Wash Motor Pulley Change Model : Rosa & Rosa Plus Part Details & Tools required Sr NoPart DescriptionQtyTool used to replace old artworks.

Rework Procedure for Wash Motor Pulley Change Model : Rosa & Rosa Plus Part Details & Tools required Sr NoPart DescriptionQtyTool used to replace old artworks.
A Manual for Repair and Maintenance Technicians 1ST STAGE.

A Manual for Repair and Maintenance Technicians 1ST STAGE.
Model 695AV 1. Dissasembly To replace the spring, or clean any of the internal components of the valve, proceed in the following manner: A.Cut the seal.

Model 695AV 1. Dissasembly To replace the spring, or clean any of the internal components of the valve, proceed in the following manner: A.Cut the seal.
RPDA 4A 2½” – 6”. Modification Overview  Production of the RPDA 4A series began in 2008.  The RPDA 4A can utilize either a Type I or Type II bypass.

RPDA 4A 2½” – 6”. Modification Overview  Production of the RPDA 4A series began in  The RPDA 4A can utilize either a Type I or Type II bypass.
Chapter 11, Section 4. Changing a Shower Head 1.Turn off the water. 2.Remove the old showerhead. 3.Clean the showerhead stem of any corrosion or buildup.

Chapter 11, Section 4. Changing a Shower Head 1.Turn off the water. 2.Remove the old showerhead. 3.Clean the showerhead stem of any corrosion or buildup.
Model 495/496 EP Full lift safety valve with spring loading (AIT) model 495/496 - EP. 1. Disassembly and assembly. 1.1 Disassembly. To replace the spring,

Model 495/496 EP Full lift safety valve with spring loading (AIT) model 495/496 - EP. 1. Disassembly and assembly. 1.1 Disassembly. To replace the spring,
860 21/2”-10”. Modification Overview  Production of the 2½” – 10 sizes began in 1993.  Lead free version (LF860) was introduced in 2011. Parts do not.

860 21/2”-10”. Modification Overview  Production of the 2½” – 10 sizes began in  Lead free version (LF860) was introduced in Parts do not.
Tire Servicing Program. Agenda WorkSafeBC Requirements Definitions Responsibilities General safety.

Tire Servicing Program. Agenda WorkSafeBC Requirements Definitions Responsibilities General safety.
Hot Rod TM bleeder cleaner Inspection, Maintenance and Operating Procedures.

Hot Rod TM bleeder cleaner Inspection, Maintenance and Operating Procedures.
Model 095-096 DISASSEMBLY AND ASSEMBLY 1- Disassembly To replace the spring (11), or clean any of the internal components of the valve, proceed in the.

Model DISASSEMBLY AND ASSEMBLY 1- Disassembly To replace the spring (11), or clean any of the internal components of the valve, proceed in the.
Model 995 EP DISSASSEMBLY AND ASSEMBLY 1.Disassembly To replace the spring or clean any internal components of the valve, proceed in the following manner:

Model 995 EP DISSASSEMBLY AND ASSEMBLY 1.Disassembly To replace the spring or clean any internal components of the valve, proceed in the following manner:
Model 895 AP DISSASSEMBLY AND ASSEMBLY 1.Disassembly To replace the spring or clean any internal components of the valve, proceed in the following manner:

Model 895 AP DISSASSEMBLY AND ASSEMBLY 1.Disassembly To replace the spring or clean any internal components of the valve, proceed in the following manner:
Model 495/496 AP and CP Full lift safety valve with spring loading (AIT) model 495/496 - AP and CP. 1. Disassembly and assembly. 1.1 Disassembly. To replace.

Model 495/496 AP and CP Full lift safety valve with spring loading (AIT) model 495/496 - AP and CP. 1. Disassembly and assembly. 1.1 Disassembly. To replace.

Similar presentations

Ads by Google