1. Kysor Panel Systems Product/ Tools Training

2. Kysor Basics Section 2

3. Partition Walls & Top Connections Walls shared by multiple boxes within a unit to minimize wall space Used when walls are same thickness and panel is able to span over sides Used when joint butt up against each other and are the same thickness and/or different finishes on either side

4. Partition Walls & Top Connections, cont’d Used when walls are different thickness and outside heights must match Used when walls are different thickness and inside heights must match Other connection types are available as non- standard

5. Spline & Tee Panels Panels used to connect partition walls Attaches partition walls to outer walls Construction will match quoted panels Spline location on walls can be no closer then 1 ½” from edges to start of spline T-Corner and spline corner legs (long side) not to exceed 40” with a minimum of 1 ½” past interior face Can be NSF and Non-NSF PARTITION WALL COOLER/FREEZER WALL

6. Spline & Tee Panels, cont’d NSF Spline Non-NSF Spline Tells the dimension for each side from center NSF T-Panel Non-NSF T-Panel Tells the dimension of each side of T- Panel

7. Pits Pits are used to recess the insulated floor panel so it’s surface is level to the adjoining floor surface Pits must be level and square Sometimes pits are deeper to compensate for poor concrete At times floors must be shimmed or leveled with sand

8. Pits, cont’d Pit depth must be shown on the drawing Descriptions for pits should state the O.A. height A.F.F., then size of the pit (Example: 8’ High A.F.F. With 4” pit) A.F.F. – Above Finished Floor At times our wall panel is used as the concrete form.

9. Curbs Curbs are used to protect wall panels Curbs can be poured against the wall after they are installed Curbs can be poured prior to panel installation Freezer applications require a breaker strip and a continuous vapor barrier Curbs must be checked by customer prior to manufacturing of panels

10. Thermal Breaks and Barriers Used to cause a break in material that will transfer temperature when there is a difference in temperature from one side of a wall to the other Common Uses: Columns in freezers Insulated slabs Door Jambs Partition walls

11. Knee Walls Used when there is a common wall where the cooler is taller than the freezer Tops to counter-sink lags into bottom section prior to knee wall placement Use 1 ½”x1 ½” 14 GA. Galvanized angle and fasten to TRD’s and tops with #14 x 1” Hex Head screws 6” flat trim fastened with #8 x ¾” Hex Head screws to cover seam

12. Parapet Walls Used when customer wants to conceal their tops Use 1 ½”x1 ½” 14 GA. Angle at top and bottom connections with #14 x 1” Hex Head screws @ 12” O.C. May require conduit bracing depending on the height of panel May require 2”x4” blocking using 3/8”x2” lag bolts depending on height of panel Optional Conduit Bracing Optional Blocking

13. Butyl & Silicone Butyl Perimeter of wall base Exterior side of all freezer joints Behind termination bar of membrane roof Approximately 15’ per tube Silicone: Perimeter of tops to wall Exterior exposed joints on outdoor boxes Available in white, grey, or clear Outdoor units need a high humidity silicone Approximately 20’ per tube All outdoor units have recessed gasket where exposed to allow silicone in all joints

14. Freight Options Contract Carrier: Dedicated truck Can set appointment for delivery Use this form for all KPS installed units Trailers are 48’ long Maximum of 4,000 square feet per trailer Rate based on mileage More expensive option If shipment is going to a congested area or where shipping restrictions apply, it may be necessary to ship on a dedicated goose neck truck Motor Freight: Shared truck and product needs to be packaged accordingly. Crating must be included in quote Delivery time can not be guaranteed Trailers are 24’ long Maximum for SINGLE panels is 20’ Maximum for full jobs are 14’ long Maximum square footage is 850-1000 Rate based on weight Buyout Items Included (cost of freight from manufacturer to plant or site is included in cost of buyout) Non-Included (cost of freight from manufacturer to plant or site will be billed to customer separately) 3 rd Party (cost of freight from manufacturer to plant or site will be billed to customer by vendor) Refrigeration freight to plant (1 st destination) is included in the price Steel freight to plant is included in the price Items to include for freight charges from plant to site: Panels Buyout items Refrigeration Steel F.O.B. Factory is KPS Standard

15. Convenience Store Standards 3 ½” & 5” Wood-Framed Panel Lag Down Tops Natural Embossed Galvanized Interior & Exterior Strip Screed Natural Smooth Aluminum Floor Covebase (match interior finish) Inset door 18 GA Galvanized Jambguards Light, Switch, & Thermometer 6 ½” BRD for Reach-In Doors

16. Food Service Standards SERIES 1 4” Insul-Frame Panel Lock Down Tops and Floors Natural Embossed Galvanized Interior & Exterior Concealed Angle Covebase (match interior finish) Natural Smooth Aluminum Floor Flushmount FRP Door 3’ High DTA Kickplates Interior & Exterior Factory Cap Trim Light, Switch, & Thermometer 6 ½” BRD for Reach-In Doors

17. Environmental Test Chamber Standards 4” Insulframe Panels Non-Wood Construction Lock Down Tops and Floors White Embossed Aluminum Interior and Exterior Concealed Angle.080 Natural Smooth Aluminum Floor Flushmount FRP Door Factory Cap Trim Cove Base (Match Interior Finish) Light & Switch

18. Outdoor Environmental Enclosures Wood-Framed Panels with Pressured Treated Lumber Lag Down Tops Mesa Profile 22 Ga. Polar White Exterior & 26ga White Embossed Galvanized Interior Finish 2 ½” x 1 ½” 22 Ga. Angle Screed with Clips Diamond Tread Aluminum Floor Metal Commercial Doors (Buyout Door) Tapered side walls for slope Weather Hoods Standing Seam Roof Multiple small openings for customer supplied equipment

19. Supermarket Standards 3 ½” & 5” Wood-Framed Panels Lag Down Tops Natural Embossed Galvanized Interior & Exterior Strip Screed Natural Smooth Aluminum Floor Inset Door 18 Ga. Galvanized Jambguards 3’ High DTA Kickplates Interior & Exterior Field Installed Cap Trim Switch & Thermometer 6 ½” BRD for Reach-In Doors

20. Warehouse Standards Wood-Framed Panels Lag Down Tops Field Installed Top Trim Natural Embossed Galvanized Interior & Exterior 1 ½” x 1 ½” 18 Ga. Screed Inset Door 18 Ga. Galvanized Jambguards 3’ High DTA Kickplates Interior & Exterior Tall single span panels or stacked panels w/girt line for taller applications Large openings for sliders and rapid roll-ups or strip curtains

21. This is the end of the Basic Panels #2 lesson. Click Angled Arrow on left side of page to return to Course Page. You can take the quiz now or return at a future time.