1. PUMPS

2. Flo Fab Pumps: Overview Vertical Inline Base-mounted
Design philosophy, common features, etc…
Vertical Inline
Circulators, closed-coupled, spacer-coupled
Base-mounted
End suction, closed-coupled, spacer-coupled, split case, double-suction, unique configurations
Submersibles
Sewage, effluent, column, stainless steel, duplex, panels, accessories

3. Flo Fab Pumps:
All Flo Fab pump products are made with a resin pattern which results in an improved exterior finish, smooth interior passage, and higher efficiency pumps
Quiet operation, especially at 1750 rpm
Quick delivery on series 600, 700, 880, 880RI, 1000, and 2000, 2600 pumps
Interchangeable parts impeller, bracket, mechanical seal and coupling on series 700, 880, 880RI, 1000 and 2000.
Standard available parts from any service centers, (Woods couplings, standard motors, standard mechanical seal, standard bearings)  
Impellers are hydraulically trimmed and balanced to every selected condition

4. Flo Fab Pumps:
All pumps are factory tested and certified performance test is available when requested by the consultant.
Test facilities up to 400 HP with 24,000 gallon test bench with calibrated instruments
Engineers on staff, quality controls, CAD drawings and a modern factory back-up warranty
Competitively priced products
Full line of complementary accessory products
Full product catalogues are available

5. Vertical Inline Flo Fab Pumps:
Series 600
Closed-coupled x 1-2 to 3 x 3 x 5
Series 700
Closed-coupled ½ x 1 ½ x 7 to 3 x 3 x 7
Series 880
Closed-coupled VIL x 2 x 8 to 8 x 8 x 12
Series 840SC
Spacer-coupled VIL x 2 x 8 to 16 x 16-19
Series 880RI
Spacer-coupled VIL x 2-8 to 8 x 8-12

6. Series 600 / 700 - Vertical Inline Pumps
Closed-coupled / No Coupling
Stainless steel shaft
Cast iron bracket vs. aluminium
Vertical or horizontal position
Flanges are supplied with each pump
No bearing assembly (no maintenance)
Impeller is trimmed and balanced to every condition.

7. Series 600 / 700 - Vertical Inline Pumps
Standard motor replacement
Back pullout design allows maintenance without disturbing the pipe
Suction and discharge gauge tappings are standard
All iron ,bronze fitted or all bronze construction material
Standard 250 °F mechanical seal (carbon vs ceramic, elastomer is Viton with stainless steel spring) standard in the industry.

8. Series 880 & 880RI: Vertical Inline Pumps
Cast iron bracket interchangeable with series 700,880RI,1000, 2000
Vertical or horizontal position (up to 5 hp)
Some brackets have additional motor mountings for different size motor frames and different HP
Impellers are available in all iron, all bronze, or all stainless steel
Suction and discharge gauge tappings are standard
Bronze replaceable wear ring for casing
All iron, bronze fitted or all bronze construction material
Standard 250 °F mechanical seal (carbon vs. ceramic, elastomer is Viton with stainless steel spring) standard in the industry. (other materials for high temperature are available)
Drain plug at the bottom of the casing
Thermometer socket connection at the suction casing

9. Series 880 & 880RI: Vertical Inline Pumps
250 psi flange casing standard (drilled to 150 # or 250 # ) no extra cost
3 and 4 inch pumps have pre-drilled bolt tappings and sized for either line sizes
Flanges are tapped for NC bolts
4 extra tappings on the suction pump flange suction are standard
5 extra tappings on the pump discharge flange are standard (for gauges, temp relief valve, cyclone separator, flush line)
Special tappings on discharge flange for pitot tube.
Floor mounting square pedestal with 4 bolts holes is standard
Stainless steel suction diffuser on the pump inlet (optional) with holding set screw already pre-drilled

10. Series 880 & 880RI: Vertical Inline Pumps
3 and 4 inch pumps are pre-drilled and suited for either sizes
Flanges are tapped for NC bolt thread
4 extra tappings on the suction pump flange suction are standard
5 extra tappings on the pump discharge flange are standard (tappings can be used for gauges, temp relief valve,
cyclone separator, flush line)
Special tappings on discharge side of the pump flange for a pitot tube insertion (which will allow
you to read differential pressure and go to
a GPM flow chart) standard (however pitot
tube is an option and must be specified by
the consultant.
Standard floor mounting square pedestal
with 4 bolt holes
Stainless steel suction diffuser on the pump inlet (optional) with holding set screw already pre-drilled

11. Series 880: Vertical Inline Pumps
Closed-coupled 2 x 2 x 8 to 8 x 8 x 12
JM frame motor & pump shaft - bronze sleeve (stainless steel sleeve is optional) motors are available but with limited suppliers
Self-aligned
Standard JM motor replacement
Back pullout design allows maintenance without disturbing the pipe
test

12. Series 880RI: Vertical Inline Pumps
Spacer-coupled
TC frame motors have steel or stainless steel shaft
Motors are available with unlimited suppliers (easy to source)
Stainless steel pump shaft on the power frame are with bronze sleeve or (stainless steel sleeve is optional).
Two power frames available LF1 and LF2 for different HP
Same power frames are used for horizontal series 2000 pumps
Impeller is trimmed and balanced to every condition
Standard Woods spacer coupling self aligned
because of the motor bracket placement
Power frame pull-out design allows:
Easy maintenance
Replacement of impeller without removing the motor
Trimming of the impeller
Standard changing the mechanical seal
Standard changing power frame bearings
Standard changing the pump shaft
Standard changing wear ring
While not removing the motor and without disturbing the pipe

13. Series 880RI: Vertical Inline Pumps
Parts that can be removed while pump & motor stay online:
Coupling
Shaft
Power assembly
Bracket
Pump seal
Impeller
Wear ring

14. Series 880RI: Vertical Inline Pumps
Bracket for series and 880RI

15. Series 840SC : Vertical Inline Pumps
No flanges are tapped with NC bolts threads: longer bolts and nuts are required.
Special maintenance
Cannot replace the impeller unless the motor is removed
Cannot trim the impeller unless the motor is removed
No bearings to support the pump shaft
Cannot change the pump shaft or wear rings without removing the motor
Special ductile iron spacer coupling
Special seal
Special motor

16. Series 840SC: Vertical Inline Pumps
Suction and discharge gauge tappings are standard (1 tapping on the suction flange, 1 tapping on the discharge flange)
Bronze replaceable wear ring for casing standard
All iron, bronze fitted or all bronze construction material
Standard 250 °F mechanical seal (carbon vs. Ceramic, elastomer is Viton with stainless steel spring) standard in the industry. (other materials for high temperature are available)
Drain plug at the bottom of the casing
150 psi flange casing standard
Floor mounting square pedestal with
4 bolts holes
The only advantage is the replacement
of an expensive outside seal

17. Series 840SC: Vertical Inline Pumps

18. Motor Motor bracket Coupling Shaft Pump seal Impeller Wear ring
Series 840SC: Vertical Inline Pumps
Motor
Motor bracket
Coupling
Shaft
Pump seal
Impeller
Wear ring

19. Series 880RI: Vertical Inline Pumps

20. Flo Fab Base-mounted Pumps:
Series 1000
End suction, closed-coupled less base 2 x 1 x 6 to 6 x 5 x12
Series 2000
End suction, base-mounted x 1 x 6 to 6 x 5 x12
Series 2600
End Suction, base-mounted x 2 x 5 to 12 x 10 x 18
Series 6000
Single-suction, base-mounted x 1.5 x 8 to 12 x 10 x 17
Series 4800V/H Horizontal & Vertical Split Case
Double suction, base-mounted x 3x 8.3 to 18 x 14 x 17.2
Series 4800L & 4800U – Vertical or Horizontal Split Case
Double suction, base-mounted x 3 x 8.5 to 16 x 14 x 15

21. Series 1000 / 2000 / 880 and 880RI Closed Coupled Pumps
Cast iron bracket interchangeable with series 1000 – 2000, and 880,880RI
Casing rotation to eight possible positions
Some brackets have additional motor mountings holes for different size motor frames and different HP motors
Impellers are available all iron, all bronze, or all stainless steel
Back pull-out design allows
Easy maintenance
Replacement of impeller,
Trimming of the impeller
Standard changing the mechanical seal,
Standard changing power frame bearings
Not having to remove the pump casing to service the pump
parts and without disturbing the pipe
Suction and discharge gauge tappings are standard
Bronze replaceable wear ring for casing
All iron, bronze fitted or all bronze construction material
Standard 250 °F mechanical seal (carbon vs. Ceramic, elastomer is Viton with stainless steel spring) standard in the industry. (other materials for high temperature are available)
Drain plug at the bottom of the casing
250 lbs casing is standard with flange or NPT connections
Flanges are pre-drilled to 150 lbs (250 lbs is optional)
Pre-drilled anchor holes with grout hole is standard with all steel base plate at no extra cost

22. Closed-coupled, end-suction less base
Series 1000 Closed Coupled Pumps
Closed-coupled, end-suction less base
JM frame motor as pump shaft and bronze sleeve (stainless steel sleeve is optional) motors are available but with limited suppliers
Horizontal position without a base plate
No spacer coupling is required: self-aligned because of the motor bracket placement
Standard JM frame motor replacement
1 tapping on the pump discharge flange is standard
Steel base plate on closed coupled pumps is an extra cost but available

23. Series 1000: Flo Fab Closed Coupled Pumps
Motor, Shaft, Bracket, Seal, Impeller, Wear ring

24. Series 2000: Flo Fab Base-mounted Pumps
Motor; Coupling; Shaft; Power Frame ; Pump seal;
Bracket; Impeller; Wear ring

25. Series 2000 / 2600 Base mounted Pumps
T frame motors have steel or stainless steel shafts
Motors are available with unlimited suppliers (easy to source)
Stainless steel pump shaft on the power frame are with bronze sleeve or (stainless steel sleeve is optional).
Steel coupling guard and soon OSHA (Occupational Safety and Health Administration) guard will be standard
T frame motors have steel or stainless steel shaft is available
Motors are available from large number of suppliers

26. Series 2000: Flo Fab Base-mounted Pumps
Spacer-coupled, base-mounted, end-suction 2 x 1 x 6 to 6 x 5 x 12
2 power frame for the entire line of pumps LF1 & LF2 for different HP size motors
Horizontal position with a steel base plate
Standard T frame motor replacement

27. Series 2600: Flo Fab Base-mounted Pumps
Spacer-coupled, end-suction, base-mounted up to 14” suction
Horizontal position with a cast-iron base plate
Industrial quality oil sump for bearing assembly
Oil level sight glass
Cast-iron base doesn’t require grouting
Discharge& suction gauge tappings are standard

28. Series 6000: Flo Fab Base-mounted Pumps
single suction, base-mounted 1.5 x to 12 x 10-17
16 different configurations
Suction
Discharge
Motor
Coupling
Shaft
Power Frame
Bracket

29. Series 6000: Flo Fab Base-mounted Pumps
16 different configurations:

30. Double-suction split case base-mounted 5 x 3-8.3 to 18 x 14 X 17.2
Series 4800 V/H: Base-mounted Pumps
Double-suction split case base-mounted 5 x to 18 x 14 X 17.2
Parts that can be removed while pump & motor stay online:
Coupling
Shaft
Top cover
Pump seal
Bearing assembly
Impeller
(hidden)
(hidden)
(hidden)
(hidden)

31. Series 4800L & 4800U: Base-mounted Pumps
Spacer-coupled, double configuration, double suction, base-mounted 5 x 3 X 8.5 to 16 x 14 x 15
Parts that can be removed while pump & motor stay online:
Coupling
Shaft
Bracket
Pump seal
Bearing assembly
Impeller

32. Flo Fab Submersible Pumps:
Sewage
Effluent
Grinder
Column
Accessories

33. Sewage FBV Up to 3” solids Up to 15HP Over 70’ lift Up to 317 usgpm
Series FBV: Flo Fab Submersible Pumps:
Sewage FBV
Up to 3” solids
Up to 15HP
Over 70’ lift
Up to 317 usgpm

34. Effluent LB, LBV, LBK Up to 2” solids Up to 1HP Over 50’ lift
Series LB,LBV & LBK: Flo Fab Submersible Pumps:
Effluent LB, LBV, LBK
Up to 2” solids
Up to 1HP
Over 50’ lift
Up to 185 usgpm

35. Effluent elevator PD & PDZ
Series PD & PDZ: Flo Fab Submersible Pumps:
Effluent elevator PD & PDZ
Up to 3/8” solids
Up to 1.5 HP
Over 60’ lift
Up to 87 usgpm
Stainless steel construction
Commercial/residential use

36. Grinder FGC Up to 3” solids Up to 3HP Over 80’ lift Up to 61 usgpm
Series FGC: Flo Fab Submersible Pumps:
Grinder FGC
Up to 3” solids
Up to 3HP
Over 80’ lift
Up to 61 usgpm

37. Column SEP, SUP Up to 20HP Over 90’ lift Up to 1,000 usgpm
Flo Fab Submersible Pumps:
Column SEP, SUP
Up to 20HP
Over 90’ lift
Up to 1,000 usgpm

38. Accessories for: Flo Fab Submersible Pumps:
Frame & Covers
Floats & High-level alarms
Controls
Foot valves
Basins
Slide Rails

39. Export job 4800 serie pumps

40. 4800 U pump

41. CNC Machining

42. 2600 Pumps in action

43. 4800 Pump

44. Test Facility

45. 2000 Pumps on a jobsite

46. 880RI Pumps

47. Pump assembly line

48. 880RI Export job

49. Work performed in pumping - horsepower

50. Work performed in pumping - horsepower

51. Characteristic curves

52. Characteristic curves