Download presentation
Presentation is loading. Please wait.
Published byDana Dean Modified over 8 years ago
1
Vehicle Monitoring System Michael Jermann Chris Blount Team: 35 TA: Justine Fortier
2
Introduction Improvement on traditional car-alarm systems Uses high-speed cellular networks to: ▫Decrease noise pollution ▫Improve car-alarm effectiveness
3
Key Features Send image to cellular handset via MMS Allow user to remotely activate car alarm operation via SMS Compatible with existing car alarm systems
4
System Overview Microcontroller ▫Arduino Mega 2560 Camera Module ▫C328R GPRS Module ▫Arduino Shield with SIM900 chip Car Alarm Control Circuitry ▫Relay ▫Resistors Power Supply ▫12 V input ▫5V and 3.3 V outputs
5
Block Diagram Car Alarm Control Circuitry Microcontroller Camera GPRS shield Power Supply
6
Microcontroller Overview Arduino Mega 2560 Rev. 3 ▫ATmega2560 Microprocessor ▫4 UARTs ▫54 digital pins ▫4 KB of EEPROM
7
Microcontroller Design
8
Car Alarm Control Circuitry
9
Car Alarm Control Circuitry Overview Original Relay: RZ03-1A4-D012 ▫Contact Rating: 12 VDC, 16 A ▫Input Requirements: 5 VDC, 33 mA ▫Inconsistent operation due to current requirement Switched to SainSmart 5V Relay Module for Arduino ▫Contact Rating: 30 VDC, 10 A ▫Input Requirements: 5 VDC, 20 mA
10
Car Alarm Control Circuitry Design Digital Input 10 – When high, initiate operation Digital Output 11– When high, allow 12VDC signal to reach siren
11
Relay Testing Detect security incursion ▫“OFF” voltage = 0 VDC ▫“ON” voltage = 4.11 VDC Control car alarm operation ▫“OFF” voltage = 0 VDC ▫“ON” voltage = 11.69 VDC
12
Camera
13
Camera Overview C328R ▫3.3v with 60 mA needed ▫UART interface ▫JPEG compression
14
C328R Design Power ▫3.3V from Power Supply GND ▫Ground Tx ▫Rx1 of Arduino Rx ▫Output of voltage divider of Arduino Tx1 ▫(PIC)
15
C328R Testing Arduino Library ▫SYNC ACK ▫Set Baud rate 9600 bps ▫Initial JPEG 128x160 ▫Get Picture
16
GPRS Shield
17
GPRS Overview Shield designed by Seeed Studio for use with Arduino microcontrollers ▫Breakout board for SIM900 GSM/GPRS chipset ▫Insert unlocked SIM card for access to cellular data networks ▫Control operation through “AT” commands through UART ▫Supports SMS/MMS
18
GPRS Software: MMS
19
GPRS Software: SMS
20
GPRS Testing MMS ▫Successfully connect to cellular MMSC within 60 seconds of initialization ▫MMS received by user within 120 seconds of security incursion SMS ▫Relay output activated within 20 seconds of SMS message being sent
21
Power Supply
22
Power Supply Overview TI TPS54383 (First Design) ▫Dual output Buck Converter ▫Design Failed. New chip design for single output. TI LM2576 (Final Design) ▫5V 3A Voltage Regulator ▫Simple buck converter TI LM317T (For added reliability) ▫Linear Regulator ▫5V to 3.3V
23
Power Supply Design LM2576 Courtesy TI LM2576 Datasheet
24
Power Supply Design LM317T Courtesy TI LM317T Datasheet
25
Power Supply Testing
26
Power Supply Efficiency Tested over a resistive load: Input Power ▫192 mW Output Power ▫76.96 mW Efficiency ▫40.0%
27
Power consumption Full system without GPRS powered on ▫169 mA -> 2.03 Watts Full System with GPRS powered on ▫184 mA -> 2.21 Watts Did not meet 100 mA goal
28
Individual Power Consumption Stand alone consumption: Arduino ▫77.7 mA -> 932 mW C328R Camera ▫.67 mA -> 2.2 mW SIM900 GPRS ▫17.9 mA -> 89.5 mW Relay <-Cause of verification failure ▫137.8 mA -> 689 mW
29
Recommendations Implement a more efficient power supply Use a one output relay for greater efficiency Add SD card to Arduino for higher resolution pictures and permanent storage Higher resolution camera
30
Project Synopsis ChallengesSuccesses SIM900 chipset poorly documented Multiple power supply redesigns Camera reliability issues Achieved full system functionality Comfortable with Arduino Generally exceeded performance requirements
31
Ethical Considerations False incrimination ▫Real-time monitoring Privacy Invasion ▫Professional installation required Law Enforcement Surveillance ▫First amendment rights
32
Questions?
Similar presentations
© 2025 SlidePlayer.com. Inc.
All rights reserved.