3. Tynetec manufacture One main type of Pendant Receivers for the Advent xt system: Network Receiver169MHz & 433MHz

4. Network Pendant Receiver 433MHz BNC Connector for aerial IP65 Enclosure 433MHz Receiver Module Reset Switch Network Data Transmit LED Network Data Received LED Power & Network connections 8 Way Dil Switch RX Supply Link (MUST FIT TO 5v)

5. Pendant 433MHz Pendant case is fully sealed (no dil switches) Typical battery life: 5 years or 10,000 activations Fitted with Anti-Strangle cord device

6. Network Pendant Receiver 433MHz - Cabling UP TO 16 Network Receivers can be Fitted to an Advent xt Warden Call system.

7. Network Pendant Receiver 433MHz - Cabling Network Receivers must be located in a position more than 10m from the Control Equipment making sure that aerial cable is free from all other system cabling.

8. Network Pendant Receiver 433MHz - Cabling Network Receivers must be located in Dry secure area (NOT FOR EXTERNAL USE).

9. Network Pendant Receiver 433MHz - Cabling Network Receiver Conduit with system cabling Aerial located in with System cabling DO NOT RUN CABLE THIS WAY

10. Network Pendant Receiver 433MHz - Cabling Network Receiver Conduit with system cabling Aerial free from all system cabling Greater than 10m

11. Network Pendant Receiver 433MHz – Programming/Set Up 8765432187654321 Dil Switches 5, 6, 7 & 8 NOT USED Receiver Address In Binary (Offset by 1)

12. Network Pendant Receiver 169MHz BNC Connector for aerial IP65 Enclosure 169MHz Receiver Module Reset Switch Network Data Transmit LED Network Data Received LED Power & Network connections 8 Way Dil Switch RX Supply Link (MUST FIT TO 5v)

13. Pendant 169MHz Pendant case is fully sealed (no dil switches) Typical battery life: 5 years or 10,000 activations Fitted with Anti-Strangle cord device

14. Network Pendant Receiver 169MHz - Cabling UP TO 16 Network Receivers can be Fitted to an Advent xt Warden Call system.

15. Network Pendant Receiver 169MHz - Cabling Network Receivers must be located in a position more than 3m from the Control Equipment making sure that aerial cable is free from all other system cabling. Network Receivers must be located in Dry secure area (NOT FOR EXTERNAL USE).

16. Network Pendant Receiver 169MHz - Cabling Network Receivers must be located in a position more than 3m away from any DECT Telephone equipment. (This includes Base Stations, Repeaters etc)

17. Network Pendant Receiver 169MHz - Cabling Network Receiver Aerial must be located in a position more than 3m away from the Receiver Unit itself and any DECT Telephone equipment. (This includes Base Stations, Repeaters etc)

18. Network Pendant Receiver 169MHz - Cabling 3M Receiver Ariel Network Receiver 3M DECT Base/Repeater

19. Network Pendant Receiver 169MHz – Programming/Set Up 8765432187654321 Dil Switches 5, 6, 7 & 8 NOT USED Receiver Address In Binary (Offset by 1)

20. Network Pendant Receiver 169MHz & 433MHz – Programming 1. Once Receiver Dil switches are set correctly. 2. Select ‘General Set Up’ in Advent xt programming and change ‘Network Receiver Units’ to the required value. Then click ‘Submit’ to enter any changes.

21. Network Pendant Receiver 169MHz & 433MHz – Programming Neck worn Pendants or any other Radio trigger devices from the Altec range can be allocated to any flat by entering a special code on the Dect telephone. To add Radio triggers:1. Press the Green line key. 2. Wait for the ‘Ready’ prompt. 3. Enter the code 5000 followed by the * (star) key. 4. Wait for the ‘Pendant Enable – Enter Flat’ prompt. 5. Enter the flat number followed by the * (star) key. 6. Activate the pendant (or Altec device) to be added. 7. Wait for the ‘Pendant Enable – Enter Flat’ prompt again. 8. Repeat from step 5 above or press # key to exit the mode. 9. Press the Red line key to clear the connection.

22. Network Pendant Receiver 169MHz & 433MHz – Programming Neck worn Pendants or any other Radio trigger devices from the Altec range can also be deleted from any flat by entering a special code on the Dect telephone. To delete Radio triggers:1. Press the Green line key. 2. Wait for the ‘Ready’ prompt. 3. Enter the code 5001 followed by the * (star) key. 4. Wait for the ‘Pendant Disable – Enter Flat’ prompt. 5. Enter the flat number followed by the * (star) key. 6. Activate the pendant (or Altec device) to be deleted. 7. Repeat from step 3 above or press # key to exit mode. 8. Press the Red line key to clear the connection.

23. Network Pendant Receiver 169MHz & 433MHz – Programming If a Pendant or any other radio device is not available to remove from a flat using code 5001 (i.e it has been lost or become faulty) then all devices for that flat must be deleted. To delete all Radio triggers from Flat:1. Press the Green line key. 2. Wait for the ‘Ready’ prompt. 3. Enter the code 5002 followed by the * (star) key. 4. Wait for the ‘Pendant Disable – Enter Flat’ prompt. 5. Enter the flat number followed by the * (star) key. 6. Press the Red line key to clear the connection.