1. Pressure Governor System Electronics

2. 2 Sentry Pressure Governor System Description The Sentry Pressure Governor System (SPGS) is a J1939 CAN based pressure governing system that consists of a Sentry display, Twister throttle, pressure transducers and associated wiring. Operating on the J1939 network, the Sentry is able to monitor engine RPM and other pertinent data directly from the engine ECU. It has advanced diagnostic features that are unparalleled in the fire service industry. The Sentry display utilizes Class1’s UltraView technology. It is a custom tooled and programmed, 4.3 inch, full color LCD display with 8 buttons.

3. 3 Sentry Pressure Governor System Sentry system components Intake and Discharge Pressure Transducers Harness

4. 4 Vertical Sentry System Kit 599-00010-001 Part NumberDescriptionQuantity per kit 3045-101-00-CL1Vertical Sentry Display1 119970Twister Control Knob (CAN)1 513-00019Sentry System Harness1 122387Bezel1 122482Label1 113557Transducer 0-300 psi2 Horizontal Sentry System Kit 599-00010-002 Part NumberDescriptionQuantity per kit 3045-102-00-CL1Horizontal Sentry Display1 119970Twister Control Knob (CAN)1 513-00019Sentry System Harness1 122387Bezel1 122481Label1 113557Transducer 0-300 psi2 Sentry Pressure Governor System Sentry system part numbers Optional Items 117179Transducer 0-600 psi

5. 5 Sentry Pressure Governor System Sentry connections

6. 6 Sentry Pressure Governor System

7. 7 Sentry Display Features Direct Sunlight Visible Sealed to IP67 Front and Rear J1939 or Analog Engine Control Flexible Mounting Options Vertical or Horizontal Orientation Multilingual Check engine warning Stop engine warning Advanced diagnostics

8. 8 Sentry Pressure Governor System

9. 9 Twister features Clockwise or Counter-Clockwise operation Sealed to IP67 Large Ergonomic knob for control Large idle button for easy use with gloved hand Interlock and active status LED’s J1939 CAN communication

10. 10 Sentry Pressure Governor System General System Features Mount display at eye level and Twister at hand level for the best ergonomic operation Target pressure indication Advanced diagnostics Multi – Station control Multilingual Most visible display in the industry Advanced cavitation and water supply operation Static or pressurized water source routines

11. 11 Sentry Pressure Governor System Sentry System Features CAN BUS Multi Station Control Master Sentry Slave Sentry Intake and Discharge Transducers required only on Master Sentry system

12. 12 Sentry Pressure Governor System Water supply and cavitation features MessageDescriptionSentry ResponseOperator Action INTAKE SENS DISCHG SENS Signal voltage from the discharge or intake pressure sensor is less than +0.30VDC or greater than +4.90VDC. SENTRY switches to THROTTLE mode operation. Operator may continue to use SENTRY in THROTTLE mode. Operator should have the discharge and/or intake pressure sensor and associated wiring verified. ∆ PSI LIMIT Pump discharge pressure increased 50 PSI over the pressure point detected when the operator set the desired engine RPM (while in throttle mode). SENTRY maintains THROTTLE mode operation but limits the engine RPM to maintain no more than a 50 PSI differential over the pressure detected when the operator set the desired engine RPM. No operator action required. Operator may continue to use SENTRY in THROTTLE mode.

13. 13 Sentry Pressure Governor System Water supply and cavitation features MessageDescriptionSentry ResponseOperator Action WATER SUPPLY Pump discharge pressure decreased as RPM was increased (while in pressure mode). SENTRY reduces engine speed to 1100 RPM and attempts to increase discharge pressure by ramping engine RPM. Operator should verify water supply or change to THROTTLE mode. OPERATOR CMD Pump intake pressure loss. Discharge pressure dropped below 30 PSI. SENTRY maintains engine speed at 1100 RPM for the configured pressure time- out (5.6.8). Operator should verify water supply or change to THROTTLE mode.

14. 14 MessageDescriptionSentry ResponseOperator Action LOW PRESSURE Pump discharge pressure was greater than 50 PSI, but has dropped below 30 PSI. SENTRY switches to STANDBY mode and the engine RPM reduced to IDLE. Operator should verify water supply. ∆ RPM LIMIT Engine RPM increase to compensate for a drop in pressure was not able to recover to the pressure set point (while in pressure mode). SENTRY maintains the limit RPM. Operator should check for pump pressure capability. Sentry Pressure Governor System Water supply and cavitation features

15. 15 Sentry Pressure Governor System Sentry diagnostics The Sentry Pressure Governor System has the most advanced diagnostics of any pressure controller on the market. It provides two levels of diagnostics. One for the operator and one for the maintenance technician. It’s like having the manual with the part at all times.

16. 16 Sentry Pressure Governor System Sentry diagnostics Sample transducer fault condition.

17. 17 OEM Interlock Fault Throttle Ready Interlock Fault Sentry Fault Screens

18. 18 Coolant Temperature Fault Oil Pressure Fault Sentry Fault Screens

19. 19 Twister Communication Fault Analog Voltage Fault

20. 20 Low Voltage Warning Sentry Fault Screens