Download presentation
Presentation is loading. Please wait.
Published byBennett Lane Modified over 8 years ago
1
Status of Hybrid target R&D at KEK-LINAC T.Takahashi Hiroshima University 06 Se0temer 2012 POSIPOL2012 DESY Zeutzen Collaborators: V. Strakhovenko O. Dadoun, R. Chehab, A.Variola, L. Rinolfi, O. Dadoun,T.Kamitani, T.Suwada, T.Omori, J.Urakawa,K.Furukawa, K.Umemori,M.Satoh,T.Sugimura,S.Kawada, T.Akagi, Y. Uesugi
2
Contents Status of previous experiments Temperature measurement 2012 January Prospects
3
Hybrid target for positron source A away to reduce thermal load in positron targets – proposed by Chehab, Variola, Strakhovenko -> Experimental study to – accumulate data on e+ yields, heat deposit,,, Feasibility as a positron source for LCS e-e- e +, e -, g e-e- e+e+ e+e+
4
experimental site KEKB LINAC Switch yard 8 GeV e- ~ nc/bunch upto 25Hz single bunch After the earthquake: beam recovered to 3GeV 8 GeV operation expected later half of 2012
5
Setup 8GeV e-1mm W crystal Sweeping Magnet 0.96T 0.75m amorphous W 8 mm 18 mm Analyzing magnet 5 ~ 30MeV
6
pictures e- 8GeV W Crystal on the goniometer Sweeping magnet
7
pictures movable stage amorphous targets thermocoupoles attached back end
8
The data Hybrid Conventional e 8GeV sweep mag 1mm W Crystal on axis (aligned to the beam) off axis (not aligned to the beam ) e 8GeV amorphous W 1.75, 3.5, 5.25, 8, 18mm temperature at the end of the targets by thermocouples and infrared camera positrons from the target momentum analyzed
9
positron yield (arb. unit) angle of crystal axis w.r.t. beam (mr) rot. in vertical plain e sweep mag 8 mm Rocking curve same for horizontal rotation Preliminary factor 3 enhancement
10
e+ yield amorphous thickness [mm] e+ detected [a.u] P=20MeV Need simulation for analyzing the magnet collimator, detector to evaluate e+ yeilds
11
Detector acceptance Simulation of the is in progress by Y.Uesugi
12
simulation in progress Very Preliminary low acceptance 0.0005e+/e- takes time for simulation Target Thickness (mm) e+ yield (A.U)
13
Temperature measurement w/ thermocouples back plane of amorphous target thermocouple approximately 1mm x 1mm to fast data logger read temperature each 10ms bunch by bunch temperature variation PEDD information by thermocouple temperature at equilibrium total energy deposit
14
Example of Temperature Measurement Temperature of the 8mm amorphous target for the hybrid case Time from Beam On (Minutes) Temperature (degree Celsius) Base temp. 23.3 ℃ T ~ 32 ℃ Preliminary
15
T vs total energy deposit hybrid on axis conventional 18mm 8mm T at equilibrium has information for total energy deposit except for 18mm hybrid target is thicker than shower max hybrid off axis T at equilibrium (deg) (simulation) (measured)
16
bunch by bunch temp. dT provides a measure of PEDD hybrid on axis conventional hybrid off axis Simulation Measured
17
Making thermo couple array thermocouples temperature distribution of amorphous target bunch by bunch bases design in progress at Hiroshima
18
temperature measurement January 2012
19
temperature measurement
20
e+(accepted) v.s. PEDD ~G4 Simulation~ e- =2.5mm e- =4.0mm hybrid (5GeV 8GeV) =2.5mm e+ = 1.1pedd e- =1.0mm hybrid (5GeV 8GeV) =1.0mm
21
e+(accepted) v.s. PEDD ~G4 Simulation~ e- =2.5mm e- =4.0mm hybrid (5GeV 8GeV) =2.5mm e+ = 1.1pedd e- =1.0mm hybrid (5GeV 8GeV) =1.0mm Verification of this plot is a purpose of this experiment, but if it is the case; A hybrid works, why not a conventional
22
summary Systematic data for hybrid target R&D – yield from various target thickness, momentum – G4 Simulation in progress energy deposit/temperature – Thermocouple array works – in progress. G4 simulation is ready. – Systematic data in next experiments – ( but we need to wait for full recovery of KEKB LINAC)
Similar presentations
© 2025 SlidePlayer.com. Inc.
All rights reserved.