1. Date of download: 6/1/2016 Copyright © ASME. All rights reserved. From: Statistical Tolerance Allocation for Tab-Slot Assemblies Utilizing Tolerance-Maps J. Comput. Inf. Sci. Eng. 2010;10(1):011005-011005-13. doi:10.1115/1.3249576 The adjoined four-dimensional T-Maps for tabs and slots that are to be engaged in an assembly and are made to the specifications in Fig.. The common VC-size is 10.0 mm at vertex σ5. Figure Legend:

2. Date of download: 6/1/2016 Copyright © ASME. All rights reserved. From: Statistical Tolerance Allocation for Tab-Slot Assemblies Utilizing Tolerance-Maps J. Comput. Inf. Sci. Eng. 2010;10(1):011005-011005-13. doi:10.1115/1.3249576 A slot made to give a clearance c′ with the tab-gauge. The clearance boundary and the corresponding clearance-zone c′ of height tin−2c′ for a slot cut in Part 2 (Fig. ). The VC-size (Figs. ) is the 10.0 mm size of the gauge-tab used to measure the position of the slot. Figure Legend:

3. Date of download: 6/1/2016 Copyright © ASME. All rights reserved. From: Statistical Tolerance Allocation for Tab-Slot Assemblies Utilizing Tolerance-Maps J. Comput. Inf. Sci. Eng. 2010;10(1):011005-011005-13. doi:10.1115/1.3249576 Relative frequency distribution (PDF) of clearance when the variations arise only from position of the medial-plane of the slot. Constructed from the tolerances in Fig. : 0≤c≤tin/2. Figure Legend:

4. Date of download: 6/1/2016 Copyright © ASME. All rights reserved. From: Statistical Tolerance Allocation for Tab-Slot Assemblies Utilizing Tolerance-Maps J. Comput. Inf. Sci. Eng. 2010;10(1):011005-011005-13. doi:10.1115/1.3249576 Comparison of the PDFs for clearance for the slot in Fig. when MMC is applied and when it is not (RFS). Constructed from the tolerances in Fig. : 0≤c≤(tin+τin)/2. Figure Legend:

5. Date of download: 6/1/2016 Copyright © ASME. All rights reserved. From: Statistical Tolerance Allocation for Tab-Slot Assemblies Utilizing Tolerance-Maps J. Comput. Inf. Sci. Eng. 2010;10(1):011005-011005-13. doi:10.1115/1.3249576 A notional representation of the adjoined 4D Tolerance-Maps in Fig.. The shaded regions are the hypersurfaces S for the tab (left) and slot (right), placed such that clearance contribution c′in for the slot is zero. The 3D bases of the hyperpyramids have been shown notionally in two dimensions so as to make the intent of the shadings more apparent. Figure Legend:

6. Date of download: 6/1/2016 Copyright © ASME. All rights reserved. From: Statistical Tolerance Allocation for Tab-Slot Assemblies Utilizing Tolerance-Maps J. Comput. Inf. Sci. Eng. 2010;10(1):011005-011005-13. doi:10.1115/1.3249576 Geometrical representation of computation of the frequency distribution of c′ as the joint frequency distribution of cex and cin. Note that f1 and f2 are identical distributions here only because the same tolerances are used in Figs.. Figure Legend:

7. Date of download: 6/1/2016 Copyright © ASME. All rights reserved. From: Statistical Tolerance Allocation for Tab-Slot Assemblies Utilizing Tolerance-Maps J. Comput. Inf. Sci. Eng. 2010;10(1):011005-011005-13. doi:10.1115/1.3249576 Comparison of PDFs of clearance for engagement of tabs and slots when MMC is applied and MMC is not applied, i.e., RFS. Constructed from the tolerances in Fig. ; 0≤c≤(tex+τex+tin+τin)/2. Figure Legend:

8. Date of download: 6/1/2016 Copyright © ASME. All rights reserved. From: Statistical Tolerance Allocation for Tab-Slot Assemblies Utilizing Tolerance-Maps J. Comput. Inf. Sci. Eng. 2010;10(1):011005-011005-13. doi:10.1115/1.3249576 Comparison of PDFs of one-dimensional clearance for engagement of gauge-tab and slot and gauge pin-and-hole. The variations arise only from position-variations (position tolerance 0.5 mm) of the medial-plane (for the slot) and axis (for the hole). The corresponding tab and the pin are considered as gauges. Figure Legend:

9. Date of download: 6/1/2016 Copyright © ASME. All rights reserved. From: Statistical Tolerance Allocation for Tab-Slot Assemblies Utilizing Tolerance-Maps J. Comput. Inf. Sci. Eng. 2010;10(1):011005-011005-13. doi:10.1115/1.3249576 Comparison of PDFs of one-dimensional clearance for engagement of tab and slot and pin-and-hole. The variations arise from position-variations (position tolerance 0.5 mm) and size-variation (0.5 mm) of the slot and the hole. The tab and the pin are considered as gauges of VC-sizes. Figure Legend: