1. EL4060 智慧行動裝置控制應用實習 Smart Mobile Device Control Application Laboratory 數位家庭整合應用平台介紹與應用 Presenter ： Che-Hao Chang 助教：張哲豪 1

2. Outline 1.Relay 2.Power Meter 2

3. 3 1.Relay

4. Equipment and Components 4 Android OS computer Apps in Android OS computer UART Cable Power Supply adaptor Connect to computer Cable ZigbBee_Config..

5. Equipment and Components 5 Function: Control all other sensor components above Main Controller Function: Control switch to turn on and off Relay

6. 6 Step 1: Connecting

7. 7 UART cable connect with Android Computer Must supply 5V power to turn on Step 1: Connecting

8. 8 Make sure it connect with third port Plug in 5V power supply Plug in UART Step 1: Connecting

9. 9 2. If Success read the sensor 1.Click here 3. Else you will see this Step 2: Server

10. 10 1.Choose which type of devices you going to burn 主 : Main Controller 传感器 : Sensor 继电器 : Relays controller 2. PAD ID is the server to show your devises which address to go. The coding depend on your devices, the example below is 00-07: 3. Make sure is Channel 14 and number 6 Step 2: Server

11. 11 4. Sending address: For Main: 10-28 For Sensor: 10-15 5. Receiving address: For Main: 10-15 Caution: Please double check, if wrong, you won’t see anything happen Last Step, click here to close. Caution: You must click here because it will just burn after you close it. Step 2: Server

12. 12 This is when you choose 继电器 (Relay)what it will display For relay, we have to set this part. This part is to let main controller recognize all the relay. Step 2: Server

13. 13 Sensor no need send any information to main controller, thus it no need sending address Caution: this address must according your main controller sending address Step 2: Server

14. 14 When you done the last step, the sensor LED will start blinking. Make sure UART is plugged in the middle port Step 2: Server

15. 15 Detector’s result Relays controller Step 3: Test

16. 16 If your main controller plug in and nothing had detect, it might be few problem: 1.There is no data transferring between your main controller and your sensor. 2.Plug in wrong port 3.You haven't plug in your sensor. Precaution

17. 17 2.Power Meter

18. 18 Power Meter Function: Measure Voltage, Current and Power Calculate the price of energy used Control switch to turn on or off Equipment and Components

19. 19 Function: Receive data in wireless and send to computer ZigBee wireless data transfer Function: Receive data in wireless and send to phone using Bluetooth. Bluetooth controller On off pin Equipment and Components

20. 20 Using ZigBee wireless transfer data Connect to 5v USB power supply Connect to UART Make sure it connect with first port Step 1: Connecting

21. 21 Using ZigBee wireless transfer data Click this to activate Step 2: Open Android App

22. 22 After you click inside each one, it will display this page. If you are going to control it, the last setting will be the one you need to click. Step 3: Test

23. 1. 封面 ( 班級、學號、姓名、教師...) 2. 實驗步驟結果 ( 貼圖片並簡略說明 ) 3. 心得感想 4. 一組繳交一份報告即可，下次上課時統一交給助教 實驗報告 23

24. 注意 4 月 7 日 --- 放假 4 月 14 日 --- 停課 4 月 21 日 --- 下次上課時間 24