1. copyright ⓒ ECOSIAN. All right reserved. Biogas Purification and Compression System Training Program in Kathmandu University January 03, 2010 Dharma K.C

2. page 2 copyright ⓒ ECOSIAN. 2008 All right reserved. 1. Project idea 2. Equipment drawing 3. Description of equipment 4. Brief information on PSA 5. Energy balance 6.Brief information on PLC Contents 7.Equipment layout

3. page 3 copyright ⓒ ECOSIAN. All right reserved. Basic idea of the project

4. page 4 copyright ⓒ ECOSIAN. All right reserved. Piping & Equipment Diagram

5. page 5 copyright ⓒ ECOSIAN. All right reserved. Construction of bio-digesters Site: Kathmandu University Size: 90 m3 (30 *3) Scale: Pilot Project

6. page 6 copyright ⓒ ECOSIAN. All right reserved. Bio-gas generation Feeding Materials: Any kind of bio-degradable solid waste Flow Rate: ~18 m3/day, Pressure: 1 bar Composition: ~ 50% CH4, ~ 48% CO2, ~1% H2S and ~1% others Feeding Materials

7. page 7 copyright ⓒ ECOSIAN. All right reserved. Description of equipment H2S Remover 1. It consists of changeable H2S filter 2. While the amount of H2S attached to the filter increases, the pressure shown in the pressure gauge also increases 3. Once filter is fully saturated, it needs to be replaced. 4. H2S should be removed completely as it causes corrosion on the wall of vessels used.

8. page 8 copyright ⓒ ECOSIAN. All right reserved. Description of equipment Biogas compressor Specification Type: Oil-free piston Design Pressure: 15 bar Design temp: 50 degree centigrade Material: Mild Steel Flow rate: 100L/min Power 380VAC 3 phase 50Hz (0.374kWh) Function: To compress the biogas coming out of H2S filter and increase the pressure up to 2~3 bar which is required for PSA system.

9. page 9 copyright ⓒ ECOSIAN. All right reserved. Specification: Type: Vertical Cylinder DP/DT: 15 bar/ 50 degree C Volume: 30 L Function: Collect slightly compressed gas before sending to the purifier (PSA) It maintain continuous flow of gas to the purifier It prevents from popping and irregular strike of bio gas to purifier. CNG buffer drum Description of equipment

10. page 10 copyright ⓒ ECOSIAN. All right reserved. Description of equipment Scrubber (Pressure Swine Adsorption Type) First Filter Second Filter Adsorption Columns

11. page 11 copyright ⓒ ECOSIAN. All right reserved. Description of Equipment CNG regulator fitted in adsorption column It maintains the pressure and flow rate of gas in adsorption column Functioning condition and data can be seen in the graphic board of control panel. Simultaneous falling and increasing of pressure and flow rate occurs during alternating cycles namely adsorption, regeneration and pressure build-up

12. page 12 copyright ⓒ ECOSIAN. All right reserved. Description of Equipment Specification: Type: Oil rotary Flow rate: 200L/min Power: 220VAC 1 phase 50Hz 0.034kWh Material: Mild Steel Function: to pump out CO2 and N2 from adsorption columns and maintain the pressure Vacuum pump

13. page 13 copyright ⓒ ECOSIAN. All right reserved. PSA system linking with PLC Electric circuit and signal transfer It receive signals from all devices of purifier and transfer it to the control panel. Digital signals can be seen in PLC system and operation condition can be observed by the notification of LED (light) in the graphic board.

14. page 14 copyright ⓒ ECOSIAN. All right reserved. Installation of equipment

15. page 15 copyright ⓒ ECOSIAN. All right reserved. Inner circuit of control panel

16. page 16 copyright ⓒ ECOSIAN. All right reserved. Graphic Board Operation of each equipment can be seen by the red light adjacent to drawing of equipment as well as in monitor of PLC system.

17. page 17 copyright ⓒ ECOSIAN. All right reserved. Chemical process Adsorption is the process that happens when a gas or liquid solute gets accumulated on the surface of a solid or, sometimes, a liquid (adsorbent), forming in the process a molecular or atomic film (known as adsorbate). Separation of CO2 from CH4 is generally done by adsorption/desorption of carbon dioxide on beds of activated carbon (in our case) or zeolites at different levels of pressure. Adsorption in brief The term adsorption refers and encompasses both processes, while the reverse process is known as desorption. Pressure Swing Adsorption (PSA) is a technology used to separate some gas species from a mixture of gases under pressure according to the species molecular characteristics and affinity for an adsorbent material.

18. page 18 copyright ⓒ ECOSIAN. All right reserved. Application of Activated Carbon in PSA Large number of gases are separated using activated carbon as the adsorbent material. Slightly above the atmospheric pressure, the activated carbon preferentially adsorbs the impurities like non-methane. Pressure Swing Adsorption (PSA) is a technology used to separate some gas species from a mixture of gases under pressure according to the species molecular characteristics and affinity for an adsorbent material. In a normal operation each adsorber operates in the following alternating cycles namely adsorption, regeneration and pressure build-up.

19. page 19 copyright ⓒ ECOSIAN. All right reserved. PSA for Biogas Upgrading While passing through the adsorber vessel, carbon dioxide, oxygen and nitrogen gets adsorbed on to the surface of the adsorbent material. The gas that exits from the top of the adsorber vessel contains around 97% of Methane.

20. page 20 copyright ⓒ ECOSIAN. All right reserved. Compressor and storage tank Function of Compressor: To compress the gas after scrubbing Pure methane, before compression, is collected in the Buffer Drum to make the continuous supply without popping. Function of Storage tank: It is the heaviest among all equipment. It collects compressed gas of pressure230 bar and its size is 585L.

21. page 21 copyright ⓒ ECOSIAN. All right reserved. Dispenser Gas contain in high pressure in the storage tank will be filled in CNG cylinders. There will be three types of cylinders of different size. One is for vehicular use (64L) and other are of commercial purpose (46.7L and 40.2L). There are alternative system and safety measures to fill two type of cylinders

22. page 22 copyright ⓒ ECOSIAN. All right reserved. Energy Balance

23. page 23 copyright ⓒ ECOSIAN. All right reserved. Brief information on PLC PLC: Programmable logic controller is a digital computer used for automation of electromechanical processes, such as control of machinery on factory assembly lines, amusement rides, or lighting fixtures. Unlike general-purpose computers, the PLC is designed for multiple inputs and output arrangements, extended temperature ranges, pressure, flow rate, and resistance to vibration and impact. A PLC is an example of a real time system since output results must be produced in response to input conditions within a bounded time, otherwise unintended operation will result. PLC & Input Output arrangement

24. page 24 copyright ⓒ ECOSIAN. All right reserved. Equipment layout

25. Thank you for your kind attention copyright ⓒ ECOSIAN. All right reserved. Ecosian Co. Ltd. Tel 82-70-7725-7576 Fax 82-2-890-7562 www.ecosian.com kcdharma@ecosian.com