1. Quick Start Guide ST30/ST32 Series mobile computer

2. Features front and side views 2 6 3 4 5 7 8 9 9 1 1.Power button 2.LCD DISPLAY 3.Status LED 4.Charging LED 5.Bottom trigger button 6.Scan / Action button 7.Earphone 8.Micro USB Connector 9.Battery cover

3. Features rear, top and bottom views 5 7 6 3 2 1 8 1.Data capture window 2.Flash 3.Camera 4.Label recess 5.Speaker 6.Handstrap clip 7.Battery cover 8.Handstrap bar 4

4. Getting started installing SD and SIM card Installing MicroSD card 1.Remove battery if necessary 2.Insert MicroSD card into the card slot 3.Make sure the card connector (the golden contacts) should be at the front of insert Installing SIM card 1.Remove battery if necessary 2.Insert SIM card into the SIM card slot 3.Make sure the SIM card connector (the golden contacts) should be at the front of insert Installing PSAM card 1.Remove battery if necessary. 2.Unlock the PSAM card lock. 3.Insert PSAM card into the SIM card slot 4.Make sure the SIM card connector (the golden contacts) should be at the front of insert 5.Lock the PSAM card slot. PSAM card

5. Installing battery 1.Lift up battery cover slightly, grasp the battery cover and remove it 2.Insert the battery, upper (with golden contacts) first, into the battery compartment 3.Press the battery down until the battery fully rests on the bottom of battery compartment 4.Put the battery cover back, tab first, and press down until the latch secure the battery cover Removing battery 1.Lift up the battery cover slightly, grasp the battery cover and remove it 2.Remove the battery, use the right side first, from the battery compartment Getting started installing & removing battery 2 2 3

6. Getting started cradling and charging Charging the device by power adapter 1.Insert the small end of power adapter into the Micro USB jack 2.Plug the large end of power adapter into a power outlet 3.Charging status LED on device Green LED = charged over 90% Red LED = charging Important notes 8 hours is recommended for the 1 st time charging. Recharge of 3150mAh will take 4-5 hours for 80% battery capacity.

7. Installing handstrap 1.Remove screws from handstrap holder. 2.Separate the velcro of the handstrap. 3.Feed the loose end of the extended handstrap through the handstrap clip 4.Wrap the handstrap around the clip and fasten together to close the strap 5.Install the screws back to handstrap holder. Getting started

8. Getting started Enabling & disabling WiFi Enabling WiFi 1.Tap Apps icon, then select Settings 2.Go to Network connections, turn on WiFi 3.Tap the WiFi text on the setting screen 4.A list of WiFi networks appears, pick the desired AP and setup as the wireless AP properties as usual Disabling WiFi 1.Tap Apps icon, then select Settings 2.Go to Network connections, turn off WiFi

9. Getting started Enabling & disabling BT Enabling Bluetooth 1.Tap Apps icon, then select Settings 2.Go to Network connections, turn on Bluetooth 3.Tap the Blyetooth text on the setting screen 4.A list of bluetooth devices appears, pick the desired device to pair up Disabling Bluetooth 1.Tap Apps icon, then select Settings 2.Go to Network connections, turn off Bluetooth

10. Enabling GPS 1.Tap Apps icon, then select Settings 2.Select Location services 3.Select Use GPS satellites Disabling GPS 1.Tap Apps icon, then select Settings 2.Select Location services 3.Deselect Use GPS satellites Getting started Enabling & disabling GPS

11. Getting started VPN checking VPN checking 1.Tap Apps icon, then select Settings 2.Select More networks 3.Select Mobile networks, check whether mobile network is turned on 4.Select Network operator, check if it shows correct carrier

12. Performing reboot 1.Long press power button 2.A menu appears, keep to hold the power key until the device reboot Performing factory data reset 1.Tap Apps icon, then select Settings 2.In Personal section, select Back up and reset 3.Select Factory data reset, click Reset phone Getting started reboot and factory data reset

13. Refreshing ST30/ST32 ROM 1.Copy ST30/ST32 ROM zip file to the root directory of the microSD card 2.Open the battery cover, remove the battery 3.Insert the microSD card 4.Install the battery to the battery compartment 5.Press and hold the power button and the left side scan button for few seconds 6.Continue to press and hold the left scan button and power button until the update screen appears 7.Press power button, update menu appears. 8.Use left side scan button to select update from SD card, press the bottom trigger button to confirm 9.Select the update file from SD card, press bottom trigger button to confirm 10.After complete installation, select wipe factory reset, press bottom trigger button to confirm Getting started Refreshing ROM 5 5 8 10 7

14. Getting started Refreshing ROM 11. Select Yes – delete all us, press enter 12. Finally select “reboot system now” to reboot the device 11

15. Getting started Enabling scanner Enabling scanner 1.Remove the scanner film on the scanner window 2.Tap Apps icon, then select ScanDemo 3.Press the scanner button on the device to scan the barcode 4.Barcode data will be shown on the screen Scan button

16. 65 o Getting started Capturing data 65 o

17. Battery safety guidelines 1.Use manufacturer's original battery and charger only. Any incompatible battery or charger may result in a fire, explosion, or other hazard. 2.Do not disassemble or open, crush, bend or deform, puncture, or shred the battery. 3.Do not short-circuit a battery by allowing conductive materials to contact the battery terminals. 4.Do not immerse or expose the battery to water or other liquids. 5.Do not dispose of batteries in fire or place the battery into a microwave oven or dryer. 6.If battery leakage is found, avoid the liquid to come in contact with the skin or eyes. 7.If contact has been made, rinse the affected area with water and seek medical advice. 8.If you suspect damage to your equipment or battery, contact the manufacturer for inspection. 9.Follow the local regulations to dispose or recycle the used re-chargeable batteries. Getting started Battery warning