Presentation is loading. Please wait.

Presentation is loading. Please wait.

Lesson 1 Friction Chart Primer 1.3 Friction Chart.

Published byAnn Washington Modified over 8 years ago

Similar presentations

Presentation on theme: "Lesson 1 Friction Chart Primer 1.3 Friction Chart."— Presentation transcript:

1 Lesson 1 Friction Chart Primer 1.3 Friction Chart

2 What happens if there are less than 100 ft of Duct? ? ? ?

3 What happens if there are less than 100 ft. of Duct? The duct size will work and the duct system will operate efficiently and quietly. However, the formula may be used to decrease the size of the duct so the designed total equivalent Length is the same throughout the duct system.

4 What happens if there are more than 100 ft of duct? ? ? ?

5 The duct size will not work and the duct system will not operate efficiently and quietly.

6 What happens if there are more than 100 ft of duct? The duct size will not work and the duct system will not operate efficiently and quietly. Formula: Friction Loss = SDP x 100 ÷ TEL of Duct Where: SDP = System Design Pressure TEL = Total Equivalent Length of Duct

7 Example: For a 150 CFM output, the TEL is 200 ft. and the system design pressure is 0.3, what would the friction Loss be? Friction Loss = SDP x 100 ÷ TEL of Duct Friction Loss = 0.3 x 100 ÷ 200 = 0.15

8 Example: For a 150 CFM output, the TEL is 200 ft. and the system design pressure is 0.3, what would the friction loss per 100 ft. be? Friction Loss = SDP x 100 ÷ TEL of Duct Friction Loss = 0.3 x 100 ÷ 200 = 0.15 Thus, to actually allow 150 CFM to pass through, the duct would have to be designed for a 0.15 friction loss

9 The Friction Chart can use the adjusted friction rate and CFM to select the required duct size: CFM = 150 Friction Rate = 0.15

10 The Friction Chart can use the adjusted friction rate and CFM to select the required duct size: CFM = 150 Friction Rate = 0.15 7” duct is the size that meets this requirement

11 The Friction Chart can use the adjusted friction rate and CFM to select the required duct size: CFM = 150 Friction Rate = 0.15 7” duct is the size that meets this requirement

12 Is There an easy way to Convert System Design Pressures for Total Equivalent Lengths? ? ? ?

13 Equivalent Length of Duct (ft) TOTAL PRESSURE DROP IN DUCT (In. of water column) 0.050.070.100.150.200.250.300.400.50 35-440.130.180.250.380.500.630.751.001.25 45-540.100.140.200.300.400.500.600.801.00 55-640.080.120.170.250.330.420.500.670.83 65-740.070.100.140.210.290.360.430.570.72 75-840.060.090.130.190.250.310.380.500.63 85-940.060.080.110.170.220.280.330.450.56 95-1040.050.070.100.150.200.250.300.400.50 105-1140.050.060.090.140.180.230.280.370.46 115-1290.040.060.080.120.170.210.250.330.42 130-1490.040.050.070.110.140.180.210.290.36 150-1690.030.040.060.090.130.160.190.250.31 170-1890.030.040.060.080.110.140.170.220.28 190-2140.030.040.050.080.100.130.150.200.25 215-2390.020.030.050.070.090.110.130.180.22 240-2640.020.030.040.060.080.100.120.160.20 265-2890.020.030.040.050.070.090.110.150.18 290-3240.020.03 0.050.070.080.100.130.17 325-3740.02 0.030.040.060.070.090.110.14 375-4240.010.020.030.040.050.060.080.100.13 425-4740.010.020.03 0.050.060.070.090.11 475-5240.010.02 0.030.040.050.060.080.10 525-5740.01 0.020.030.040.050.060.070.09 575-6250.01 0.020.03 0.040.050.070.08 Table for Converting System Design Pressure (total pressure drop in the duct) and Total Equivalent Length of Duct to Friction Loss

14 Equivalent Length of Duct (ft) TOTAL PRESSURE DROP IN DUCT (In. of water column) 0.050.070.100.150.200.250.300.400.50 35-440.130.180.250.380.500.630.751.001.25 45-540.100.140.200.300.400.500.600.801.00 55-640.080.120.170.250.330.420.500.670.83 65-740.070.100.140.210.290.360.430.570.72 75-840.060.090.130.190.250.310.380.500.63 85-940.060.080.110.170.220.280.330.450.56 95-1040.050.070.100.150.200.250.300.400.50 105-1140.050.060.090.140.180.230.280.370.46 115-1290.040.060.080.120.170.210.250.330.42 130-1490.040.050.070.110.140.180.210.290.36 150-1690.030.040.060.090.130.160.190.250.31 170-1890.030.040.060.080.110.140.170.220.28 190-2140.030.040.050.080.100.130.150.200.25 215-2390.020.030.050.070.090.110.130.180.22 240-2640.020.030.040.060.080.100.120.160.20 265-2890.020.030.040.050.070.090.110.150.18 290-3240.020.03 0.050.070.080.100.130.17 325-3740.02 0.030.040.060.070.090.110.14 375-4240.010.020.030.040.050.060.080.100.13 425-4740.010.020.03 0.050.060.070.090.11 475-5240.010.02 0.030.040.050.060.080.10 525-5740.01 0.020.030.040.050.060.070.09 575-6250.01 0.020.03 0.040.050.070.08 A duct has a SDP of 0.3 in. water column and a TEL of 191 ft. Find the friction loss using The table below:

15 Equivalent Length of Duct (ft) TOTAL PRESSURE DROP IN DUCT (In. of water column) 0.050.070.100.150.200.250.300.400.50 35-440.130.180.250.380.500.630.751.001.25 45-540.100.140.200.300.400.500.600.801.00 55-640.080.120.170.250.330.420.500.670.83 65-740.070.100.140.210.290.360.430.570.72 75-840.060.090.130.190.250.310.380.500.63 85-940.060.080.110.170.220.280.330.450.56 95-1040.050.070.100.150.200.250.300.400.50 105-1140.050.060.090.140.180.230.280.370.46 115-1290.040.060.080.120.170.210.250.330.42 130-1490.040.050.070.110.140.180.210.290.36 150-1690.030.040.060.090.130.160.190.250.31 170-1890.030.040.060.080.110.140.170.220.28 190-2140.030.040.050.080.100.130.150.200.25 215-2390.020.030.050.070.090.110.130.180.22 240-2640.020.030.040.060.080.100.120.160.20 265-2890.020.030.040.050.070.090.110.150.18 290-3240.020.03 0.050.070.080.100.130.17 325-3740.02 0.030.040.060.070.090.110.14 375-4240.010.020.030.040.050.060.080.100.13 425-4740.010.020.03 0.050.060.070.090.11 475-5240.010.02 0.030.040.050.060.080.10 525-5740.01 0.020.030.040.050.060.070.09 575-6250.01 0.020.03 0.040.050.070.08 A duct has a SDP of 0.3 in. water column and a TEL of 191 ft. Find the friction loss using The table below:

16 Equivalent Length of Duct (ft) TOTAL PRESSURE DROP IN DUCT (In. of water column) 0.050.070.100.150.200.250.300.400.50 35-440.130.180.250.380.500.630.751.001.25 45-540.100.140.200.300.400.500.600.801.00 55-640.080.120.170.250.330.420.500.670.83 65-740.070.100.140.210.290.360.430.570.72 75-840.060.090.130.190.250.310.380.500.63 85-940.060.080.110.170.220.280.330.450.56 95-1040.050.070.100.150.200.250.300.400.50 105-1140.050.060.090.140.180.230.280.370.46 115-1290.040.060.080.120.170.210.250.330.42 130-1490.040.050.070.110.140.180.210.290.36 150-1690.030.040.060.090.130.160.190.250.31 170-1890.030.040.060.080.110.140.170.220.28 190-2140.030.040.050.080.100.130.150.200.25 215-2390.020.030.050.070.090.110.130.180.22 240-2640.020.030.040.060.080.100.120.160.20 265-2890.020.030.040.050.070.090.110.150.18 290-3240.020.03 0.050.070.080.100.130.17 325-3740.02 0.030.040.060.070.090.110.14 375-4240.010.020.030.040.050.060.080.100.13 425-4740.010.020.03 0.050.060.070.090.11 475-5240.010.02 0.030.040.050.060.080.10 525-5740.01 0.020.030.040.050.060.070.09 575-6250.01 0.020.03 0.040.050.070.08 A duct has a SDP of 0.3 in. water column and a TEL of 191 ft. Find the friction loss using The table below: Thus, the duct size will be larger

17 Equivalent Length of Duct (ft) TOTAL PRESSURE DROP IN DUCT (In. of water column) 0.050.070.100.150.200.250.300.400.50 35-440.130.180.250.380.500.630.751.001.25 45-540.100.140.200.300.400.500.600.801.00 55-640.080.120.170.250.330.420.500.670.83 65-740.070.100.140.210.290.360.430.570.72 75-840.060.090.130.190.250.310.380.500.63 85-940.060.080.110.170.220.280.330.450.56 95-1040.050.070.100.150.200.250.300.400.50 105-1140.050.060.090.140.180.230.280.370.46 115-1290.040.060.080.120.170.210.250.330.42 130-1490.040.050.070.110.140.180.210.290.36 150-1690.030.040.060.090.130.160.190.250.31 170-1890.030.040.060.080.110.140.170.220.28 190-2140.030.040.050.080.100.130.150.200.25 215-2390.020.030.050.070.090.110.130.180.22 240-2640.020.030.040.060.080.100.120.160.20 265-2890.020.030.040.050.070.090.110.150.18 290-3240.020.03 0.050.070.080.100.130.17 325-3740.02 0.030.040.060.070.090.110.14 375-4240.010.020.030.040.050.060.080.100.13 425-4740.010.020.03 0.050.060.070.090.11 475-5240.010.02 0.030.040.050.060.080.10 525-5740.01 0.020.030.040.050.060.070.09 575-6250.01 0.020.03 0.040.050.070.08 A duct has a SDP of 0.3 in. water column and a TEL of 46 ft. Find the friction loss using The table below:

18 Equivalent Length of Duct (ft) TOTAL PRESSURE DROP IN DUCT (In. of water column) 0.050.070.100.150.200.250.300.400.50 35-440.130.180.250.380.500.630.751.001.25 45-540.100.140.200.300.400.500.600.801.00 55-640.080.120.170.250.330.420.500.670.83 65-740.070.100.140.210.290.360.430.570.72 75-840.060.090.130.190.250.310.380.500.63 85-940.060.080.110.170.220.280.330.450.56 95-1040.050.070.100.150.200.250.300.400.50 105-1140.050.060.090.140.180.230.280.370.46 115-1290.040.060.080.120.170.210.250.330.42 130-1490.040.050.070.110.140.180.210.290.36 150-1690.030.040.060.090.130.160.190.250.31 170-1890.030.040.060.080.110.140.170.220.28 190-2140.030.040.050.080.100.130.150.200.25 215-2390.020.030.050.070.090.110.130.180.22 240-2640.020.030.040.060.080.100.120.160.20 265-2890.020.030.040.050.070.090.110.150.18 290-3240.020.03 0.050.070.080.100.130.17 325-3740.02 0.030.040.060.070.090.110.14 375-4240.010.020.030.040.050.060.080.100.13 425-4740.010.020.03 0.050.060.070.090.11 475-5240.010.02 0.030.040.050.060.080.10 525-5740.01 0.020.030.040.050.060.070.09 575-6250.01 0.020.03 0.040.050.070.08 A duct has a SDP of 0.3 in. water column and a TEL of 46 ft. Find the friction loss using The table below:

19 Equivalent Length of Duct (ft) TOTAL PRESSURE DROP IN DUCT (In. of water column) 0.050.070.100.150.200.250.300.400.50 35-440.130.180.250.380.500.630.751.001.25 45-540.100.140.200.300.400.500.600.801.00 55-640.080.120.170.250.330.420.500.670.83 65-740.070.100.140.210.290.360.430.570.72 75-840.060.090.130.190.250.310.380.500.63 85-940.060.080.110.170.220.280.330.450.56 95-1040.050.070.100.150.200.250.300.400.50 105-1140.050.060.090.140.180.230.280.370.46 115-1290.040.060.080.120.170.210.250.330.42 130-1490.040.050.070.110.140.180.210.290.36 150-1690.030.040.060.090.130.160.190.250.31 170-1890.030.040.060.080.110.140.170.220.28 190-2140.030.040.050.080.100.130.150.200.25 215-2390.020.030.050.070.090.110.130.180.22 240-2640.020.030.040.060.080.100.120.160.20 265-2890.020.030.040.050.070.090.110.150.18 290-3240.020.03 0.050.070.080.100.130.17 325-3740.02 0.030.040.060.070.090.110.14 375-4240.010.020.030.040.050.060.080.100.13 425-4740.010.020.03 0.050.060.070.090.11 475-5240.010.02 0.030.040.050.060.080.10 525-5740.01 0.020.030.040.050.060.070.09 575-6250.01 0.020.03 0.040.050.070.08 A duct has a SDP of 0.3 in. water column and a TEL of 46 ft. Find the friction loss using The table below: Thus, the duct size will be smaller

20 Equivalent Length of Duct (ft) TOTAL PRESSURE DROP IN DUCT (In. of water column) 0.050.070.100.150.200.250.300.400.50 35-440.130.180.250.380.500.630.751.001.25 45-540.100.140.200.300.400.500.600.801.00 55-640.080.120.170.250.330.420.500.670.83 65-740.070.100.140.210.290.360.430.570.72 75-840.060.090.130.190.250.310.380.500.63 85-940.060.080.110.170.220.280.330.450.56 95-1040.050.070.100.150.200.250.300.400.50 105-1140.050.060.090.140.180.230.280.370.46 115-1290.040.060.080.120.170.210.250.330.42 130-1490.040.050.070.110.140.180.210.290.36 150-1690.030.040.060.090.130.160.190.250.31 170-1890.030.040.060.080.110.140.170.220.28 190-2140.030.040.050.080.100.130.150.200.25 215-2390.020.030.050.070.090.110.130.180.22 240-2640.020.030.040.060.080.100.120.160.20 265-2890.020.030.040.050.070.090.110.150.18 290-3240.020.03 0.050.070.080.100.130.17 325-3740.02 0.030.040.060.070.090.110.14 375-4240.010.020.030.040.050.060.080.100.13 425-4740.010.020.03 0.050.060.070.090.11 475-5240.010.02 0.030.040.050.060.080.10 525-5740.01 0.020.030.040.050.060.070.09 575-6250.01 0.020.03 0.040.050.070.08 A duct has a SDP of 0.3 in. water column and a TEL of 46 ft. Find the friction loss using The table below:

21 In conclusion: The air friction chart is a valuable tool a designer can use to make sure the proper amount of airflow can be delivered through a duct system when the airflow is balanced.

Download ppt "Lesson 1 Friction Chart Primer 1.3 Friction Chart."

Similar presentations

Chapter V Frictionless Duct Flow with Heat Transfer Heat addition or removal has an interesting effect on a compress- ible flow. Here we confine the analysis.

Chapter V Frictionless Duct Flow with Heat Transfer Heat addition or removal has an interesting effect on a compress- ible flow. Here we confine the analysis.
Performance measurement

Performance measurement
Heating Systems Forced Air Systems.

Heating Systems Forced Air Systems.
SUPPLY DUCT SYSTEMS (Additional information. Read sections 18.4, 18.5, & 18.6) General –The supply duct system conveys conditioned air from an AHU to the.

SUPPLY DUCT SYSTEMS (Additional information. Read sections 18.4, 18.5, & 18.6) General –The supply duct system conveys conditioned air from an AHU to the.
CENTURY 21 ACCOUNTING © 2009 South-Western, Cengage Learning Accounting Concepts Page 152: two new Accounting Concepts: Business Entity – keep business.

CENTURY 21 ACCOUNTING © 2009 South-Western, Cengage Learning Accounting Concepts Page 152: two new Accounting Concepts: Business Entity – keep business.
Cycle Stop Valves 1” through 16” 1 GPM to 10,000 GPM.

Cycle Stop Valves 1” through 16” 1 GPM to 10,000 GPM.
Heating and Air Conditioning I

Heating and Air Conditioning I
Nonmetallic ducts (Additional information) –Fiberglass (also see section 18.5) Made of glass wool insulating material in which the stranded fiber wool.

Nonmetallic ducts (Additional information) –Fiberglass (also see section 18.5) Made of glass wool insulating material in which the stranded fiber wool.
AIR FLOW IN DUCTS Shaharin Anwar Sulaiman

AIR FLOW IN DUCTS Shaharin Anwar Sulaiman
Airflow Properties & Measurement

Airflow Properties & Measurement
ARCH-4372/6372 HVAC Distribution & Sizing HVAC Distribution Systems

ARCH-4372/6372 HVAC Distribution & Sizing HVAC Distribution Systems
1/128 Method Of Calibration Calibrating Hand Sprayers And High Pressure Hand Guns Because a gallon = 128 ounces and the area to be sprayed is 1/128 of.

1/128 Method Of Calibration Calibrating Hand Sprayers And High Pressure Hand Guns Because a gallon = 128 ounces and the area to be sprayed is 1/128 of.
Basic Hydraulics Irrigation.

Basic Hydraulics Irrigation.
2006 Oct. 19 DES Project -- Vaidas Simaitis, University of Illinois1 DHE – Detector Head Electronics Monsoon 80mm Crate Heat Load.

2006 Oct. 19 DES Project -- Vaidas Simaitis, University of Illinois1 DHE – Detector Head Electronics Monsoon 80mm Crate Heat Load.
Insect Control Field Days Sponsored by the Kansas Fruit Growers Association.

Insect Control Field Days Sponsored by the Kansas Fruit Growers Association.
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display. Chapter 20 Air Compressors and Pumps.

Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display. Chapter 20 Air Compressors and Pumps.
Chapter 3 Study guide.

Chapter 3 Study guide.
Water piping design.

Water piping design.
TEC 4607 Wind and Hydro Power Technologies Fall 2011.

TEC 4607 Wind and Hydro Power Technologies Fall 2011.
TEC 4607 Wind and Hydro Power Technologies Fall 2011.

TEC 4607 Wind and Hydro Power Technologies Fall 2011.

Similar presentations

Ads by Google