1. X-rays are generated from the interaction of accelerated e-’s & a target metal (tungsten).
Patient is placed between X-ray tube and silver halide film.
X-rays passed through the body are absorbed in direct proportion to tissue density.

2. X-rays penetrating the body strike the silver halide film and turn it dark, the more x-rays that penetrate, the darker the area inscribed on the film.
Bones & metal absorb or reflect X-rays are inscribed area on film is “lighter” or “more white”.
Soft tissues allow more X-rays to penetrate are inscribed area on film is “darker”.

3. Visualizing tissues of similar density can be enhanced using “contrast agents”.
Contrast agents: dense fluids containing elements of high atomic number (barium, iodine).
Contrast agents absorbs more photons than the surrounding tissue or cavity appears lighter.

4. These contrast agents can be injected, swallowed, or given by enema.

5. Diagnostic Medical X-Ray Unit

6. Tube Components X-ray tube is one of the components of a
basic radiographic unit.
Other components are:
Operating Console
X-ray tube
Automatic exposure
control
Exposure control
Beam limiting device

7. X-ray tube comprise of
3 components:
Cathode structure
Anode structure
Glass envelope

8. Functions of X-Ray Tube
An x-ray tube converts its input of electrical energy into an output of X-ray energy.
In the case of low power equipment, an x-ray tube also acts as a rectifier.

9. Production of X-Rays Requires 3 main components: Electron source
Method of accelerating electron
Method of
stopping
(braking)
electron

10. X-Ray Tube

11. Types of X-Ray Tube 2 types of x-ray tube: Stationary Anode
Rotating Anode
X-Ray Tube

12. Stationary Anode X-ray Tube
Low electric power.
Relative simplicity of design and construction and therefore low cost.
Suitable for the production of X-rays at low or medium intensities.
Used for applications such as dental radiography and mobile work where no sophisticated procedures such as rapid sequential imaging are required.

13. Rotating Anode X-ray Tube
Higher X-ray intensities and electrical power are provide by the anode tube since it has more efficient anode cooling.

14. Stationary anode tube: insert and housing

15. Construction of
Stationary Anode Tube

16. Glass envelope
Glass envelope is used to enclose the vacuum within the x-ray tube.
The envelope is joined to the copper anode at one end and the nickel cathode support at the other re-entrant seal.

17. The glass must be a good electrical insulator, or a substantial current will flow through it when a potential difference is applied between the anode and cathode.

18. Cathode Cathode consists of the following components: Filament
Focusing cup
Supporting wires
Cathode support

19. Filament(s)
The source of electron is a filament, heated by an electric current. The current increases the vibration of atoms within the filament so much that it emits heat and light.

20. The rate at which electrons are emitted rises with the filament’s temperature.
Thermionic emission: emission of electrons from the surface of a metal after heated

21. The filament is made of thin
coiled tungsten wire for the
following reasons:
Tungsten is a good thermionic emitter.
Tungsten has a low vapour pressure, i.e. it does not vaporise easily. It therefore lasts a long time.

22. Tungsten is rugged and able to be drawn into the thin wire required
Tungsten is rugged and able to be drawn into the thin wire required.(Easy to be shaped)

23. An x-ray tube may have 2 filaments of different sizes placed side-by-side. This is known as a dual-focus tube.

24. Electron Sources (e-) e- produced via thermionic emission
Electric current is supplied through the filament

25. Focusing cup
Focusing cups are usually made of either nickel, molybdenum or stainless steel. Cup shape metal Used to focus electrons towards target material. These materials possess high melting point and is a relatively poor thermionic emitter.

26. Anode
Anode is constructed of the 2 materials copper and tungsten, known as a compound anode.

27.  1% of energy is converted to X-rays, plus heat.
The anode rotates to increase
heat load
capacity.

28. e- accelerates to positively charged anode
Requires high potential difference to produce x-rays
Diagnostic energy range usually
30 kV – 150 kV

29. Target material
The target material is made of tungsten for the following reasons:
Tungsten has a high atomic number Z of 74. Intensity of an x-ray beam is proportional to Z.

30. Tungsten has a low vapour pressure, so that it does not readily vaporise at its normal working temperature.
Tungsten has a high melting point (3387°C), so that it can withstand the heat generated during an x-ray exposure without melting.

31. Tungsten has a relatively good thermal conductivity (½ that of Cu), thus enabling a rapid transfer of heat from the small focal area to the anode block by conduction.

32. Tungsten is a suitable material for machining into the shape and size required.
Focal spot: the area within the target material where electrons hit the target to produce x-ray.

33. (Anode Angle: the angle between the axis of X-ray beam and the target surface)

34. Advantages of using a line focus
Size of effective focus is smaller than the real focus (figure).
The filament
may thus be
relatively long
without giving
rise to poor
geometric unsharpness.

35. The area over which the heat is deposited is the area of the real focus.

36. Anode Heel Effect
Anode heel effect is due to the higher absorption of those X-rays which pass through the greater thickness of target.
This effect produced irregularities in the surface of the target as a result of prolonged use of the tube.

37. The formation of such irregularities in the target is known as pitting and is caused by vaporisation of the tungsten from the target (Figure).
Figure:
Effect of anode
grazing

38. The anode heel effect may have no practical significance, particularly if field size is small.

39. The use of rhenium tungsten alloy as a target material helps to minimize (pitting) crazing of the focal area and the use of high speed, large diameter, compound anodes permits increased loading of the focal area. (faster heat transfer).

40. Crazing is reduced by using a rhenium tungsten alloy (10% rhenium, 90% tungsten) as the target material. Radiation output is therefore maintained at a higher level giving the X-ray tube a longer useful life.