1. CRKIT R5 Clock Architecture WINLAB – Rutgers University June 13, 2013 Khanh Le

2. Zedboard Zynq System Clock Overview PSPL 33.333MHz ref clock (IC18, PS_CLK) F7 4 programmable PL clocks 100MHz ref clock (IC17, GCLK) Y9 For portability, use the 100MHz reference clock for PL section (will require one PLL) ref_clk_out (RF ref clock ~30MHz) B19, B20 L18, L19 dac_clk_in (dac ref clock) dac_clk_out (dac source synchronous clock) E19, E20 D18, C19 adc_clk_in (adc source synchronous clock)

3. Zynq PS System Clocks ARM PLL 33.333MHz PS_CLK I/O PLL DDR PLL Mux 6-bit prog. divider 6-bit prog. divider 6-bit prog. divider Mux Clock Ratio Generator cpu_6x4x cpu_3x2x cpu_2x cpu_1x CPU, SCU OCM AXI Interconnect ddr_3x ddr_2x Sync Async 6-bit prog. divider I/O Peripherals USB, Ethernet SDIO, SMC SPI, QSPI, UART CAN, I2C PL PL Clocks Check the clocks on EDK tool !! (REVISIT)

4. RF Interface dac_data_out[15:0] dac_clk_out dac_frame_out (unused) Not used for word-level, only for Byte- or Nibble-level AD9122 DAC AD9548 Clock Sync AD9523 Clock Gen AD9643 ADC dac_clk_in ref_clk_out(~30MHz) Jitter clean up adc_data_in[13:0] adc_clk_in adc_or_in I Q 1 0 LVDS CMT PLL ODDR (SAME_EDGE Mode) clock feedback DAC Interface RF Reference Clock ADC Interface I2C Interface @tx_clk ? CMT MMCM CTL REG Programmable ref. clock (ug472) 100MHz Rx Baseband D1 D2 Q D1 D2 Q By default, +Rising edge = I +Falling edge = Q +Twos complement Anti-aliasing filter cut-off @125MHz -> Nyquist sampling rate @250MHz I Q Q1 Q2 D IDDR (SAME_EDGE_PIPELINED Mode) CMT MMCM @125MHz clock feedback scl sdata I2C -> SPI PCORE INT REG @125MHz decimation (LP filtering) Clock domain crossing. Must support fractional synchronization e.g. 125MHz -> 20MHz Tx Baseband Interpolation ? By default, +Rising edge = I +Falling edge = Q +Twos complement + ~1ns skew between data and DCO (DCO delay vs data) @prog_rx_clk For fractional clock divider CLKOUT1 CLKOUT0 @100MHz sys_clk M=3, D=2, O1=5 M=3, D=2, O0=1.5 CLKOUT1 CLKOUT0

5. ODDR Timing

6. IDDR Timing

7. DAC Timing DAC Register Map Default Data bus sampling point is nominally 350ps after each edge of DCI signal, with uncertainty of +/- 300 ps. Data interface timing can be verified using the Sample Error Detection (SED) circuitry (reg 0x07, 0x67-0x73). Reference : AD9122_DAC.pdf

8. ADC Timing ADC Register Map Interleaved IQ channels : Chan A = I Chan B = Q Reference : AD9643_ADC.pdf ~1ns skew between data and DCO For parallel interleaved mode

9. Xilinx 7-series Clock Management Tile (CMT) Mixed-mode clock manager Phased-lock loop, subset of MMCM functions 1 CMT = 1 MMCM + 1 PLL Zynq Z-7020 PL clock resources : + 4 CMTs e.g. 4 MMCMs & 4 PLLs + 4 programmable clocks from PS CLKIN only Applications : + clock network deskew + frequency synthesis + jitter reduction

10. CMT - MMCM Programming port (ug472 + xapp888) Integer counter Independent clock control Fractional counter With Fclkin = 100MHz, M=1, D=1 : Integer divide : O0 = 1 : Fout = 100MHz O1 = 2 : Fout = 50MHz O2 = 3 : Fout = 33.33MHz O3 = 4 : Fout = 25MHz O4 = 5 : Fout = 20MHz O5 = 6 : Fout = 16.66MHz Fout = 80MHz, then O0 = Fclkin/Fout = 100/80 = 10/8 = 1.25 (fractional divide). Fout = 30MHz, O0 = 100/30 = 3.3333… Alternative, M=3, D=2, O1=5 : CLKOUT1 = 30MHz (rf ref clock) M=3, D=2, O0=1.5 : CLKOUT0 = 100MHz (system clock) With Fclkin = 125MHz (ADC sync clock), M=1, D=1 : Fout = 80MHz, O0 = 125/80 = 1.5625 Fout = 20MHz, O0 = 125/20 = 6.25 Attributes : M = CLKFBOUT_MULT_F D = DIVCLK_DIVIDE O = CLKOUT_DIVIDE (ug472, page 79)

11. CMT - PLL Integer only counter Programming port Attributes : M = CLKFBOUT_MULT_F D = DIVCLK_DIVIDE O = CLKOUT_DIVIDE

12. CMT - PLL Integer only counter Programming port Attributes : M = CLKFBOUT_MULT_F D = DIVCLK_DIVIDE O = CLKOUT_DIVIDE

13. MMCM and PLL Use Models (ug472, page 87) Requires two BUFGs Requires only one BUFG + jitter filtering + frequency synthesis + no phase requirement between Fin and Fout Off-chip compensation Input buffers must be in same bank. Use COREGEN to get additional settings information. Restrictions : F FB F in

14. Clock Distribution e.g. Zedboard Zynq how many APP can be supported ?

15. Decimation – Fractional Synchronizer

16. Interpolation ??

17. Clock Domain Abstraction Layers MOVE TO SEPARATE DESIGN DOCUMENT !