1. Learning Objectives
Define the following: Dimension line, Extension line, Reference dimension, and Leader
Be able to understand the basic rules of dimensioning
Apply dimensions to objects in accordance with engineering standards 2

2. Learning Objectives
The American National Standards Institute (ANSI) and the American Society of Mechanical Engineers (ASME) work hand in hand to set the standards in technical drawing. 2

3. Dimension Terminology:

4. Extension line
Thin sharp lines that extend from the edge of the drawing.
They mark the point from which a dimension begins.
They show the exact distance of the dimension.
They are drawn right angle with the dimension line.
They do not cross arrowheads.

5. Extension lines
Extension lines should be offset from the part by 1-2mm and should extend one 3-4mm beyond the dimension line

6. Dimension Line Thin , dark line terminated by an arrow.
It indicates the direction and extent of a dimension.

7. Dimension Spacing
The first row of dimensions should at least 10mm away from the part. Any dimensions beyond it must be a minimum of 6mm.

8. Arrowheads: Should be 3 times longer than the wide.

9. Dimensioning Rules
Avoid placing any dimensions on the part (inside the view) unless there is no other option.
Avoid dimensioning to hidden features
Always place the dimension where the characteristic shape is shown in the most descriptive view.
Always dimension holes in their circular view by stating the diameter of drilled holes. Specify the hole depth of special features such as countersinking with a note following the dimension.
Dimension rounded corners and arc features as radii where they appear in their rounded views.
If the same value is repeated many times, then use a general note for the features.
Always place the first row of dimensions a minimum distance of 10mm away from the edge of the part. Additional stacks can be a minimum 6mm away from each other.
Keep dimensions between the views whenever possible
Extension lines may cross each other and over other lines on the part, but dimension lines should never be crossed.
The overall dimension should always be given. It should be placed outside of smaller dimensions and be the furtherest dimension from the part. 16

10. Dimensioning Rules
Do not duplicate dimensions and avoid using unnecessary or superfluous dimensions
When all of the dimensions are expressed in inches, do not use inch mark (“) or the abbreviation for inches (in.)
For drawings dimensioned in inches, values less that one inch should not be preceded with a zero.
For metric drawings, omit the use of the millimeter (mm) notation following the numeral, as millimeters are the default units.
Conserve space and time by using abbreviations and standardized symbols whenever possible.
Reference dimensions should be placed in parentheses or should include the abbreviation “REF”.
Basic sizes (to be toleranced) should be placed inside a rectangular box
Extend leaders from the first of last word in a note. Point them toward the center of circular features that they are specifying.
Place dimensions among the various views to avoid crowding. Stagger horizontal dimensions to avoid contact or crowding of values. 16

11. 1. Avoid placing dimensions on the part (inside of the view).
See Essentials of Engineering Design Graphics Chapter 4

12. 2. Avoid dimensioning to hidden features
There is one exception:…… When the hidden line is a finished (√) surface
See Essentials of Engineering Design Graphics Chapter 4

13. 3. Always place dimensions where the characteristic shape is shown in the most descriptive view
See Essentials of Engineering Design Graphics Chapter 4

14. 4. Always dimension holes in their circular view with the Ø
4. Always dimension holes in their circular view with the Ø. Specify special features (hole types) with a note.
Also: Remember to locate hole position with ordinate dimensions to hole centers
See Essentials of Engineering Design Graphics Chapter 4

15. 5. Dimension rounded corners and arc features as radii where they appear in their rounded view.
See Essentials of Engineering Design Graphics Chapter 4

16. 6. If the same value is repeated many times, then use a general note for the feature. (ALL FILLETS AND ROUNDS ARE .125R)

17. 8. Place the first row of dimensions 10 mm away from the edge of the part.
Additional stacks of dimensions can be a minimum of 6mm away from each other

18. 9. Keep dimensions between views whenever possible .

19. 10. Extension lines may cross each other and over other lines on the part, but dimension lines should never be crossed. (Hint no “arrow-headed” lines can cross “arrow-headed” lines)

20. 11. The overall dimension should always be given
11. The overall dimension should always be given. It should be placed outside of smaller dimensions and be the farthest from the part.

21. 12. Do not duplicate dimensions and avoid using unnecessary or superfluous dimensions

22. 13. When all of the dimensions are expressed as inches
13. When all of the dimensions are expressed as inches. DO NOT use inch marks ('') or the abbreviation (.in)

23. 14. For drawings dimensioned in inches, values less than 1 inch should not be proceeded with a zero.

24. 15. For metric dimensions less than 1 mm DO place a zero in front of the decimal point.

25. 16. For metric drawings, omit the use of the millimeter (mm) notation following the numeral, as millimeters are the default units.

26. 17. The origin for baseline or ordinate dimensions used as a datum should be extended from a finished edge  of the part.

27. 19. Reference dimensions should be placed in parenthesis or should include the abbreviation “REF”. Basic sizes (to be toleranced) should be placed inside of a rectangular box

28. 20. Extend leaders from the first or last word in a note
20. Extend leaders from the first or last word in a note. Point them toward (but not touch) the center of the circular features that they are specifying.

29. 21. Place dimensions among the various views to avoid crowding
21. Place dimensions among the various views to avoid crowding. Stagger horizontal dimensions to avoid contact or crowding of the values

30. Angular features: Dimension angular features with either:
X,Y coordinate location or Vertex location & degrees

31. Dimension Styles
Aligned dimensions align with individual dimension lines.
Unidirectional dimensions text are written in horizontal direction.

32. A short review on Dimension “elements”
What is…
an Extension line?
an Extension line gap?
an Extension line extension?
a Dimension line?
a Dimension text?
a leader ?
What size…
Is an Arrowhead ?

33. Linear Dimensions
Linear dimensions are use to show basic dimensions of parts
They can be orientated either in a horizontal or vertical (or even aligned) fashion.

34. Dimensioning Errors:
What is wrong with:

35. Dimensioning Errors:
What is wrong with:

36. Dimensioning Errors:
What is wrong with:

37. Dimensioning Errors:
What is wrong with:

38. Quiz. Identify the parts, standards and errors shown in the given figure.

39. Key to Correction