1. Network Devices Repeaters, hubs, bridges, switches, routers, NIC’s

2. Devices and the layers at which they operate LayerName of LayerDevice 3NetworkRouters, layer 3 switches 2Data LinkSwitches, bridges, NIC’s 1PhysicalHubs

3. NIC’s (Network Interface Cards)Network Interface Cards This NIC has interfaces for twisted pair, thicknet, and thinnet connectors.

4. Repeaters Signal attenuation or signal loss – signal degrades over distance Repeaters clean, amplify, and resend signals that are weakened by long cable length. Built-in to hubs or switches

5. Hubs OSI layer 1 hardware OSI layer 1 Hubs regenerate and retime network signals Hubs propagate signals through the network They cannot filter network traffic They cannot determine best path They are used as network concentration points They are really multi-port repeaters Uplink port – crossover mode or straight through mode

6. Hub

7. Bridges A layer 2 device designed to create two or more LAN segments, each of which is a separate collision domain. The purpose is to filter traffic on a LAN, to keep local traffic local, yet allow connectivity to other segments of the network. Filter traffic by looking at the MAC address Frame filtering

8. Bridge

9. Bridges If the frame is addressed to a MAC address on the local side of the bridge, it is not forwarded to the other segment MAC addresses on the other segment are forwarded Bridges maintain a MAC address table for both segments they are connected to

10. Cycle of bridges Bridged network can span many segments Broadcasts are sent to all segments

11. Bridges Distributed Spanning Tree Distributed Spanning Tree If all bridges forward broadcasts, infinite loops can occur Bridges perform DST on boot to determine which bridges will not forward broadcasts

12. Switched networks Shared ethernet networks perform best when kept to 30-40 percent full capacity This is a result of CSMA/CD A LAN switch is a high-speed multiport bridge which segments each port into its own collision domain and can access the full bandwidth collision domain

13. Switch

14. Devices and the layers at which they operate LayerName of LayerDevice 3NetworkRouters, layer 3 switches 2Data LinkSwitches, bridges, NIC’s 1PhysicalHubs

15. Switches Each port is a simulated segment to itself

16. Store and Forward Switches Do error checking on each frame after the entire frame has arrived into the switch If the error checking algorithm determines there is no error, the switch looks in its MAC address table for the port to which to forward the destination device Highly reliable because doesn’t forward bad frames Slower than other types of switches because it holds on to each frame until it is completely received to check for errors before forwarding

17. Cut Through Switch Faster than store and forward because doesn’t perform error checking on frames Reads address information for each frame as the frames enter the switch After looking up the port of the destination device, frame is forwarded Forwards bad frames Performance penalty because bad frames can’t be used and replacement frames must be sent which creates additional traffic

18. Fragment free cut through switch Combines speed of cut through switch with error checking functionality Forwards all frames initially, but determines that if a particular port is receiving too many bad frames, it reconfigures the port to store and forward mode Preferred switching solution

19. Unmanaged/Intelligent switches Unmanaged – provides LAN’s with all the benefits of switching Fine in small networks Intelligent switches tracks and reports LAN performance statistics Have a database ASIC (application specific integrated circuit) on board to collect and store data which you view through a software interface

20. Layer 3 switch By definition a switch filters or forwards frames based on MAC addresses. This makes a switch a layer 2 device. Now we have layer 3 switches which have routing capability. If a data frame can’t be switched it is routed. Each port is a separate LAN port, but the forwarding engine actually calculates and stores routes based on IP addresses, not MAC addresses Usually support only IP or IP and IPX

21. Physical Layer Physical Layer Broadcast Physical layer broadcasts – implemented by non-switched Ethernet networks through shared cabling and hubs Each bit that is transmitted is physically received by every station Switches and VLAN’s don’t do physical layer broadcasts

22. MAC-level broadcast MAC-level broadcast – deal with how to handle MAC level broadcast frames; that is the data frames that have a broadcast destination MAC address MAC-level broadcast frames are addressed to all MAC addresses on a given network (not a network segment, but an actual network as defined by its network address) A regular switch forwards all broadcast frames out all ports, but a VLAN switch forwards broadcast frames only to ports that are part of the same VLAN Multiple switches can be part of the same VLAN

23. VLAN Switches None of the VLAN’s can communicate unless each VLAN is connected to a router or layer 3 switch Each VLAN is separating collision traffic associated with MAC Addresses (layer 2) and each VLAN is separating the network-to- network broadcast traffic. In other words each VLAN is acting as a separate network so a layer 3 device is necessary for them to communicate

24. Router

25. A router is a networking device that forwards data packets between computer networks. Routers perform the "traffic directing" functions on the Internet. A data packet is typically forwarded from one router to another through the networks that constitute the internetwork until it reaches its destination node.

26. Router

28. Lets Make a Network