1. Validator TM and Validator-NT TM Product Training

2. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION2 What does the Validator do?  Performs basic to advanced tests on network, telco, and coax cabling –Wiremap: opens, shorts, split pairs, miswires, reversals –Distance to opens and shorts  Speed Certifies Ethernet cabling up to Gigabit speeds –Bit Error Rate Test –Delay Skew –Signal to Noise Ratio  Allows for planning and documenting the job with included Plan-Um software –Network layout –Test schedule –Test results

3. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION3 What does the Validator-NT do?  Everything that the Validator does PLUS active network tests: –Port discovery up to gigabit Ethernet –IP Ping –Cisco Discovery Protocol

4. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION4 Cabling Tests  Wiremap  Distance to opens and shorts

5. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION5 Ethernet Speed Certification  Skew, SNR, BERT

6. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION6 Planning and Documenting the Job

7. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION7 Active Network Tests  Port Discovery  Cisco Discovery Protocol (Not Shown)  Ping

8. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION8 Hub Flash

9. Using the Validator

10. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION10 Some Basic Information – Cable Types  Common cable types and their pass/fail criteria are pre-defined and cannot be edited  Custom cable types can be created

11. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION11 Steps to a Successful Job 1.Plan the Job 2.Perform Tests 3.Document

12. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION12 Plan the Job  Use Plan-Um to plan the job –Job Information –Cable Test Schedule  Load the job onto the Validator

13. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION13 Job Information

14. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION14 Cable Test Schedule

15. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION15 Load the Cable Test Schedule onto the Validator  Connect the Validator to a free USB port on your PC  OR remove the CF card from the Validator and insert it into a card reader on your PC  NOTE: Validator must be turned off when card is removed or when USB cable is connected  The CF card will appear as a drive on the PC  Copy the job file to the CF card or simply “save as” and navigate to the CF card to save the file directly to the CF card from Plan-Um

16. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION16 Perform Tests  Power on the Validator and Launch Auto Test (use arrow keys to highlight and then press SEL)  Select Job Utilities and then select Open to open the job file  Use the arrow keys to highlight the job file you wish to load and then press the F1 key (Open)  The job file will be loaded and you will be returned to the main screen with Auto Test highlighted  Press SEL  Cable Test Schedule will be highlighted  Press SEL to launch

17. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION17 Cable List  The Cable List will be shown  Highlight the cable to be tested using the up and down arrows  Connect the remote to the far end of the cable to be tested  Connect the main unit to the local end of the cable to be tested  Press the Test button

18. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION18 Test Results  Once the auto tests have completed, the Validator will show a Pass or Fail result  Continue through the Cable List until all cables have been tested

19. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION19 Document  Transfer job file back to PC and open with Plan-Um  Print individual results or full report

20. Advanced and Active Network Tests

21. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION21 Hub Flash  Hub Flash sends an intermittent link signal to flash the link status light on Ethernet equipment.

22. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION22 Port Discovery  Identifies telephone or network devices connected to the other end of the jack or cable. Validator-NT reports on existing services or Ethernet link with advertised speed.

23. © 2008 JDSU. All rights reserved.JDSU CONFIDENTIAL & PROPRIETARY INFORMATION23 Ping  Verifies connectivity to resources on or off the network and the IP addresses.  Validator-NT can simultaneously Ping up to seven different IP addresses and can be run in DHCP or static modes.