2. ReeFi-LED WiFi Setup Overview 2 Ways to Connect ReeFi-LED to your home WiFi SmartWiFi Mode from mobile app WiFi AP Mode from web browser

3. ReeFi-LED WiFi Setup Overview When ReeFi-LED first power up, it will try to reconnect to last known WiFi (ssid and password). If it can not, it will blink in blue to indicate it’s entering into SmartWiFi. After about 5 mins if WiFi still is not establish, it will enter WiFi AP Mode. This is indicated by solid Blue LEDs with blinking Red/Cyan LEDs. If WiFi is not established in next 15min, it will restart and the whole process starts again. This is to prevent ReeFi- LED to be stuck in WiFi Setup modes after power outage. After power outage, most new WiFi Routers are very complex and takes a long time to completely operational.

4. ReeFi-LED WiFi Setup – SmartWiFi Mode Step 1 Launch Android ReeFi-LED app. Touch the upper right dots then WiFi SmartStart.

5. ReeFi-LED WiFi Setup – SmartWiFi Mode Step 2 Make sure your ReeFi-LED is in SmartWiFi with blinking Blue LEDs. When you device is connected to your home WiFi network, SSID field will automatically show your WiFi. Enter your WiFi Password and select how many ReeFi-LEDs are to connect. Then press Confirm. When correct password is enter, ReeFi-LED will stop blinking.

6. Assign ReeFi-LED to Aquarium Touch Upper left for Menu. Select Setup at the bottom Select SCAN to search for new ReeFi-LED. Assign it to an Aquarium. Then select SAVE. Touching the ReeFi-LED- xxxxx will cause it to blink twice.

7. ReeFi-LED WiFi Setup – WiFi AP Mode Step 1 Power ReeFi-LED and wait till it enters WiFi AP Mode. After about 5 mins, SmartWiFi will timeout and ReeFi-LED will switch to WiFi AP Mode. This is indicated by solid Blue LEDs and blinking Red/Cyan LEDs. New WiFi will be available called: ReeFi-LED-xxxxx Connect to this new WiFi from your PC/mobile device.

8. Step 2 Once connected to: ReeFi-LED-xxxxx Open your web browser (Chrome, IE, Safari) and enter IP address in the URL: 192.168.5.1 Enter your WiFi name (SSID) and password, then click save. Browser will auto refresh page a several time. If SSID and password are enter correct, it will refresh with your ReeFi- LED IP address. Click on Reboot to restart your ReeFi- LED.

9. WiFi Router DHCP Example ReeFi-LED IP address can be found from previous WiFi setup. However, most home WiFi routers will randomly re- assign IP address weekly. To determine your ReeFi-LED new IP address, you can login to your WiFi Router and look at the clients list (refer to your WiFi Router’s manual). It’s recommended that from your WiFi Router DHCP setting to set the ReeFi-LED ip to static.

10. Program your ReeFi-LED Connect to your WiFi network Open your web browser (Chrome, IE, Safari) and enter your ReeFi IP address in the URL: 192.168.1.152/settings.html

11. Basic Settings Info LED power level is from 0 to 1023. At 0, LED driver circuit is completely power off. Minimum power level to visually power LED is 2. To allow 1024 level is power setting, at very low power (less than 20), you might notice random power flex. This is due LEDs are switch on and off very quickly but mostly off. Only when Submit is click are setting saved to ReeFi- LED. Refresh button will show you current settings.

12. 5 Modes Sunrise Midday Sunset Night Moon Current is the present time status. Hr and Min set the start time of each mode. Delay X set the rate of LED ramp up and ramp down.

13. Sunrise Mode is unique in that highest LED channel will ramp up first, then follow by next highest LED channel. In this example, Blue1 will ramp up to 50 first. Then Blue1 and Red/Cyan will ramp up together to 100 and 50, respectively. Then Blue1, Red/Cyan, and Blue2 will ramp up to 200, 150, 100, respectively before White/Blue starts ramping up and etc.

14. Midday Mode Cloud Max% is the max cloud coverage. Cloud coverage is random from 0-Max% every 20min during Midday. Cloud Factor (CF) can override cloud per channel by multipling CF to current cloud coverage. 0 means no cloud coverage. Peak Override: This override Midday settings by % of Midday power between Hrs after Midday start and Hrs before Sunset start.

15. Moon Mode Moon settings determine the brightest moon light when moon phase is 100% (full moon). To prevent complete darkness when moon phase is near 0%, set Dimmest Moon override.