1. Sistem Telekomunikasi, Sukiswo, ST, MT Sukiswo sukiswok@yahoo.com
Pulse Code Modulation
Sukiswo
Sistem Telekomunikasi, Sukiswo, ST, MT

2. Sistem Telekomunikasi, Sukiswo, ST, MT
Outline
Pulse Code Modulation
Quantizing
Encoding
Analogue to Digital Conversion
Bandwidth of PCM Signals
Sistem Telekomunikasi, Sukiswo, ST, MT

3. Sistem Telekomunikasi, Sukiswo, ST, MT
PULSE CODE MODULATION
DEFINITION:
Pulse code modulation (PCM) is essentially analog-to-digital conversion of a special type where the information contained in the instantaneous samples of an analog signal is represented by digital words in a serial bit stream.
Sistem Telekomunikasi, Sukiswo, ST, MT

4. Sistem Telekomunikasi, Sukiswo, ST, MT
PULSE CODE MODULATION
The advantages of PCM are:
Relatively inexpensive digital circuitry may be used extensively.
PCM signals derived from all types of analog sources may be merged with data signals and transmitted over a common high-speed digital communication system.
In long-distance digital telephone systems requiring repeaters, a clean PCM waveform can be regenerated at the output of each repeater, where the input consists of a noisy PCM waveform.
The noise performance of a digital system can be superior to that of an analog system.
The probability of error for the system output can be reduced even further by the use of appropriate coding techniques.
Sistem Telekomunikasi, Sukiswo, ST, MT

5. Sistem Telekomunikasi, Sukiswo, ST, MT
PULSE CODE MODULATION
The PCM signal is generated by carrying out three basic operations:
Sampling
Quantizing
Encoding
Sistem Telekomunikasi, Sukiswo, ST, MT

6. Sistem Telekomunikasi, Sukiswo, ST, MT
PULSE CODE MODULATION
Sampling operation generates a flat-top PAM signal.
Quantizing operation approximates the analog values by using a finite number of levels. This operation is considered in 3 steps
Uniform Quantizer
Quantization Error
Quantized PAM signal output
PCM signal is obtained from the quantized PAM signal by encoding each quantized sample value into a digital word.
Sistem Telekomunikasi, Sukiswo, ST, MT

7. Analog to Digital Conversion
ADC
Sample
Quantize
Analog
Input
Signal
Encode
111
110
101
100
011
010
001
000
Digital Output
Sistem Telekomunikasi, Sukiswo, ST, MT

8. Analog to Digital Conversion
The Analog-to-digital Converter (ADC) performs three functions:
Sampling
Makes the signal discrete in time.
If the analog input has a bandwidth of W Hz, then the minimum sample frequency such that the signal can be reconstructed without distortion.
Quantization
Makes the signal discrete in amplitude.
Round off to one of q discrete levels.
Encode
Maps the quantized values to digital words that are  bits long.
If the (Nyquist) Sampling Theorem is satisfied, then only quantization introduces distortion to the system.
Sistem Telekomunikasi, Sukiswo, ST, MT

9. Sistem Telekomunikasi, Sukiswo, ST, MT
Quantization
The output of a sampler is still continuous in amplitude.
Each sample can take on any value e.g , 0.001, etc.
The number of possible values is infinite.
To transmit as a digital signal we must restrict the number of possible values.
Quantization is the process of “rounding off” a sample according to some rule.
E.g. suppose we must round to the nearest tenth, then:
> > 0
Sistem Telekomunikasi, Sukiswo, ST, MT

10. Illustration of the Quantization Error
Sistem Telekomunikasi, Sukiswo, ST, MT

11. Quantization Characteristic
Uniform Quantization
Most ADC’s use uniform quantizers.
The quantization levels of a uniform quantizer are equally spaced apart.
Uniform quantizers are optimal when the input distribution is uniform. When all values within the Dynamic Range of the quantizer are equally likely. 2 4 6 8 1 5 3
Output sample XQ -2 -4 -6 -8
Dynamic Range:
(-8, 8) 7 -7 -3 -5 -1
Quantization Characteristic
Input sample X
Example: Uniform  =3 bit quantizer
q=8 and XQ = {1,3,5,7}
Sistem Telekomunikasi, Sukiswo, ST, MT

12. Sistem Telekomunikasi, Sukiswo, ST, MT
Quantization Example
Analogue signal
Sampling TIMING
Quantization levels.
Quantized to 5-levels
Quantization levels
Quantized 10-levels
Sistem Telekomunikasi, Sukiswo, ST, MT

13. PCM encoding example Levels are encoded using this table M=8
Table: Quantization levels with belonging code words
Levels are encoded using this table
M=8
Chart 1. Quantization and digitalization of a signal.
Signal is quantized in 11 time points & 8 quantization segments.
Chart 2. Process of restoring a signal.
PCM encoded signal in binary form:
Total of 33 bits were used to encode a signal
Sistem Telekomunikasi, Sukiswo, ST, MT

14. Sistem Telekomunikasi, Sukiswo, ST, MT
Encoding
The output of the quantizer is one of M possible signal levels.
If we want to use a binary transmission system, then we need to map each quantized sample into an n bit binary word.
Sistem Telekomunikasi, Sukiswo, ST, MT

15. Sistem Telekomunikasi, Sukiswo, ST, MT
Encoding
Encoding is the process of representing each quantized sample by an  bit code word.
The mapping is one-to-one so there is no distortion introduced by encoding.
Some mappings are better than others.
A Gray code gives the best end-to-end performance.
The weakness of Gray codes is poor performance when the sign bit (MSB) is received in error.
Sistem Telekomunikasi, Sukiswo, ST, MT

16. Sistem Telekomunikasi, Sukiswo, ST, MT
Gray Codes
With gray codes adjacent samples differ only in one bit position.
Example (3 bit quantization):
XQ Natural coding Gray Coding
With this gray code, a single bit error will result in an amplitude error of only 2.
Unless the MSB is in error.
Sistem Telekomunikasi, Sukiswo, ST, MT

17. Waveforms in a PCM system for M=8
(a) Quantizer Input output characteristics
(b) Analog Signal, PAM Signal, Quantized PAM Signal
(c) Error Signal
(d) PCM Signal
Sistem Telekomunikasi, Sukiswo, ST, MT

18. PCM Transmission System
Sistem Telekomunikasi, Sukiswo, ST, MT

19. Practical PCM Circuits
Three popular techniques are used to implement the analog-to-digital converter (ADC) encoding operation:
The counting or ramp, ( Maxim ICL7126 ADC)
Serial or successive approximation, (AD 570)
Parallel or flash encoders. ( CA3318)
Sistem Telekomunikasi, Sukiswo, ST, MT

20. Practical PCM Circuits
The objective of these circuits is to generate the PCM word.
Parallel digital output obtained (from one of the above techniques) needs to be serialized before sending over a 2-wire channel
This is accomplished by parallel-to-serial converters [Serial Input-Output (SIO) chip]
UART,USRT and USART are examples for SIO’s
Sistem Telekomunikasi, Sukiswo, ST, MT

21. Bandwidth of PCM Signals
The spectrum of the PCM signal is not directly related to the spectrum of the input signal.
The bandwidth of (serial) binary PCM waveforms depends on the bit rate R and the waveform pulse shape used to represent the data.
The Bit Rate R is
R=nfs
Where n is the number of bits in the PCM word (M=2n) and fs is the sampling rate.
Sistem Telekomunikasi, Sukiswo, ST, MT

22. Bandwidth of PCM Signals
For no aliasing case (fs≥ 2B), the MINIMUM Bandwidth of PCM Bpcm(Min) is:
Bpcm(Min) = R/2 = nfs//2
The Minimum Bandwidth of nfs//2 is obtained only when sin(x)/x pulse is used to generate the PCM waveform.
For PCM waveform generated by rectangular pulses, the First-null Bandwidth is:
Bpcm = R = nfs
Sistem Telekomunikasi, Sukiswo, ST, MT