1. ENERGY METER TO INDICATE BILLING IN RUPEES FOR LOAD WISE OR DAY WISE
Project Title
ENERGY METER TO INDICATE BILLING IN RUPEES FOR LOAD WISE OR DAY WISE
Under the Guidance of
Submitted by

2. ABSTARCT
This project deals with the calculation of the energy meter billing based on the load consumption given as an input using set up buttons.
The microcontroller calculates the rupees that will be consumed by the loads as per the input given and displays it on the 16X2 LCD interfaced with the microcontroller.
This project is powered by an on-board power supply takes the ac power and converts it into dc power that is fed to on-board devices and integrated circuits.

3. PROJECT BLOCK DIAGRAM

4. HARDWARE COMPONENTS POWER SUPPLY BLOCK
MICROCONTROLLER (AT89S52/AT89C51)
ENERGY METER
OPTO COUPLER/OPTO ISOLATOR (MCT2E)
LCD
1N4007
RESISTOR
CAPACITOR

5. POWER SUPPLY Bridge rectifier 5v Regulator 230 V AC 50 Hz 5V DC
Filter(470µf)
12V step down
transformer

6. It is a smaller computer Has on-chip RAM, ROM, I/O ports...
MICROCONTROLLER
It is a smaller computer
Has on-chip RAM, ROM, I/O ports...
RAM
ROM
I/O Port
Timer
Serial COM Port
Microcontroller
CPU
A single chip

7. INTERNAL STRUCTURE OF A MICRO CONTROLLER-AT89S52/51
CPU
On-chip RAM
On-chip ROM for program code
4 I/O Ports
Timer 0
Serial Port
OSC
Interrupt Control
External interrupts
Timer 1
Timer/Counter
Bus Control
TxD RxD
P0 P1 P2 P3
Address/Data
Counter Inputs

8. Features of AT89S51/52 Compatible with MCS®-51 Products
8K Bytes of In-System Programmable (ISP) Flash Memory
Endurance: 10,000 Write/Erase Cycles
4.0V to 5.5V Operating Range
Fully Static Operation: 0 Hz to 33 MHz
256 x 8-bit Internal RAM
32 Programmable I/O Lines
Three 16-bit Timer/Counters
Eight Interrupt Sources
Full Duplex UART Serial Channel
Interrupt Recovery from Power-down Mode
Watchdog Timer
Dual Data Pointer

9. Pin Description

10. ENERGY METER
An energy or electric meter is a device that measures the amount of electrical energy consumed by a residence, business, or an electrically-powered device.
Electric meters are typically calibrated in billing units, the most common one being the kilowatt hour.
Periodic readings of electric meters establish billing cycles and energy used during a cycle.

11. Opto-isolator Opto coupler is a 6 pin IC.
It is a combination of 1 LED and a transistor.
when light falls on the Base-Emitter junction then it switches pin5 goes to zero.
When logic zero is given as input then the light doesn’t fall on transistor so it doesn’t conduct which gives logic zero as output.
When logic 1 is given as input then light falls on transistor so that it conducts, that makes transistor switched ON and it forms short circuit this makes the output is logic zero as collector of transistor is connected to ground.

12. LIQUID CRYSTAL DISPLAY (LCD)
Most common LCDs connected to the microcontrollers are 16x2 and 20x2 displays.
This means 16 characters per line by 2 lines and 20 characters per line by 2 lines, respectively.
The standard is referred to as HD44780U, which refers to the controller chip which receives data from an external source (and communicates directly with the LCD.

13. If an 8-bit data bus is used the LCD will require 11 data lines
LCD BACKGROUND
If an 8-bit data bus is used the LCD will require 11 data lines
(3 control lines plus the 8 lines for the data bus)
The three control lines are referred to as EN, RS, and RW
EN=Enable (used to tell the LCD that you are sending it data)
RS=Register Select (When RS is low (0), data is treated as a command)
(When RS is High(1), data being sent is text data )
R/W=Read/Write (When RW is low (0), the data written to the LCD)
(When RW is low (0), the data reading to the LCD)

14. Working of Project
The project uses a commercial digital energy meter and derives
positive pulses from the same by taking a connection from the pulsing
LED.
The pulsing LED pulses 3200 times for 1 unit of electrical energy i.e., 1
kilo watt hour.
Using push buttons the price for 1 unit and also the time is entered i.e.,
the time for which the load is to be used.
This data is taken and calculated by MC and it displays the rupees
which have to be paid for using the load for the prescribed time
entered.

15. Soft ware Requirements
Keil an ARM Company makes C compilers, macro assemblers, real-time kernels, debuggers, simulators, integrated environments, evaluation boards, and emulators for ARM7/ARM9/Cortex-M3, XC16x/C16x/ST10, 251, and 8051 MCU families.
Compilers are programs used to convert a High Level Language to object code. Desktop compilers produce an output object code for the underlying microprocessor, but not for other microprocessors.

16. i.e the programs written in one of the HLL like ‘C’ will compile the code to run on the system for a particular processor like x86 (underlying microprocessor in the computer).
For example compilers for Dos platform is different from the Compilers for Unix platform  So if one wants to define a compiler then compiler is a program that translates source code into object code.

17. THANKYOU