1. USING TOOLS TO BASED OPERATION
Sumariyanto: 2007
Based Competence:
Describing how to operate machine

2. Describing how to operate machine
AIM OF STUDY
Based Competence:
Describing how to operate machine
After finished learning this competence:
Student are able to describe how to operate the machine

3. THE PROCEDURE OF SETTING WORK PIECE TO SHAPING MACHINE
Hit the work piece
Adjust the parallel block tightly
Tighten to Chuck

4. PROCEDURE OF SETTING WORK PIECE TO SHARPING MACHINE
Parallel Block
The Proper Setting of Parallel Block

5. OPERATING SHARPING MACHINE
Parts of regulator of position and length step
Activator motor
Activator gear
Activator wheel.
Crank block
Arm Axis swing
Arm swing
Head slide
Chuck of head slide

6. THE LENGTH OF CUTTING
The length of cutting (L) are set to length of work piece (l), early length of work piece (la) and the rest one (lb)

7. DEPT FEED RATE
The number of feed rate is a depended to horizone of machine workmanship (harsh/smooth)

8. Arrange Thick Feed Rate
DEPT AND THICK FEED RATE
Arrange Dept Feed Rate
Arrange Thick Feed Rate

9. DRILLING MACHINE

10. OPERATING OF DRILLING MACHINE
Belt of Regulator of Rotation Speed

11. Fix aperture vocal point
by using centre punch
Placing Drilling Position

12. Depth Governor Handle is drilling
Speed and Depth of Cutting

13. LATHE

14. PROCEDURE OF SETTING WORK PIECE Chucking of short cylinder work piece
TO LATHE
Chucking of long cylinder work piece
Chucking of short cylinder work piece

15. PROCEDURE OF SETTING WORK PIECE
TO LATHE
Chucking of wide cylinder work piece
Using of circular central head

16. PROCEDURE OF SETTING WORK PIECE
TO LATHE
Chucking of rectangle work piece

17. LATHE OPERATION
Movements in Drilling Process

18. v = d (mm) x  x n (rpm) (m/men)
LATHE OPERATION
v = d (mm) x  x n (rpm)
v = d (mm) x  x n (rpm) (m/men)
1000
Kecepatan potong dinyatakan dalam m/menit, sedangkan ukuran benda dalam mm, maka :
Circular regulation and speed of work piece cutting

19. MOVEMENT OF LATHE CARRIAGE
Main spindle
Apron
Handle of apron
Cross slide
Handle cross slide
Top carriage

20. CUTTING DIRECTION
The fuction of cutting direction is to less diameter of work ing piece

21. CUTTING DIRECTION
The function of cutting direction is to sharp or cut the face /edge of working piece

22. CUTTING DIRECTION The function of cutting direction is to sharp
the edge of working piece

23. The cutting direction of this shaping to make couture on surface

24. Frais Machine

25. OPERATING FRAIS MACHINE
Movements in Milling
Bounding
Cutting
Running

26. Methode In Milling Millling by Oposite Direction One Way Milling
Neutral Milling

27. SETTING DIRECTION OF MOVEMENT MILLING
With turning around handle long table hence work piece will make a move towards length
Move Towards Length

28. SETTING DIRECTION OF MOVEMENT MILLING
Athwart impulse of work piece is done with turning around handle athwart table equiped with by scale nonius to know impulse scale.
Diagonal movement

29. SETTING DIRECTION OF MOVEMENT MILLING
Depth milling of work piece is arranged by the way of boosts up engine table and free work piece with cutter by the way of reducing it.
Vertical movement

30. BASIC MACHINE OPERATION

31. REFERENCE
Tim Fakultas Teknik Universitas Negeri Yogyakarta Penggunaan dan Pemeliharaan Alat Ukur. Yogyakarta: Direktorat Pendidikan Menengah Kejuruan, Depdiknas.
Sumariyanto Bubut Dasar. Malang: PPPPGT Malang
Widarto Teknik Pemesinan Jilid 1 (BSE). Jakarta: Dit. PSMK DEPDIKNAS