1. 2017 Single Module Beta to LP Changes
CEAF Type: Change Notification
Technical Configuration(s) Affected: D313029BX03, D563025BX03, D103016BX03
Engine Family Affected: B6.7, L9, X15
Market(s) Impacted: On-Highway EPA 2017
Anticipated Production Date: LP
Option(s) Affected: PE9487, PE9485, PE9488, PE9486, PE9532, PE9534, PE9533, PE9535, PE1072, PE1073, PE1074, PE1075
Confidential - Restricted

2. Impacted Configurations
Summary Table
Change
Impact on IQA Testing
Impact on Fit Check
Impacted Configurations
Horizontal DPF sensor table Bracket changes for wire routing
None Expected
Minimal to none
All
DPF sensor table EGTS Bolt hole location changes
Alignment Arrow
SI/SO heat shield change to reduce lift eye black out zone
SISO, SIEO, EISO
Added slot to outlet tube
3 piece heat shield design on side outlet
EISO, SISO
14-way Connector Location Change
Moderate to High
MR & HD: EISO, SIEO, SISO
HD EIEO
MR EIEO
Part Number Etching Relocation
Vertical: EIEO, EISO, SIEO
Heat Shield Mounting Bracket
All except SI configurations
LP models are being generated with these changes implemented.

3. Horizontal DPF sensor table Bracket changes for wire routing
Wires too tight at the zip tie
Addition of bend at the EGTS ears
Reason for Change: Reduce stress on EGTS wire from pulling it downwards
Configurations Affected: All

4. DPF sensor table EGTS Bolt hole location changes
Reason for Change: Increase space for tool clearance.
Configurations Affected: All

5. DPF sensor table EGTS Bolt hole location changes

6. Alignment Arrow
Adding an Alignment Arrow deboss between the DPF and the Compact Mixer
Reason for Change: Better alignment when servicing DPF
Configurations Impacted: All

7. SI/SO heat shield change
Reason for Change: Reduce lift eye blackout zone
Curve of Beta flange requires ±75o lift eye blackout zone
“Flatter” LP flange reduces blackout zone to ±35o
Configurations Impacted: SISO,
SIEO, EISO 0o 0o
35o
35o
75o
75o
Current Beta Design Lift Eye Capability for inlet/outlet
Proposed LP Design Lift Eye Capability for inlet/outlet

8. Add slot to outlet tube
Added slot to outlet tube as a “location feature” for ease of assembly.

9. 3 Piece Heat shield design on Side Outlets
Current Side Outlet Assembly steps
Side outlet 3 piece heat shield change for LP +
Visible new welds

10. 14-pin connector location change
The 14-pin connector location changed from beta to LP. The change is driven by the removal of a molded bracket under the connector, and by switching from overfoam to conduit.
Configurations impacted are horizontal:
MR & HD: EISO, SIEO, SISO: Slides 10 and 11
HD EIEO: Slides 10 and 11
MR EIEO: Slides 12 and 13

11. 14-pin connector location
OEM Connector
Overfoam Harness Design (Beta)
OEM Connector
LP (red) vs. Beta (yellow)
- MR and HD EISO, SIEO, and SISO
- HD EIEO

12. 14-pin Connector Beta to LP Comparison
55.7 mm
*LP model does not reflect actual routing. Revised models will not show interference.

13. 14-pin Connector Beta to LP Comparison
Red = Beta
Green = LP
MR EIEO

14. 14-pin Connector Beta to LP Comparison
Red = Beta
Green = LP
MR EIEO

15. Part Number Etching Relocation
Part Numbers and other markings have been relocated for ease of manufacturability on all configurations.
Refer to next two slides for more details on relocation changes.

16. Part Number Etching Relocation
Side Outlet
Full Overview for LP
CES DOC module bar code
CES DPF module bar code
CES CM module bar code
+ TLA bar code
CES SCR module
Part Number Etching Relocation
Beta Original Location (post-deviation)
End Outlet
Beta Original Location (post-deviation)
LP Location
Horizontals

17. Part Number Etching Relocation
Changed alignment of etching due to weld joint
BETA
Part Number Etching Relocation
1030mm
TLA#
Sub assembly PN
Verticals LP

18. Heat Shield Mounting Bracket
The heat shield mounting bracket feature will no longer be offered on side outlet.
The heat shield mounting bracket (circled) will be a selectable feature for side inlets only.
The capability of selecting heat shield mounting brackets on side outlets has been removed on the latest input sheet revision
BETA/Side Inlet LP LP