2. System Important Points for Wiring
Device1
Device2
Device3
DeviceN 1 2 3 4
" Hand-in-Hand" Connection
Device1
Device3
Device2 1 2 3 4
" Star "Connection
It is not good for using the " Star "Connection way.
We suggest you to connect the products hand in hand, one by one.

3. System Important Points for Wiring
Programming
Module
Power Supply
Dimming Module
Relay Module
Note：
Maximum 64 Device in one Subnet。
Maximum Distance for each subnet is 1200 meters。
BUS cable can not be stay together with the electricity cable . If need Parallel cabling way, please make sure that it has 50CM for those 2 types cables.

4. System Important Points for Wiring
Typical Installation

5. Simple System Schematic
10/100M Ethernet
Data Switch
～AC220V
Other
Sunbet
BUS Power
Supply Module
Programming
Module/Converter
Dimming Module
Relay Module
LUX Detect
Sensor
Infrared Motion
Sensor
LCD Panel
6-Gang Switch PC
RS485

6. System Maximum Capacity 255*255= 65025
Subnet ID：0
0-1
0-2 …
0-64
Subnet ID：0
0-65
0-66 …
0-254
System Maximum Capacity 255*255= 65025
Subnet ID：254
254-1
254-2 …
254-64
Subnet ID：254
254-65
254-66 …

7. Solution of Multiple Power system connection

8. dimmer introduction ◆6ch 2A dimmer ( SB-DN-D0602 )
Small dimmer（Din rail mount）
◆6ch 2A dimmer ( SB-DN-D0602 )
◆4ch 3A dimmer ( SB-DN-D0403 )
◆2ch 6A dimmer ( SB-DN-D0206 ) ，

9. Dimmer introduction Load type: AC220V, Resistive load
incandescent lamp
halogen lamp
Led (with driver) …
Attention: electricity-saving lamp & fluorescent light can’t be dim by this type of dimmer.

10. Programming of Dimmer
(SB-DN-D0403)

11. Subnet ID and device ID
Can remark accordingly in order to convenient in maintenance and management.
Device MAC (physical）address
Basical information

12. Control DC Maximum current :100mA
SB-DN-6B0-10V Ballast Dimmer
Wiring diagram L
6 relay switch 16A
ballast N
6 channel direct output switches
Module ID setting button
S-BUS
DC0-10V dimming voltage
Control DC Maximum current :100mA

13. The Relay Module ◆SB-DN-R0810 Relay module ◆SB-DN-R0410 Relay module

14. HVAC Wiring diagram 5 channel output (5A relay)
HVAC is a module specially for Air Conditioner controlling. Coordinate with DLP, it can completely and smartly run an Air Conditioner.
switch 1,2,3
Speed: High/Medium/Low
Mode: Cooling / Heating /Dehumidifier
485总线

15. HVAC
Settings
Delay time setting
1-10V Fan speed control voltage setting

16. HVAC
Settings
AC running test: select AC mode and FAN speed, click ‘Test’ , The HVAC module will run as settings.

17. DLP LCD PANEL Programming
Intelligent control terminal-DLP panel Programming
Front
DLP LCD PANEL Programming

18. INTERFACE FUNCTION DLP Device subnet ID and device ID
Can make remark according to actual location, convenience for maintenance and management
Set the backlight, Higher value make the Great Lightness, And vice versa
DLP
INTERFACE FUNCTION

19. Combination way 1 1 2 3 2 4 Picture A
example：In picture A selected the third (3) combination way . see Picture B key one and key two combined into one key. Then press key one or key two , the effect would be same as press key one .
In picture B , key 3 and key 4 is combined as one key, then press key three or key four , the effect would be same as press key three . In other combination way , Blue part is combine together and set the first key, the white part is independence to control

20. RS485
MS04 Sensor Input wiring.
Sensor input module is used to obtain any external incoming "on / off" signal , to achieve the purpose of external on/off signals controls Smart-Bus. For example if you want to control Smart-Bus via universal 4-way switch, you can use this module to collect On/Off information for each button of the switch, then setup the module.
Sensor
Input
IN1 IN2 IN3 IN4 COM

21. 目录 8 in 1 Sensor ◆8 in 1 Sensor Unique Features
●1 Built in PIR motion sensor
●1 Lux sensor
●2 Dry contacts input
●2 Extemal condition input
●IR(infrared) receiver
●IR(infrared) transmitter
●Built in security alarm logic (work with Security Module)
●Built in 32 Logics

22. 8. Align the Remoter with 8 in 1 sensor, press the key and test
IR Code receiving

23. The using of Infrared Code Learner
1、Connect the Infrared Code Learner with PC via USB port, then install the driver according to the system prompts.

24. 3、Select “Learning mode”
4、Click “Ready for learning the code”，then it is ready to learn the code

25. 红外学习器的使用
5, Put the transmitting terminal of the remote control to the receiving terminal of the Infrared Code Learner, press the button on the remote control, learn it from the following step.

26. 6、按下遥控器按键后，当系统提示“学码成功”即说明该键学习完毕。点击显示已学码，确认有码学入。
红外传感器

27. 7、Put the Infrared Code Learner facing to the device

28. Module address setting button
Advanced Security Controller
Interface of security module ( SB-DN-SEC250K )
Module address setting button
S -BUS

29. Advanced Security Controller
Introduction
work with switches, Sensors, SMS module, Touch screen , the security module can:
1. Accecpt Arm/Disarm commands
2. Received sensor trigger
3. Process data
4. Send out commands by IR sensor/Universal
to realize its fire protection, security, alarm functions.
Security Module
PIR sensor
Z－Audio
SMS Module
Dry Contact
Air Quality sensor
Relay
Dimmer
LCD wall Panel

30. Advanced Security Controller
8in1 sensor(SB-CMS-8in1) security setting
Security ID, area, mode setting

31. Advanced Security Controller
security setting in ms04(SB-DRY-4Z)

32. Advanced Security Controller
Configure keys for security Arm/Disarm in SB-DLP
We can press the keys to arm/disarm.

33. Features
SD card music playing
Internal FM Radio
External audio input
FTP music playing

34. Connection diagrams

35. Step1: find your Z-Audio from S-BUS
Programming
Step1: find your Z-Audio from S-BUS
A SD-card (format by FAT32) is needed to insert into the Z-Audio before power on.

36. Show Controller——DMX Module
Configuration of Show Control ler （DMX Module）
Show Controller——DMX Module
48 Channel——SB-DN-48DMX
240 Channel——SB-DN-240DMX
512 Channel——SB-DN-512DMX

37. System Diagram Configuration of Show Control ler (DMX Module)
Ethernet cable
Ethernet switch
512 channel DMX controller
DMX512 cable
Other effect lights
Computer lighting
Moving heads
Moving heads
System Diagram