1. KX-NS1000
System Structure
Rev Apr., 2015 1

2. Introduction This document explains System Outline and Specification
of the KX-NS1000, and is composed of the following chapters.
Chapter 1 System Outline
Chapter 2 Configuration
Chapter 3 Supported Card /Terminal
Chapter 4 System Capacity
Chapter 5 Hardware Installation 2

3. Table of Contents Chapter1 System Outline
1-1. KX-NS1000 System Overview
1-2. System Connection Diagram
Chapter2 Configuration
2-1. Cabinet Configuration
2-2. System configuration
Chapter3 Supported Card /Terminal 　
3-1. Cards Specification
3-2. Terminal Compatibility
Chapter4 System Capacity
4-1. System Capacity
Chapter5 Hardware Installation
5-1. Items which is used for Main Unit relation
5-2. Main Unit Installation
5-3. Optional Cards Installation
5-4. DOORPHONE Cards installation
5-5. Physical Trunk and Extension Cards Installation
5-6. Mounting Method

4. Chapter 1 System Outline

5. 1-1. KX-NS1000 System Overview
1.Stand-alone System
- A single KX-NS1000 can be used as a stand-alone system.
- A single KX-NS1000 used as a stand-alone system controls all terminals, trunks, and applications.
2.Networked System
KX-NS1000 provides two methods of private networking;
- One-Look Networking (with NS-Net : A network protocol only used for Panasonic products)
- QSIG Networking (via ISDN and H.323)
Slave Units
Master Unit
NS1000 has two type configurations
One is Stand alone system
Another is Networked System
Networked system type has two private netwoking
Onelook
Qsig netowrk
IP Network
・・・
Up to 15 Units
*Refer to the "Networking" part for details.

6. IP/Physical Terminals
1-2. System Connection Diagram
IP/Physical Terminals
Remote PC
IP/Physical Trunks
IP-PT
UT-Phone
3rd party SIP-SLT
Private IP Network
KX-NS1000
IP-CS PS
ITSP*1 Network
IP-Softphone, CA*2 Client PC
Router
Unified
messaging *3
CTI Server
- Analogue Trunk
- BRI Trunk
- PRI Trunk
SLT / FAX
Telephone Company Lines
External Sensor
/External Relay Device
For outside lines, IP trunks and legacy (analog or BRI or PIR) trunks are supported.
For extensions, SIP phones, IP proprietary telephones, wireless phones and single line telephones are supported.
For PC-based software applications, CA (Communication Assistant) is supported.
Connection of other devices such as doorphones and paging systems is supported.
For voice mail or voice messaging, the built-in unified messaging is supported.
OS that is used for NS1000 is based on Linux.
Doorphone & Door Opener
BGM/Music On Hold (MOH)
*1 ITSP: Internet Telephony Service Provider
*2 Communication Assistant
*3 Built-in Main unit
Amplifier / Pager/Speaker

7. Chapter 2 Configuration

8. 2-1. Cabinet Configuration
Front View A
STATUS Indicator B
Master Indicator C
System Mode Switch D
USB Port E
MNT Port F
LAN Port G
WAN Port H
MOH Port I
Doorphone Slot J
Free Slot K
BATT ALARM Indicator L
Pager Port M
Power Switch N
Earth Terminal O
AC Inlet P
Hook Clip Hole Q
MPR ID R
RS-232C Port S
TOP Cover T
Support Bar U
Mother Board A B D E F G J K C H L I
Inside View
Back View S M N P Q R
- RS-232C port
-> using for a factory maintenance
- Dimension: Width 430mm×Height 88mm×Depth 340mm
-> 19 inch-rack mountable (2U)
- Weight (when fully mounted): Under 5.1kg
- Power Consumption (when fully mounted): 50W (240 V: 132 VA, 200 V: 120 VA, 130 V: 104 VA, 100 V: 95 VA) O T U

9. 2-2. System Configuration(1)
Inside
Mother board
Front
DSP cards
DSP-S
DSP-M
DSP-L
Storage Memory
SM-S
SM-M
SM-L
Optional cards
FAX
Outside
DPH1
Line cards
Available cards for NS1000 are explained.
DSP cards : Required to establish any type of call.
Storage Memory cards : Required for recording Voice Messages, etc.
Optional cards : Required to use optional devices.
Line cards : Required to use physical trunks and terminals.
Refer to the following slides for details.
LCOT2+SLC2
BRI4+SLC2
PRI30+SLC2
USB interface
PRI23+SLC2

10. 2-2. System Configuration(2)
DSP (Digital Signal Processor) Cards
To digitally process audio signals, such as a telephone call, the PBX must use a certain number of DSP resources. DSP resources are provided by the DSP cards installed in the PBX. Since there are a limited number of DSP resources, no further operations (e.g., telephone calls, playing an OGM) can be performed if all resources are being used.
There are 3 types of DSP cards.
- DSP-S / DSP-M / DSP-L
The DSP capacity (processing performance) can be expanded.
- Up to 2 DSP cards can be installed to the PBX.
-> The combination of mounting is free.　
The following list shows some of the basic operations that require DSP resources.
DSP is used for almost all services related to voice communication.
Therefore, at least one DSP-S, DSP-M, or DSP-L card must be installed in one of the DSP card slots.
Choose appropriate DSP according to the customer requirement.
- VoIP calls　
- Conferences
- Unified Messaging feature
- DISA /OGM feature
*Refer to the "DSP" part for details.

11. 2-2. System Configuration(3)
SM (Storage Memory) Cards
SM Card is required for using Unified messaging features.
There are 4 types of SM cards.
->SM (installed by Default) / SM-S (:200h) / SM-M (:450h) / SM-L (:1000h)
The Unified Messaging feature can be used with even only SM (installed by default) .
->2ch /2h
If you need to expand the available recording time or available
UM ports, Activation Key is required.
-> The maximum number when expanded :30ch /15h
Storage memory card
Built into Main unit
NS1000 SM
An optional SM card (SM-S, SM-M, -SM-L) is used to expand the capacity of the recording time for Unified Messaging feature.
Install an optional SM card (SM-S, SM-M, -SM-L) as necessary.
*Refer to the "Unified Messaging" part for details.

12. 2-2. System Configuration(4)
USB Interface
USB interface provides communication between the PBX and user-supplied devices such as a UPS or USB memory device.
->The PBX is equipped with a USB 2.0 interface.
Using a USB memory device
A USB memory device can be used to backup and restore the system data of the PBX.
The PBX supports USB memory devices that meet the following specifications:
->File system: FAT /Maximum capacity: 32 GB /Maximum current: 500 mA
Using a UPS
USB interface is used for the following services;
USB memory device connection : System Data Backup / Restore, etc.
UPS connection : Automatic shutdown process for when AC power goes out.
-USB Hub correspondence
-> 実機確認したところUSB Hubは動作する。
但しUSBメモリーとUPSのみ接続可能と説明。
モデルについては確認作業はPSNでは行わず、現場での
確認に任せる。
-> NSからは給電する(500m)。　
-> トレーニングの際の説明に含める。に留めて取説に追記はしない。
A UPS is a device that supplies power for several minutes to a connected device when
a power failure occurs.
*Refer to the “Maintenance" part for details.

13. 2-2. System Configuration(5)
Physical Interface Cards
4 types of Line cards and 1 type of Doorphone card are available for NS1000.
Physical Trunk and Extension cards :
[LCOT2 + SLC2] [BRI4 + SLC2] [PRI30 + SLC2] [PRI23 + SLC2]
For example, if "LCOT2 + SLC2" card is installed in the PBX, 2 analog trunks and 2 SLTs can be used.
[Physical Trunk and Extension Card ]
[DOORPHONE Card]=Doorphone card
- BRI4+SLC2 Card
- LCOT2+SLC2 Card
- PRI30+SLC2 Card
- PRI23+SLC2 Card
Line cards are used to connect physical trunks and extensions.
Choose an appropriate Line card according to the customer requirement.
DPH1 card is used to connect the doorphones and door opener/external relays.
Install the DPH1 card as necessary.
NS1000 has 1 Free Slot for “Physical Trunk and Extension card" and
1 Doorphone Slot for “DOORPHONE card".

14. Main Processing Software
2-2. System Configuration(6)
Virtual cards are included with the Mother board of the NS1000
Virtual cards can be activated with the appropriate activation key.
By installing Virtual Cards in the Virtual Slots of the Mother board using Web Maintenance Console, IP trunks, IP extensions and IP-CSs can be used via the Mother board.
Main Processing Software
on the Mother board
Inside
V-SIPGW16
V-SIPEXT32
V-IPCS4
Virtual Slot
Virtual Cards
V-IPGW16
V-IPEXT32
V-UTEXT32
Virtual cards are used to connect IP Extensions, IP-CSs, and IP Trunks over an IP-Network.
Choose the appropriate virtual cards according to the customer requirement.
Ethernet
Other PBX
IP Telephony
Service
IP-PT
UT SIP-Phone
IP-CS 14

15. 2-2. System Configuration(7)
Activation Key for each Feature
If you want to use the following features, Activation Key is required.
-IP Trunk channel(H.323/SIP)
-IP Telephones capacity
-Number of IP Telephones /Type of IP Telephones (IP softphone/IP-PTs
/SIP Phones (UT series)/General SIP Phones /IP Conferencing Phones)
-Number of Cellular phone
-Unified Messaging related Features / UM port Expansion/・ Notification/2Way-rec user
-Rec Time expansion
-Two-way Rec control Feature
-Message Backup Features
-One Look Networking Feature
-QSIG Enhanced Feature
-CA related Features
-Built-in Router Feature
-VPN features
-Cellular Phone Features
-IP-CS Channel Expansion
-CTI related feature
The appropriate activation keys are needed to use IP-Trunks and IP-Extensions, to upgrade the software for enhanced features, and to use Unified Messaging features, One-look Networking features, CA (Communication Assistant) features, etc.
Activation keys are supplied pre-installed in the mother board and as optional activation key files.
*Refer to the "Activation Key " part for details.

16. 2-2. System Configuration(8)
NS1000 has Preinstalled Activation Key(1)
Preinstalled Activation keys with no expiration date
Activation Key
Activated Features
IP Telephone Capacity
Capacity for up to 30 IP-PTs/IP softphones/
KX-UT series SIP phones/third party SIP phones
CA Basic Express
1022 users
8 IP PT
8 IP-PTs /KX-UT series SIP phones
2 UM Port
2 Unified Messaging ports
Some kind of activation keys are pre-installed.
There are 2 types of Pre-installed Activation Keys ;
“Activation keys with no expiration date” and “Activation keys for free trial (60 days)”
The pre-installed Activation Keys with no expiration date are explained here.
These Activation Keys are available for an indefinite period.

17. 2-2. System Configuration(8)
NS1000 has Preinstalled Activation Key(2)
Preinstalled Activation keys for free trial (60days)
Activation Key
Activated Features
One Look Networking
One-look networking feature
Two-way Recording Control
Automatic Two-way Recording feature
Message Backup
Automatic backup of messages
UM/ (128 users)
128 mailboxes
Two-Way Recording (30 users)
30 Two-way Recording/Two-way Transfer users
Mobile Extension (30 users)
30 cellular phone extensions
CA Pro (128 users)
128 CA Pro users
CA Supervisor (1 user)
1 CA Supervisor user
CA Operator Console (1 user)
1 CA Console user
CA Thin Client Server
Use CA in a thin-client environment
CSTA Multiplexer
Multiplexing for CSTA connections
Activation Key for Call Centre Feature
Enhancement
Queuing information announcement/ACD
Supervisor/ACD Report
Built-in Router
Built-in router feature
16-channel IPsec Activation Key
IPsec connection
The pre-installed Activation Keys for free trial are explained here.
They will expire 60 days after beginning the free trial.
When they expire, the appropriate Activation Key files must be installed to continue to use these features.

18. 2-2. System Configuration(8)
NS1000 has Preinstalled Activation Key(3)
Preinstalled Activation keys for free trial (60days)
Activation Key
Activated Features
Poltys C. Bridge Allows the use of the Poltys C. Bridge.
Poltys CA RCS-Start (5 users) Allows the use of the Poltys CA RCS.*1
Poltys CCAccounting
Allows the use of the Poltys features.
Poltys CCAcc. Enterprise
Poltys CCView
Poltys CCView add. PBX
Poltys CCView Supervisor (5 users)
Poltys CCView CRM P-up (5 users)
Poltys Number notice
Poltys CCAgent (5 users)
Poltys CCRecord SIP (4 ports)
Note
- These Activation Keys are preinstalled on the mother board for the 60-days free trial.
They will expire 60 days after pressing the Activate Pre-installed Activation Key
button to begin the free trial.

19. Chapter 3 Supported Card/Terminal

20. 3-1. Cards Specification(1)
Optional cards are installed on the Mother board
The table of Optional Cards:
Card Type
Model No.
The number
of resources
DSP-S
KX-NS0110
- This card is a digital signal processor card with DSP resources.
The resources are used for VoIP calls, conferences, the Unified
Messaging feature, and the DISA/OGM feature.
- Compliant w/ ITU-T G.729A and G.711 codec methods. 63
DSP-M
KX-NS0111
127
DSP-L
KX-NS0112
254
SM-S*
KX-NS0135
- Storage Memory with maximum of 200 hours Voice Mail recording time.
SM-M*
KX-NS0136
- Storage Memory with maximum of 450 hours Voice Mail recording time.
SM-L*
KX-NS0137
- Storage Memory with maximum of 1000 hours Voice Mail recording time.
FAX
KX-NS0106
- 1-channel fax server. (Interface for FAX signal)
Notes
You must insert these cards to the appropriate slot on the mother board.
ex.) Insert the FAX card to the FAX card slot.
*SM: Storage Memory

21. 3-1. Cards Specification(2)
Virtual cards included with the Mother board
The table of Virtual Cards:
Card Type
Notes
V-IPGW16
Virtual 16 channel VoIP Gateway Card
Virtual Card for 16 channel H.323 trunk.
V-SIPGW16
Virtual 16 channel SIP Trunk Card
Virtual Card for 16 channel SIP trunk.
V-IPEXT32
Virtual 32 channel VoIP Extension Card
Virtual Card for 32 VoIP extensions.
Compliant with Panasonic IP-PTs and IP-softphones.
V-SIPEXT32
Virtual 32 channel SIP Extension Card
Virtual Card for 32 SIP phones except KX-UT series.
(ex. 3rd party SIP phone)
V-UTEXT32
Virtual 32 channel SIP Proprietary Card
Virtual Card for 32 KX-UT series SIP phones.
V-IPCS4
Virtual 4 channel Cell Station Card
Virtual Card for 4 channel CS.
Virtual cards are installed to the main processing software , by using Web MC. 21

22. 3-1. Cards Specification(3)
Physical Trunk and Extension cards are installed for the Free slot
The table of Physical Trunk and Extension Cards:
Card Type
Model No.
Note
LCOT2+SLC2
KX-NS0180
- 2 analogue trunk ports
- 1 power failure transfer (:PFT) port supported 　
- Caller ID Reception supported (FSK/DTMF/Visual CID)
- No Pay Tone supported
- Reverse supported
- 2-Port Single Line Telephone extension
- Caller ID Sending supported (FSK)
- No Message Waiting Lamp control supported
- No CPC Signal Sending supported
BRI4 + SLC2
KX-NS0280
- 4-port ISDN Basic Rate Interface (Euro Ｔｙｐｅ)　
- No PFT port supported
- Same function as NCP1000's BRI(NCP1280)
- Same content as (A)
PRI23 + SLC2
KX-NS0290
- 1-port ISDN Primary Rate Interface
PRI30 + SLC2
KX-NS0290CE
<- (A)
Line cards are used to connect physical outside lines and extensions.
For outside line, analogue lines (COT:LOCT2) and digital lines (BRI:BRI4, PRI:PRI) are supported.
For extensions, analogue extensions (SLT : SLC2) and digital extensions ((BRI:BRI4, PRI:PRI) are supported.
PRI23→KX-NS0290　PRI30→KX-NS0290CE
********************************************************************************************************************
- LCOT2
第1ポートがPFTポートであり設定等で変更することは出来ない。
・局電流診断用リレー回路非搭載の為、BELL信号検知機能とリバース検知機能を利用することにより
局電流診断機能を可能とする。
・下記機能に関しては、NCP Ver.1.0のLCOT4(NCP1180)同等とする。
・Caller ID受信(FSK/DTMF/Visual CID)
・BELL信号検知
・局線捕捉
・選択信号送出（DP送出,DTMF送出,PAUSE送出,FLASH送出）
・CPC信号検知
・リバース検知（リバース応答、リバースCPC）
・局線切断
・着信パルス検知
・アラートトーン検知
・ダイヤルトーン検知
- SLC2
1つのRJ45端子に2台のSLTを接続する。NCPのように中央2芯をポート1に割り当て、RJ11挿しでもSLTが１台動作可能とする。
LCOT-SLCカードの場合、第1ポートがPFTポートであり、組み合わせとなるSLTポートは設定等で変更することは出来ない。
・下記機能に関しては、NCP Ver.1.0のSLC(NCP1173,NCP1174)同等とする。
・OFF/ON HOOK信号検知。
・選択信号検知(DP検知、Flash信号検知、DTMF信号検知)
・BELL鳴動制御(リンギング制御、プレリンギング制御)
・DTMF信号送出
・瞬停処理
- BRI4
【機能仕様】
内線機能対応（内線への給電制御は行わない）
Q-Sig機能
Auto-Config機能
システム同期クロック抽出
LEDによる回線状態表示機能
- PRI30/PRI23
内線機能対応
Q-Sig機能対応
網起動ループバック機能対応（PRI23のみ)
Note - When you would like to remove this card, it is necessary to remove the top cover of a main unit. 22

23. 3-1. Cards Specification(4)
DOORPHONE card are installed for the Doorphone slot
The table of DOORPHONE Card:
Card Type
Model No.
Note
DOORPHONE
KX-NS0161
- 1-port doorphone card for 1 Doorphone, 1 Door Opener
and 1 External Sensor.
- Door Opener Current Limit: 24 V DC/30 V AC, 1A maximum
- OFF HOOK detection supported
- Doorphone connected detection supported
DPH1 card is used to connect the doorphones, door openers, and external relays.
***************************************************************************************************
- DPH1
機能に関しては、TDA30のDPH4及びEIOのセンサー機能同等です。
・OFF HOOK検知。
・ドアホン接続検知。
・特番にて、内線電話機からドアオープナ制御可能。
・特番にて、ドアホンと通話可能。（ドアホン着信）
・ドアオープナ用リレー回路をリンガーとして利用することは出来ない。
・呼び出し可能内線はTDE/NCP同等とし、Web-MCにて設定可能である。
・センサー入力にて、内線呼び出しが可能。
Note
- Non supported HOT-SWAP
- When you would like to remove this card, it is necessary to remove the top cover of a main unit. 23

24. 3-2. Terminal Compatibility (1)
UT Series SIP Telephone
Terminal Type
Note
Standard
Model
KX-UT136
- 6-line Graphical LCD with Backlit
- 24-FF key
- Activation key is required
KX-UT133
- 3-line Graphical LCD with Backlit
Basic
KX-UT123
- 3-line Graphical LCD
- Supported Backlit
KX-UT113
- Non supported Backlit
UT670, UT248
どうする
UT series SIP telephones can be used as extension telephones of the KX-NS1000.
*Refer to the "Terminals" part for details. 24

25. 3-2. Terminal Compatibility (1)
NT 55X Series IP Telephone
Terminal Type
Note
Standard
Model
KX-NT556
- 6-line Graphical LCD
- 36-FF key (Self-Labeling 12x3 w/Back Lit)
- 2 x Gigabit Ethernetports, PoE(Class3)
- EHS(Electronics Hook Switch)
- Connectable Add-on 48 Key Module
KX-NT553
- 3-line Graphical LCD
- 24-FF key (Self-Labeling 12x2　w/Back Lit)
Basic
KX-NT511
- 1-line 16 characters LCD
- Supported Backlit
- Activation key is required
KX-NT551
- 1-line 16Characters LCD
- 8-FF key
- 2 x Gigabit Ethernet ports PoE(Class2)
UT series SIP telephones can be used as extension telephones of the KX-NS1000.
*Refer to the "Terminals" part for details. 25

26. 3-2. Terminal Compatibility (2)
Other supported Terminals
Terminal Type
Note
Portable Station
KX-TCA series
(175,185,275, 285,364,,385)
KX-WT115
- Refer to the "System Wireless" part
for details.
IP-PT
NT3XX Series
- Refer to the "Terminals" part
NT265
- Software version of NT265 is 2.00 or later.
NT54X/NT560
IP Conferencing
Phone
NT700
- When it connects to NS1000 as a SIP
Extension, activation key is required.
SLT
T7710
IP-Softphone
- Activation key is required
Doorphone
T30865
T7765
- It is necessary to install the DOORPHONE
Card (KX-NS0161).
KX-NS1000 supports various types of terminals. 26

27. 3-2. Terminal Compatibility (3)
Un- Supported Terminals
The following terminals can't be connected to NS1000.
Terminal Type
Note
SIP-Phone
HGT100
- Making a call is possible and voice path is
no problem.
- Receiving a call is possible, but there is no
voice.
- Some features such as transfer do not work.
IP-PT
NT400
- It can not be registered. 27

28. Chapter 4 System Capacity

29. 4-1. System Capacity (1) Maximum Optional Service Cards (1)
The following number of cards can be installed in the Physical Slots of the PBX.
Card Type
Maximum Number
Stand-alone System
One-look Network
Physical Interface Card 2 32
Free Slot 1 16
LCOT2+SLC2
BRI4+SLC2
PRI30+SLC2
PRI23+SLC2
Doorphone Slot
DOORPHONE
The maximum number of physical interface cards which can be installed to the KX-NS1000 is shown here.

30. 4-1. System Capacity (2) Maximum Optional Service Cards(2)
The following number of cards can be installed in the Virtual Slots of the PBX.
Card Type
Maximum Number
Stand-alone System
One-look Network
Virtual Trunk Card 16
V-IPGW16
3/3/6 *1 6
V-SIPGW16
16/16/10 *1
Virtual Extension Card 20 32
V-IPEXT32
8/20/8 *1
V-SIPEXT32
20/8/12 *1
V-UTEXT32
Virtual IP-CS Card
V-IPCS4
The maximum number of slots for each slot type is shown here.
*1 Each option can be selected in Easy Setup Wizard 30

31. 4-1. System Capacity (3) Optional Cards Mounted on the Mother Board
The following number of optional cards can be mounted.
Card Type
Maximum Number
Stand-alone System
One-look Network
FAX 1 16
DSP S 2 32
DSP M
DSP L
Storage Memory *1 (Installed by default)
Storage Memory S
Storage Memory M
Storage Memory L
The maximum number of optional cards which can be mounted on the PBX is shown here.
*1 Default: 2ch /2h (*This SM capacity can be extended by the Activation key. [Max.]: 30ch /15h)

32. 4-1. System Capacity (4) Maximum Trunks and Extensions
The PBX supports the following number of trunks and extensions.
Type
Stand-alone System
One-look Network
Total Number of Trunks
256
600
Trunk (Virtual Trunk Card)
H.323 Trunks
48/48/96 96
SIP Trunks
256/256/160
Trunk (Physical Trunk Card) 30
480
Total Number of Extensions
640
1000*1
Extension (Virtual Extension Card)
1000
IP-PT and IP Softphone
256/640/256　*3　
256 x N*2 (upper limit 1000)
SIP Extension
640/256/384　*3
Extension (Physical Extension Card) 2 32
The maximum number of Trunks and Extensions which can be connected to the PBX is shown here.
*1 The maximum number of extension ports is 640 per PBX, and the maximum number of Unified Messaging ports is 30 per PBX. When 30 ports for Unified Messaging are fully activated on the Master unit, the maximum number of extension ports will be less than 640. One Unified Messaging port is equal to 10 extension ports. Therefore, when all Unified Messaging ports are activated, only up to 340 extensions are available.
This condition does not apply for Slave units.
*2 N: The number of Sites (N>=2)
*3 Each option can be selected in Easy Setup Wizard

33. 4-1. System Capacity (5) Maximum Terminal Equipment
The following shows the number of each terminal equipment type supported by the PBX.
Terminal Type
Stand-alone System
One-look Network
Telephone
640
1000
SLT 2 32
IP-PT*1
256/640/256　*3　
256 x N*2 (upper limit 1000)
SIP Phone
640/256/384　*3
Wireless
IP-CS (8-channel) 64
128 PS
512
Doorphone 1 16
Door Opener
External Sensor
The maximum number of Trunks and Extensions which can be connected to the PBX is shown here.
*1 KX-NT300 series, KX-NT265 (software version 2.00 or later only)
KX-NT54X series, KX-NT55X and NT511
*2 N: The number of sites (N>=2)

34. Chapter 5 Hardware Installation

35. 5-1. Before Installation
Unpack the package and check the package contents.
Package Contents
Content
Number
Main Unit 1
CD-ROM (including manuals, etc.)
AC Power Cord *1
19-inch Rack Attachment Bracket 2
Hook Clip
Screw 6
Before installing optional service cards, unpack the package of NS1000 main unit and check the package contents.
*1 The KX-NS1000BX and KX-NS1000XE are supplied with 2 types of AC power cord.
Please use whichever is appropriate for the country/area.

36. 5-2. Main Unit Installation
Open / Close the Top Cover before installation.
Opening the Top Cover
Closing the Top Cover
1. Turn the screws anticlockwise to loosen. \
1. Place the support bar onto the PBX.
2. Slide the top cover then lift it off.
2. Place the top cover onto the PBX.
Then slide the top cover until it closes properly.
In order to install optional cards, it is needed to open the top cover.
When opening the top cover, the power switch must be turned off.
3. Remove the support bar from the PBX.
3. Turn the screws clockwise to tighten.

37. 5-2. Main Unit Installation
Frame Earth Connection.
1. Loosen the screw.
2. Insert an earthing wire (user-supplied).
3. Tighten the screw.
4. Connect the earthing wire to earth.
WARNING
Proper earthing (connection to earth) is very important to reduce the risk to the user of
electrocution or to protect the PBX from the bad effects of external noise in the case of
a lighting strike.
The earthing wire of the AC cable has an effect against external noise and lighting strikes,
but it may not be enough to protect the PBX and to ensure electromagnetic compatibilty.
A permanent connection between earth and the earth terminal of the PBX must be made.
CAUTION
For earthing wire, green-and-yellow insulation is required, and the cross-sectional area of
the conductor must be more than 0.75 mm2 or 18AWG. 37

38. 5-3. Optional Cards Installation
Install the optional cards in the appropriate slot.
Rear
side
Mother Board
SM Card
Slot
DSP
Card
Slot1
DSP
Card
Slot2
Door
Phone
Card
Sｌｏｔ
The mounting positions for each optional card (DSP card, SM card, FAX card) are shown here.
Confirm the positions before installing the cards.
FAX Card Slot
Front
side
CAUTION
When installing or removing the optional cards, the power switch must be turned off.

39. 5-4. DOORPHONE Card Installation
Install a DOORPHONE card in the “Doorphone Slot“.
1. Remove the front cover plate for the Doorphone Slot.
3. Insert the screws into the holes
on the card, and tighten them
to secure the card.
Doorphone Slot
2. Position the card in the open slot, making sure that the tabs
on the both sides of the card fit into place. Then, holding
the card firmly in place, lower the rear end so that the holes
of the card are aligned with the screw holes.
Install a Line card in the free slot of the main unit, according to the procedure shown here.
CAUTION
When installing or removing the DOORPHONE card, the power switch must be turned off. 39

40. 5-4. DOORPHONE Card Installation
Connect a Doorphone to the DOORPHONE Card.
DOORPHONE Card
The method for connecting a doorphone
to the doorphone card.
4Pin
2Pin
To Doorphone
/External Sensor
To Door opener 1 4
<- 2
Doorphone Card
Copper Wire
(ø 0.42 mm to 1.12 mm)
Procedure
1. Strip off the insulation of the wire about 10 mm
from the end.
2. Use a screwdriver to press on the orange tab
at the bottom of the terminal block, and insert
the wire into the upper hole.
3. Check from side to ensure that no bare copper
wire is exposed.
First, install the DOORPHONE card in the appropriate slot of the PBX.
The pin assignments are shown here.
Next, connect a Doorphone, Door Opener, and/or external sensor to the DPH1 card, according to the procedure shown here.
- 4-pin Terminal Block
->Pin1/Pin2 are used for the sensor.
->Pin3/Pin4 are used for the doorphone.

41. 5-5. Physical Trunk and Extension Card Installation
Install a Physical Trunk and Extension card in the "Free Slot“.
1. Remove the front cover plate for the Free Slot.
3. Insert the screws into the holes
on the card, and tighten it
to secure the card.
Free Slot
2. Position the card in the open slot, making sure that the tabs
on the both sides of the card fit into place. Then, holding
the card firmly in place, lower the rear end so that the holes
of the card are aligned with the screw holes.
Install a Line card in the free slot of the main unit, according to the procedure shown here.
CAUTION
When installing or removing the Physical Trunk and Extension card, the power switch must be turned off.

42. 5-5. Physical Trunk and Extension Card Installation
Connect a trunk and/or terminal to the Line cards.
LCOT2+SLC2 Card
PRI23+SLC2 card / PRI30+SLC2 Card
RJ45
To SLT
To Trunk
LEDs
RJ45
To SLT
To NT1/Extension　 A B *1
BRI4+SLC2 Card
RJ45 for SLT
To SLT
To NT1/Extension　
RJ45(LINE1 to LINE 4)
LEDs A B *1
Connect a trunk and/or terminal to the appropriate port of the line card, according to the diagrams shown here.
*1 Select of Switching A/B :
-> A for Trunk (Default) / B for Extension 42

43. 5-6. Mounting Method (1) 19-inch Rack Mounting Attachment Bracket *1
The PBX can be mounted on a 19-inch rack.
When mounting the PBX on a 19-inch rack, only use the 19-inch rack mounting equipment (attachment bracket, screws) included with the PBX.
*1 The 19-inch rack mounting equipment (attachment bracket, screws) included
are included in the same box of PBX.

44. 5-6. Mounting Method(2) Wall Mounting (1) Necessary Items
Included in the PBX
Screw B 6
Included in the wall mounting kit (KX-A247 *1)
Top Bracket 1
Bottom Bracket
Anchor Plug 4
Screw A
The PBX can be mounted on a wall.
When mounting the PBX on a wall, only use the wall-mounting equipment (Screws) included with the PBX and the wall mounting kit(KX-A247).
*1 The wall mounting kit is option.

45. 5-6. Mounting Method (2) Wall Mounting (2)
1. Measure the actual space as indicated below to mark
the 4 screw positions on the wall. Install 4 anchor plugs
in the wall and drive in 4 screws (A) leaving a gap
of 5 mm between the screw head and the wall.
2. Fix the Top Bracket to the left side
of the PBX with 3 screws (B).
Wall Mounting kit
(Optional)
Top Bracket
3. Fix the Bottom Bracket to the right
side of the PBX with 3 screws (B).
The correct
direction.
Main Unit
When placing the PBX onto the wall, refer to the procedure shown here.
In this case, make sure that the arrows on the metal brackets are pointing upward.
If the arrows are not pointing upward, the PBX may fall, resulting in injury.
Front
side
Rear
side
Bottom Bracket
Make sure that the arrows on the metal brackets are pointing upward.

46. 5-6. Mounting Method(2) Wall mounting (2)
4. Place the PBX onto the wall, making sure that
the guide holes hook onto the screw heads.
5. Slide the PBX down into the guide holes.
6. Fully tighten all 4 screws (A).

47. Update History 2015.22 Jun V1.2 The following update
P WAN port Restricted -> Deleted
P11 　 UM Chanel 24ch ->30ch
P AK Added
P UM channel
P29,31 Number of IP-EXT, IP-GW
P32-P33 Number of Terminal
All Page Update for template change
Sep Cabinet Configuration
2-2. System Configuration (7)
3-1. Cards Specification(1)
3-1. Cards Specification(3) Explanation added
3-1. Cards specification(4) Delete for about TDA
3-2. Terminal Compatibility (1) UT248, UT670?
3-2. Terminal Compatibility (2) 185,285,385 added
4-1. System Capacity (2)
4-1. System Capacity (5) NT54,NT55,NT511 added
5-2. Main Unit Installation
5-4. DOORPHONE Card Installation position adjusted
5-5. Physical Trunk and Extension Card Installation
5-6. Mounting Method (1)
5-6. Mounting Method(2) available deleted

48. Thank you ! The END