1. Eclipse HX E-QUE trunking card

2. Eclipse HX E-QUE CARD E-QUE – E1 / Trunking card
E1/T1 card with dual connection to telecom leased lines. Each E1 controller provides 30 digital audio lines.
E1 is a 2Mb telecom standard that allows for 30 digital channels over CAT5 cabling
T1 is a 1.5Mb telecoms standard that allows for 24 digital channels over CAT5 cabling
The E-QUE card conforms to standard telecoms standards, it can be interconnected to 3rd party devices like E1-to-IP muxs, E1-to-Fibre, E1-to-ATM
The ClearCom E-QUE card can be used to pass audio G.711(3Khz) or G.722 (7Khz) across the E1/T1 channel allowing for
Hi-capacity trunklines between matrices
Hi-capacity audio tie-lines between matrices or 3rd party devices that support E1
Matrix A,
Matrix B,
E1 (2Mb) trunklines
Ethernet data
More details are available in the Omega installation manual 2

3. Eclipse HX E-QUE CARD E-QUE – E1 / Trunking card
Note: The E-QUE card is a very versatile card and can be used in a number of different modes.
FreeSpeak mode
E1 – Trunking mode
E1 – Direct 4wire external mode
T1 – Trunking mode
The same card can be used in only one mode
Up to a maximum of 4x E-QUE cards can be fitted into a matrix (in either E1 or FreeSpeak mode)
More details are available in the Omega installation manual 3

4. Eclipse HX E-QUE CARD HX PROGRAMMING
The E-QUE E1/T1 card can be configured using HX
The EQUE E1 card can only be used in Eclipse HX Omega or Median frames
Select the required card type from the Setup matrix hardware screen
Select the Card properties link to change the codec setting
If used for networking 2 matrices – then switch to “My systems” screen and link the E1 cars together
More details are available in the Omega installation manual 4

5. Eclipse HX E-QUE CARD E-QUE – FRONT AND REAR FEATURES
LAN connector for upgrading
E1 connector pin-out
RJ45 #1 for E1 controller
RJ45 #5 for E1 controller
More details are available in the Omega installation manual 5

6. Eclipse HX E-QUE CARD E-QUE – E1 TRUNK AND DIRECT MODES
The E-Que card can be used for both direct E1 to E1 port connections or to provide trunk linking via a network between systems. The E1 connections can be made between Eclipse HX systems or between Eclipse HX systems and compatible third-party equipment.
E1 mode provides 30 channels of G.711 or G.722 encoded audio are available on each port, giving 60 channels per card.
T1 mode provides 24 channels of G.711 or G.722 encoded audio are available on each port, giving 48 channels per card.
The T1 trunking specifications are:
B8ZS Encoding
Long Haul Receive Signal Level
T1 Long Haul (LBO 0 dB) Tx Pulse Amplitude
Balanced RJ45 connection
120 Ohm Line Impedance
No Signalling
G kbit/s Audio Encoding
Tx Clock locally generated
Rx Clock Line Recovered
Extended Super Frame
The E1 specifications are:
HDB3 Encoding
Long Haul Receive Signal Level
E1 120 Ohm Tx Pulse Amplitude
Balanced RJ45 connection
120 Ohm Line Impedance
No Signalling
G kbit/s Audio Encoding
Tx Clock locally generated
Rx Clock Line Recovered
More details are available in the Omega installation manual 6

7. Eclipse HX E-QUE CARD E-QUE – E1 APPLICATIONS
Matrices linked locally by E1 crossover cable
Matrices linked remotely by E1 network (leased lines) via mux
More details are available in the Omega installation manual 7

8. Eclipse HX E-QUE CARD E-QUE – E1 APPLICATIONS
Matrix linked to 3rd party device like a voice recorder or transceiver
More details are available in the Omega installation manual 8

9. Thank you! 9