Presentation is loading. Please wait.

Presentation is loading. Please wait.

Arc ,Rectangular Issued by: Ms.c. Ameer Mosa Thoeny lecture(7)

Similar presentations


Presentation on theme: "Arc ,Rectangular Issued by: Ms.c. Ameer Mosa Thoeny lecture(7)"— Presentation transcript:

1 Arc ,Rectangular Issued by: Ms.c. Ameer Mosa Thoeny lecture(7)
University of Technology Computer engineering and information technology Department AutoCAD lecture(7) Drawing Commands Arc ,Rectangular Issued by: Ms.c. Ameer Mosa Thoeny

2 University of Technology
Computer engineering and information technology Department Command :Arc An Arc is a part of circle; it is a regular curve of less than 360. An Arc is one object. Arcs are always drawn by default in a counter clockwise direction.

3 1) 3 point: Specify three points through which the arc passes
University of Technology Computer engineering and information technology Department 1) 3 point: Specify three points through which the arc passes The Arc command prompt is: Command: arc Specify start point of arc or [Center]: 10, 10 Specify second point of arc or [Center/End]: 20, 10 Specify end point of arc: 10, 20

4 Specify start point of arc or [Center]: 10,10
University of Technology Computer engineering and information technology Department 2) Start, Center, End: The radius is defined by the first two points that you specify. Command: arc Specify start point of arc or [Center]: 10,10 Specify second point of arc or [Center/End]: c Specify center point of arc: 20,20 Specify end point of arc or [Angle/chord Length]: 10,20

5 ARC Specify start point of arc or [Center]: 10,10
University of Technology Computer engineering and information technology Department 3) Start ,Center, Angle: Command: arc ARC Specify start point of arc or [Center]: 10,10 Specify second point of arc or [Center/End]: c Specify center point of arc: 20,20 Specify end point of arc or [Angle/chord Length]: a Specify included angle: 260

6 Specify start point of arc or [Center]: 10,10
University of Technology Computer engineering and information technology Department 4) Start, End, Direction: Command: arc Specify start point of arc or [Center]: 10,10 Specify second point of arc or [Center/End]: e Specify end point of arc: 10,20 Specify center point of arc or [Angle/Direction/Radius]: d Specify tangent direction for the start point of arc:pick 6

7 University of Technology
Computer engineering and information technology Department Exercise: Create the Geometry shown in figure below. Start the first circle center at point 4,4.5 as shown. 7

8 University of Technology
Computer engineering and information technology Department Rectangle: The rectangle command only requires the specification of two diagonal corners for construction of a rectangle. Command: Rectangle Specify first corner point or[chamfer/ elevation/ fillect/thicknss/width] :x,y Specify other corner point: x,y 8

9 A rectangle can have width:
University of Technology Computer engineering and information technology Department A rectangle can have width: Specify first corner point or [chamfer/fillet/width]: W Specify line width for a rectangle <0.0000>: 10 Specify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]: 10,10 Specify other corner point or [Dimensions]: 40,40 9

10 Specify fillet radius for rectangles <0.0000>: 10
University of Technology Computer engineering and information technology Department The fillet option allows you to specify values for the fillet radius at four rectangular corners: Command: rec Specify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]: F Specify fillet radius for rectangles <0.0000>: 10 Specify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]:10,10 Specify other corner point or [Dimensions]: 40,40 10

11 University of Technology
Computer engineering and information technology Department Chamfer option allows you to specify values for the chamfer distances at four rectangular corners: Command: Rec Specify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]: ch Specify first chamfer distance for rectangles <0.0000>: 2 Specify second chamfer distance for rectangles <2.0000>: 2 Specify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]: 10,10 Specify other corner point or [Dimensions]: 40,40 11 11

12 Draw the shape below using rectangle, circle commands.
University of Technology Computer engineering and information technology Department Exercise: Draw the shape below using rectangle, circle commands.


Download ppt "Arc ,Rectangular Issued by: Ms.c. Ameer Mosa Thoeny lecture(7)"

Similar presentations


Ads by Google