1. Operating Instructions for ROFES/MONICOR software
Technology and Operational Details of the ROFES software
Version 3.21
Professional
Diagnostics module
After starting the slide movie press F5 and study the contents of the slides by left clicking for the change of slides.

2. Preparation of the device for work
Before running the program
connect “ROFES” device to the computer’s USB port
Plug the sensor to the
“ECS-ЭХП ” connector
The setup procedure is shown in the video “Preparation of the sensor for work” on the flash-card or the installation disc.

3. START THE PROGRAMM ROFES - MONICOR
Access authorization form
Enter “Login” and “Password”.

4. The “Patient List” form for entering patient’s data will be displayed.
To enter this information, press the “New Patient” button.
Enter Patient’s data and click on the mouse to record.
After entering the personal details, click the “Examinations” button.

5. COMPLETE DIAGNOSTICS
Initial diagnostics
The diagnostics results of one measurement session shall assess up to functional statuses, potential health risks and symptomatic. or

6. the “Selection of mode” form
The frequency compensation process starts, which is the calibration needed for the compensation the environmental electromagnetics . After the frequency compensation has been completed, the “Selection of mode” form will be displayed.
Click the button of the needed diagnostic method in the “Selection of mode” display form.
Start the “ROFES examination (corporeal)” patient diagnostics . Other methods of diagnostic
(“Su Jok examination”, “Verte examination”, “Express examination”)
are performed similarly, but the Points Of Diagnostics will vary.

7. Diagnostic of a patient
Press the button of the “ЭХП-ECS” sensor or the “Examination” button on the display and follow the displayed instructions.

8. Calibration
The setup procedure is shown in the video “Preparation of the sensor for work” on the flash-card or the installation disc. or
1. The edges of a cotton pad may be somewhat extended (1-2 mm), the cotton pad should be profusely wetted with 1% saline solution in a container (glass or cup), to enable the short circuit calibration.
2. Cut a gauze into several pieces or take ready cotton pads (half of a cotton pad) hereinafter cotton pad. Fold cotton pad so that it has 4 layers, wet it with the saline solution, squeeze it a bit so that the solution is not dripping;

9. Calibration or
3. Put the wetted cotton pad on the muscle of the left hand thumb or on the wrist and press it with a passive electrode (“a clamp”). The cotton pad should be in contact with the metal plate inside the passive electrode and 0,5 inch ( 1 cm) of its edges should be seen (see the photo). It can be placed on the forearm (for example for children and women with thin forearms) but not closer than 4  inches (10 cm) to the wrist joint.
4. Wet the ECS sensor head profusely and connect it through the large hole (where a piece of cotton ball is inserted) to the wetted cotton pad, pressed with the clamp on the left wrist. Press the sensor button and release. Wait until the calibration process is completed.

10. the “Selection of mode” form
After the diagnostic process has been completed, go to the “Selection of mode” form
For COMPLETE DIAGNOSTICS
you can start other methods of diagnostics:
“Verte examination”, “Express examination” ( Diagnostics by the point of “correspondence” to pain syndrome). OR
For further analysis of the results of the diagnostics, correction of the patient condition, selection and testing of medical drugs, identification of parasites, color therapy etc., press button “Analysis of examination”
“Su Jouk examination” and “Chakra examination” is Additional methods of diagnostics

11. An electronic Patient Health Record opens up
The electronic Patient Health Record of the patient includes the display windows of all diagnostics and treatments, and provides for monitoring all data.
Press the “Analysis” button of the testing method, which was used for the diagnostic (in our case it is a corporeal method – “ROFES examination”).

12. Results Analysis
This mode is designed to enter a new patient into the framework of the “ROFES-diagnostics” method.
It is launched by pressing the “Harmonious state” key in the “Measurement Interpretation” form view

13. Results Analysis
Two charts will be displayed on the screen:
A referenced harmonious (well-balanced) chart accounting for sex, age and answers to the questions (the left chart);
A patient’s chart according to the results of diagnostics (the right chart);
ROFES Expert shows the patient the ideal condition harmonic chart – the left chart. On the right there is a chart of the actual patient’s condition, accordingly the program will perform the diagnostics analysis and offer algorithms for correction and treatment.
The ROFES Expert presses the “Print” key. Two diagrams and a table of meridians corresponding to diagnosed organs and systems are printed.
This is an entry page of the “ROFES-diagnostics”

14. Results Analysis
Attention! The “ROFES” method of diagnostics is based on the multilevel analyses of the patient measurement data:
Level I.
Evaluation of the patient adaptation mechanism to the environment at the time of this specific time. (evaluation of adaptation resources). Such evaluation includes the evaluation of the functionality of physiological human systems as live bionic mechanism, as well as products of such system, such functionality of the psychiatric activity.
Such evaluation is recorder as Integral Data

15. Results Analysis
The summary of the Integral Data reflects the Harmonious State of the patient as a balance of both, physiology and psychiatry responding to the actual current environment.
To get more information, click button “?” (to the right of the value).
To print, click button “Report”.

16. Results Analysis
Level II. Automatic Expert System
Click on the “Select” against the time of conducted examinations in the “Measurement time” window, the “V” sign will appear
To start the analyses, press “Run expert system (ES)” button

17. Results Analysis
Level II. Automatic Expert System
Expert System offers automated analyses of measurement data.
The Expert System software is based on massive data base of accumulated actual patient examinations by professional doctors and psychiatrists.
Automated Expert System analysis compares this data base with the electrical impedance data of the specific representational points of specific meridians (skin conductivity) and the frequency response data of measured meridians (Spectral analyses).

18. Results Analysis
Stress - status of vital body organs and life support systems
The table displays the Activation Levels of main Life Support Systems stress status)
The vital body organs and life support systems in the table are sorted down according to the Activation Levels. The analysis shall be focused on “Overactivation” and “Hyperfunction” levels (brown and magenta colored with blue frames)

19. Results Analysis
Bookmark “Disease Risks”
Frequency diagnostics evaluates dysfunctions of body organs and systems, or a functional failure of an organ in one of the components of the pathological root-cause chain. It is not known, when and where a diagnostic result is recorded in this chain, but the dysfunction of the body organ would be recorded regardless. Disease Risks or/and symptoms are evaluated by the knowledge-based software. Finally the detected dysfunctions are connected to the specific components of the pathological root cause chain.

20. Results Analysis
Bookmark “Disease Risks”
Accordingly, the anamnestic data, age factor, visual examination, and diagnostics data have to be considered. Depending on such details, the pre-disease status, or risks, or structural changes could be diagnosed.
Among those could be compensated conditions, pre-symptomatic signs and effects, pre-morbidity, or a symptom of calculated symptomatics (considering anamnestic data and Status presents).

21. Results Analysis
Bookmark “Disease Risks”
In case of the pre-morbidity, a ROFES Operator should be aware that unless rehabilitation procedures leading to correction of the detected symptoms are perfomed, the risk of such symptom may vary statistically. There is help available under “Reflexotherapy” for making anamnestic questionary and Status presents”, when hyperactive points are measured for symptoms of ill-being analyses.
Values, higher or equal to 65 are important for analysis (pink, brown and magenta with blue frames).

22. Results Analysis
Bookmark “Specific Analyses”
Clinical and psychological data has been collected. It is designed for professional analyses by physicians or/and psychologists. A professional has a summary of evaluations of stress-statuses of body organs and life support systems, automated diagnostics of disease symptoms. Specific in-depth analysis of all analytics is needed to confirm or reject the analytical data. (cross analyses).
A ROFES Operator edits the textual information. To save the edited information in the “Patient Record”,
click button “Save”.
The degree of the processes is reflected in colors: extreme states – dark-blue and brown.

23. Printed reports for patients

24. ROFES-diagnostics “Visiting list” – after initial measurement: Diagram of harmonious (perfect) state + diagnosed organs and systems (button “Print”). Printing is not recommended on a secondary visit by the patient.

25. 1. Printing from “Expert System” form

26. 2. Print integral assessments and their explanation
2. Print integral assessments and their explanation. Adaptation potential Vegeto-emotional tonus …

27. Attention !
All graphics about diagnostics methods and their analysis is displayed on the screen (see buttons “Print” or “Report” on these screen):

28. Typical usage of the “ROFES” for AWP “Family Doctor”
Initial consultation with a patient
Complete diagnostics of body’s systems and spine’s status. Consulting the diagnostics results.
Additional, if necessary: Testing by nosodes. Remedies selection. Determination of the appropriate rehabilitation processes. Psychological testing and determining hormonal profile. First correction session. Colors’ therapy.
Patient’s next scheduled visit
Express-Diagnostics and Correction”. Purpose:
To quickly obtain Integral Assessments and evaluate patient’s dynamics. To get new spectrum data for selecting corrective treatment. Perform corrective treatment based on measured data. Water treatment. Targeted Color’s therapy – home based
Patient’s next scheduled visit
Express-Diagnostics and Correction”. Purpose:
To quickly obtain Integral Assessments and evaluate patient’s dynamics. To get new spectrum data for selecting corrective treatment. Perform corrective treatment based on measured data. Water treatment. Targeted Color’s therapy – home based
Patient’s repeated visits
Total diagnostics of body’s life support systems and spine for effectiveness evaluation by integrated assessments and by separate body organs and life support systems compared to the initial visit (“Comparative aspect”).
Correcting ways and contents of rehabilitation means.
Additional, if necessary: Testing by nosodes. Remedies selection. Further correction session. Color’s therapy.
Next planned consultations are carried out taking into consideration correction of the ways and contents of rehabilitation means.
And so on, considering patient’s individual features and correcting measures effectiveness.
Other functionality of “ROFES” could be used based on patient’s needs, , ROFES Operator skills, views and background.

29. Some case analyses of ROFES usage accumulated since 1995
Sport medicine
Steadily high athlete’s Adaptation Potential while training for competition, it is a guarantee of winning one of the awards.
Recruitment, access control
Steadily low Adaptation Potential of a candidate during several ROFES measurements means that the person will have difficulties in meeting his commitmentss at work even if he is a quality professional. He will spend more of his efforts and energy than a professional with high Adaptation Potential. Consequently, people with low Adaptation Potential are in the high risk group dealing with complicated assignments, particularly in hazardous processes.
Such and many other trends are included in the ROFES software, and are studied during the seminars.

30. Some case analyses of ROFES usage accumulated since 1995
ROFES can help on-site medical psychotherapists to perform the following:
Monitor personnel’s functional and emotional condition to prevent nervous breakdowns, and check-ups prior high risk assignments;
Screening for psychological compatibility in groups (sport, professional), crews;
Screen for tendency to anti-social behavior patterns (suicide, drugs), as well as those in need of psychotherapy;
The recommendations below can be used by medical doctors or psychologists.
This express-diagnostics can be used in hospitals, doctor offices, rehabilitation facilities, health and preventoriums clinics, and also by family doctors and acupuncturists.
Additionally, ROFES can be used at educational institutions to evaluate the impact of students’ work load on their psychophysiology.