Download presentation
Presentation is loading. Please wait.
1
Pressure Vessel Inspection Techniques
Stan Botten
2
Introduction FACTORS TO BE CONSIDERED. MATERIAL SELECTED
DESIGN PRESSURES MAXIMUM ALLOWABLE DISCONTINIUTY PRODUCTION ACCESSABILITY ENVIRONMENTAL LIMITATIONS INSPECTABILITY DAMAGE MECHANISM
3
List of NDE methods LIQUID PENETRANT (PT) MAGNETIC PARTICLE (MT)
RADIOGRAPHY (RT) DIGITAL (DRT) ULTRASONIC (MUT) AUTOMATED ULTRASONIC (AUT) EDDY CURRENT (ET) ACOUSTIC EMISSION TESTING (AET)
4
Liquid Penetrant (PT) LIMITATIONS : OPENING TO SURFACE MINIMUM 1.9 MICRONS SURFACE BREAKING DISCONTINIUTIES ONLY. ADVANTAGE: LOW COST SEMI SKILLED.
5
Magnetic Particle (MT)
6
Limitations & Advantages of MT
Limitation: Surface and near surface only Indication must exceed 16 microns deep No permanent record. Need full access to area to be inspected. Advantage: Semi skilled labor, Low cost
7
Radiography (RT) Digital (DRT)
8
Digital image Weld flaw
9
Limitations of RT /DRT 2% of material thickness Flaw orientation
Special facilities Radiation Hazard. Skilled labor required. Processing time (Film) Storage if Film used
10
Ultrasonic flaw detection (UT)
There are three major techniques for Ultrasonic flaw detection. Manual scanning of inspection area (MUT) Phased Array both automated and manual scanning (MUT & AUT) All techniques suffer from the same limitations The major differences being the computerized recording of the results
11
Ultrasonic Inspection (Pulse-Echo)
High frequency sound waves are introduced into a material and they are reflected back from surfaces or flaws. Reflected sound energy is displayed versus time, and inspector can visualize a cross section of the specimen showing the depth of features that reflect sound. f 2 4 6 8 10 initial pulse back surface echo crack echo crack plate Oscilloscope, or flaw detector screen
12
SOUND TRAVEL GEOMETRY Discontinuity obliquely oriented to the test surface: angle beam transducer
13
Limitations of UT Coverage: In order to inspect 100% of the area every square mm of the area of interest must be scanned The smallest flaw detectable is governed by the transducer frequency and the material being inspected. The laws that govern this is ½ the wave length or 3 times the material grain size which ever is the larger, typical carbon steel with a 4 Mhz transducer would be 1 square mm. The orientation of the flaw in relation to the UT beam is important for the detection. At least one clean surface must be accessible Highly skilled operators are required for good results.
14
COMPUTER CONTROLLED TRANSDUCER
Typical UT Parameters Controlled Scanning Angle Focal Distance Focal Spot Size
15
ADVANTAGES OF PHASED ARRAY UT
Control of Beam Parameters Multiple Angel Inspection With One Probe Inspect Complex Geometries Easily Multiple Configurations P/E, P/R, TOFD Better S/N Ratio LIMITATIONS OF PHASED ARRAY UT Same as Conventional Shear Wave UT Large transducer size
16
EXAMPLES OF WELD DEFECTS
Presentation of the different types of defects found in welds using X-ray, TOFD and Phased array techniques
17
Root Crack Radiography Phased Array technique TOFD technique
18
Porosity Radiography Phased Array technique TOFD technique
19
Slag inclusion Radiography Phased Array technique TOFD technique
20
Eddy Current Testing Crack Coil's Coil magnetic field Eddy current's
Conductive material
21
Limitations of Eddy Current (ET)
Surface breaking flaws only Full area must be scanned Smallest Flaw is 3 x surface roughness Skilled operator required Weld inspection only possible if surface ground flush Calibration standards with EDM notches required.
22
Definition of Acoustic Emissions
“The class of phenomenon where transient elastic waves are generated by the rapid release of energy from localised sources within a material, or the transient elastic waves so generated.” SNAPPING OF TWIGS – Tin Cry Bindschadler, R., W.D. Harrison, C.F. Raymond and R. Crosson. “Geometry and dynamics of a surge-type glacier.” Journal of glaciology. Vol. 18 (1977):
23
Acoustic Emission Detection
Electrical Signal Stress Waves Acoustic Emissions Sensor Flaw LOADING
24
Actual AE signal of crack in carbon steel
25
Lead-Breaks Hso Nealson AE source 0.5mm 2H lead Lead breaks
Material Stressed Producing AE signal in material
26
Data Analysis (Signal Parameters)
Amplitude Five Measured Parameters Counts threshold Rise Time Duration Relative Energy Signal Strength
27
Data Analysis (Calculated Parameters)
Average Signal Level (ASL) Burst type activity Low ASL (Crack Activity) Continuous noise High ASL (Leak Activity)
28
Stress strain curve Stress concentration YEILD 60% YEILD
ONSET OF AE ACTIVITY Stress concentration CRACK SITE NORMAL STRESS 5% UY STRESS CONCENTRATION > 60% OF UY
29
Location of defect PLANAR LOCATION SENSOR LOCATION SHOCK WAVE SOURCE
LOCATION T1-T2
30
PRESSURE VESSEL REMOVED FOR AE SENSOR PLACEMENT
AE sensor locations
31
1,000 PSI 15,000 PSI HOLD AT 19,500 HOLD AT 25,500 HOLD AT 30
1,000 PSI 15,000 PSI HOLD AT 19,500 HOLD AT 25,500 HOLD AT Start to increase to 33,000 Pressure stopped 1,000 PSI 15,000 PSI HOLD AT 19,500 HOLD AT 25,500 HOLD AT Start to increase to 33,000 Pressure stopped
32
TEST CORELATION PLOTS
33
Planar location of AE activity
Crack area
34
Linear location on circ. weld
35
Cracks located on jacket to shell weld.
36
Thank You
Similar presentations
© 2025 SlidePlayer.com. Inc.
All rights reserved.