Download presentation
Presentation is loading. Please wait.
1
The Engineering of Foundations
lecture 5 Definition of Foundations Types of Foundations Bearing Capacity of Shallow Foundations
2
Definition of Foundation
Foundation is the lowest portion of the structure which exists below the earth surface. It refers to the material whose behaviour the civil engineer has analyised in order to provide satisfactory and economical support to the structure. Although out of sight, the foundation is nonetheless important because if it is deficient in design or construction, the entire building is at risk, Leaning Tower of Pisa, Italy, is a classical example.
3
Definition of Foundation
Functions of Foundation The main function of the foundation is to transfer the load of the structure to the strata on which it is resting. Important Considerations The most important considerations in foundations design: foundations must be stable against shear failure Must not settle beyond tolerable limit to damage the structure.
4
Types of Foundations There are mainly two types of foundations depending on the nature of sub-soil strata and type of superstructure. Shallow Foundations These foundations are made where the structural loads are carried by the soil or rock directly under the structure. The ratio of depth to the width of the footing usually in a range less than 1 (Df/B ≤ 1). Some of commonly used foundations: Spread footings Mat footings
5
Some common types of shallow foundations
Types of Foundations Some common types of shallow foundations Df B B (a) Spread Footing (b) Mat Footing Df L (c ) Combined Footing Fig. 1 Some common types of shallow footings
6
Types of Foundations Deep Foundations
These foundations are used to transfer the load of the structure to a depth where sufficient support is available if the top soil is weak. In these foundations Df/B > 1. Some of commonly used deep foundations: Pile foundations Tapered piles Belled piles
7
Some of common types of deep foundations
Types of Foundations Some of common types of deep foundations (a) Pile foundation (b) Tapered pile (c) Belled pile Fig. 2 Some common types of deep foundations
8
Bearing capacity of shallow foundations
Bearing capacity can be defined as the limit load which when applied to the footing causes it to plunge into the ground or settle by very large amount. The effects of increasing the load on the footing is as follows: Elastic settlement Footing experience further settlement as the soil enters the plastic range the footing edges. (a) (b)
9
Bearing capacity of shallow foundations
Settlement continues as the plastic zone increases Settlement may become large as the plastic zone expands but flow continues to be constrained by the surrounding elastic zone. Unrestrained flow occurs when the plastic zone extends to the surface of the soil mass. (d) (e) (c) Fig .3 effects of increasing loads on shallow foundations
10
Bearing capacity of shallow foundations
Three possible patterns of failure are expected to occur when the applied load reaches the ultimate limit state. General shear failure in this case a triangular wedge-shaped zone of soil marked (I) is pushed down and in turn it presses the zone marked (II) and (III) side ways and then upward, at the ultimate pressure, the soil passes into a state of plastic equilibrium and failure by sliding. Dense sand with relative density > 70% and stiffer clay. Fig. 4 General shear failure
11
Bearing capacity of shallow foundations
Local shear failure In the case of local shear failure, the triangular wedge shaped zone of soil (marked I) below the footing moves downward, but unlike general shear failure, the slip surface end somewhere inside the soil. However, some signs of soil plunging are seen. Loose to medium sand with relative density 35-70% and soft clay. Fig. 5 Local shear failure
12
Bearing capacity of shallow foundations
Punching shear failure in the case of punching shear failure, foundations penetrate into the soil without any plunging of the surface. The failure surface never reaches the surface. Relatively loose sand with relative density less than 35%. qu B Fig. 6 Punching shear failure
13
Bearing capacity of shallow foundations
Terzaghi’s Bearing Capacity Equation Terzaghi (1943) extended Prandil (1921) theory His equation was developed on strip footing with L/B > 5. Depth of footing to the width ratio less than 1 Weight of soil above the base of footing may be replaced by uniform surcharge q0 = ϒ Df Footing base is rough Type of failure is general shear
14
Bearing capacity of shallow foundations
Terzaghi’s Bearing Capacity Equation Zone I: wedge ABJ elastic zone Zone II: AJE, BJD radial shear zone Zone III: wedge AEG and BDF Rankin’s passive zone JD and JE are arcs of logarithmic spiral DF, EG straight line Fig. 7 Terzaghi bearing capacity analysis Let us imagine that AJ and BJ are two walls that are pushing the soil wedges AJEG and BJDF, respectively, to cause passive failure.
15
Bearing capacity of shallow foundations
Terzaghi’s Bearing Capacity Equation Pp should be inclined at angle δ, wall friction to the perpendicular drawn to wedge faces. In this case δ = ϕ. As AJ and BJ are inclined at ϕ to horizontal, Pp should be vertical. Considering the equilibrium of wedge ABJ per unit length . Fig. 8 Terzagi’s bearing capacity analysis the forces affecting on elastic wedge
16
Bearing capacity of shallow foundations
Terzaghi’s Bearing Capacity Equation (1) Where; b = B/2; w = weight of soil wedge ABJ = b2ϒtanφ; C = cohesive force acting along each face, AJ and BJ that is equal to the unit cohesion times the length of each face C = cb/cos φ . Thus, (2) (3)
17
Bearing capacity of shallow foundations
Terzaghi’s Bearing Capacity Equation The passive pressure in the previous equations is the sum of the contribution of the weight of the soil, ϒ, cohesion, c, and surcharge, q0. (c) Surcharge contribution Soil contribution (b) Cohesion contribution Fig. 9 Passive force distribution on the wedge face BJ
18
Terzaghi’s bearing capacity equation
Thus, we can write: (4) Where kϒ, kc, k0 are earth pressure coefficients that are functions of soil friction angle, φ. Note: H = b tanφ Combining Eqs. 3 and 4 we obtain: (5)
19
Bearing capacity of shallow foundations
Terzaghi’s Bearing Capacity Equation (6) (7) (8) The terms Nc, Nq and Nϒ are respectively are the contributions of cohesion, surcharge and unit weight of soil to the ultimate load bearing capacity
20
Bearing capacity of shallow foundations
Terzaghi’s Bearing Capacity Equation It is extremely tedious to evaluate kc, kq and kϒ, Terzaghi gave the following equations for bearing capacity factors. (9) where; (10) (11)
21
Bearing capacity of shallow foundations
Terzaghi’s Bearing Capacity Equation For square and circular footings, Terzaghi suggested the following equations for ultimate soil bearing capacity. (square) (12) (circular) (13) In the case of local shear failure it is assumed: c = 2/3 c and tan φ = 2/3 tan φ. For undrained condition φ = 0, = c, the bearing capacity factors become Nϒ = 0, Nq = 1, Nc = 5.7
Similar presentations
© 2025 SlidePlayer.com. Inc.
All rights reserved.