Download presentation
Presentation is loading. Please wait.
1
General Body Electric/Electronic
Welcome to General Body Electric/Electronic Philipp Gruber
2
LM (Light Module)
3
LM Functions: Controling and monitoring of the exterior lights
Dimmer-function Communication with the trailer module Emergency functions Headlight adjustment Evaluation of the information rain-/light sensor
4
LM Light Control FLC
5
LM Ambient Light Sensor Front Light Sensor Detection of:
twilight/darkness bridge/tree-lined avenue tunnel/garage No detection of: fog smog/smoke
6
LM Headlight Adjustment Manual LWR Automatic LWR Dynamic LWR: correction of driving situations as strong deceleration strong acceleration
7
LM Speed depending headlight level
8
LM dynamic compensation by acceleration dynamic compensation
by deceleration
9
Interior Lighting
10
Interior Lighting Interior lighting is controled by
the means of the power module 3 circuits: IB: interior lighting VA-D: consumer shut-off roof VA-K: consumer shut-off body
11
Interior Lighting door warning lamp boarding lamp ambient light vicinity lighting
12
CAS (Car Access System)
13
CAS The CAS combines the up to now separate installed components - ignition starter switch - vehicle immobilization system EWS - functions of the control electronics
14
CAS The ignition starter switch is the electro-mechanical part of the CAS The switch exists of ignition lock with electro-mechanical release lock - start/stop button - coil for checking the transponder and for charging the accumulator (battery)
15
CAS The CAS is the electronical part The CAS is connected with - door modules - seat modules - power module The CAS has Master-functions for - central locking - power windows The CAS controles - remote control - terminal monitoring - EWS - engine start - starter control
16
CAS Vehicle Key
17
CAS Terminal selection if brake is not activated terminal 30
terminal R terminal 30 terminal 15
18
CAS The engine can be started in all terminal selections, if
- the brake is activated - P- or N-position is detected The engine will stop running, if - the car stands and the start/stop button is pressed After the engine stops the terminal „R“ is active
19
CAS EWS-Functions
20
CAS The vehicle order in the CAS - replaces the central coding key, ZCS - describes the current version of the vehicle - varys in length depending on vehicle equipment The vehicle order will be sored in the vehicle together with the pre-initialization in the factory plant
21
CBS-Data (Condition Based Service) CBS-Data are stored
CAS CBS-Data (Condition Based Service) CBS-Data are stored - in the remote control - in the EEPROM of the CAS Data stored: - configuration of the CBS - vehicle identification number VIN - type of vehicle - FA-Data - dealership coding - current vehicle version - CBS-Data - check-control-data - fault memory data
22
CAS Redundant Data Storage To make sure that in the event of replacing the instrument cluster the vehicle specific data will not get lost, those data are stored redundant in the CAS.
23
FH (Power Windows)
24
FH List of Functions -closing and opening of the windows -child safety lock -comfort opening/closing -repetition lock -high load shut-off New: -emergency close -smooth start / smooth stop -motor synchronization -indirect jam protection
25
FH
26
FH Smooth Start Smooth Stop
27
FH Emergency Close Phase 1: - hold the position „CLOSE“ and keep it if jam protection is detected the window opens for 20 mm Phase 2: - release the switch and within 4 s hold it in the position „CLOSE“ again - window closes without jam protection with maximum power
28
FH Indirect Jam Protection
29
FH Initialization - press switch FH open for 15 –25 s - release switch and close the power window immediately – initialization starts - keep the switch hold until the end of the initialization
30
Central Locking (ZV) and Soft Close Automatic
31
Central Locking (ZV) and Soft Close Automatic
New (only US): single unlocking via center lock switch (CLT)
32
Central Locking (ZV) and Soft Close Automatic
Soft Close Automatic (SCA): door lock with integrated drive Drive can take 2 positions: - stand-by position - park position
33
FBD (Remote Control)
34
FBD Remote Control ZV (central locking) Tele-start hand sender Integrated Universal Remote Control
35
Integrated Universal Remote Control -replaces up to 3 hand sender
FBD Integrated Universal Remote Control -replaces up to 3 hand sender -signal of the original hand sender must be programed on the buttons of the remote control -system runs only with remote frequency -transmission of the signal is displayed by the LED program buttons LED
36
HKL (Tailgate Lift)
37
HKL Operating Points TOEHK tailgate button, exterior TOEHKI
tailgate button, interior passenger compartment FBD (remote control) TOEHKK tailgate button, interior
38
HKL Tailgate Run tailgate open, top stop point top switch-off point
lower switch-off point tailgate closed
39
HKL Tailgate Run rotating angle sensor (Hall-sensor)
40
HKL Repetition Lock
41
HKL Hydraulic Unit System pressure 100 bar System is - maintenance-free - self-bleeding
42
Electrical Roller Sun Blind
43
Electrical Roller Sun Blind
rear sun blinds are optional 2 sun blinds at each door rear roller sun blinds only together with rear screen roller sun blind (option)
44
Electrical Roller Sun Blind
45
Electrical Roller Sun Blind
Functions: Release of the rear sun blind operation is connected with the release of the power windows. Roll out of the side sun blinds just when side window is closed, roll in is always possible.
46
Refrigerator Box
47
Refrigerator Box Refrigerator box in the rear is optional equipment Thermo electrical refrigerator box with Peltier-Elements
48
Peltier-Element (function principal)
Refrigerator Box Peltier-Element (function principal) heat exchanger warm side blower PE-seal Peltier-Element aluminium solid blower cold side isolation heat exchanger cold side housing
49
activated/deactivated by the means of a switch
Refrigerator Box refrigerator box is activated/deactivated by the means of a switch current draw temperature current draw depending on difference in temperature
50
Refrigerator Box Economy Mode
51
Seat- /Mirror- /Steering Column-Functions
52
Seat- /Mirror- /Steering Column-Functions
Front Seat Versions - basic seat with electrical adjustment - comfort seat with driver and passenger seat memory Additional Optional Equipment - seat ventilation - active seat - memory-function (drivers seat only) - lumbar support - seat heating
53
Seat- /Mirror- /Steering Column-Functions
Rear Seat Versions - basic seat - comfort seat with memory function Additional Optional Equipment - seat ventilation - seat heating
54
Seat- /Mirror- /Steering Column-Functions
Outside Mirror Versions - electrochromic mirror - mirror memory Steering Column Adjustment There is just one fully electronical version.
55
Seat- /Mirror- /Steering Column-Functions
56
Seat- /Mirror- /Steering Column-Functions
Basic Seat Seat length adjustment Seat tilt adjustment Seat height adjustment Seat backrest adjustment Adjustment of the seat headrest is a connected function with the seat length adjustment.
57
Seat- /Mirror- /Steering Column-Functions
Seat Heating 1 – quick heating field 2 – residual heating field 4 – seat cushion 3 – seat backrest
58
Seat- /Mirror- /Steering Column-Functions
Balance Control Temperature difference between seat cushion and seat backrest adjustable. Adjustment remains stored via key-memory.
59
Seat- /Mirror- /Steering Column-Functions
Seat Ventilation
60
Seat- /Mirror- /Steering Column-Functions
Seat Modules 2 different module sizes 8-module connectors 10-module connectors for active seat or lumbar support
61
Seat- /Mirror- /Steering Column-Functions
Steering Column Adjustment
62
DWA (Anti Theft Alarm System)
63
DWA Components Interior sensor with integrated DWA-Logic
DWA-LED Interior sensor with integrated DWA-Logic Emergency siren with tilt alarm sensor External Switches
64
DWA
65
DWA Emergency Siren with integrated Tilt Alarm Sensor -emergency siren gives out acoustic alarm -communicates with interior protection via DWA-K bus -separate power supply -monitors power supply of the vehicle battery -monitors manipulation on all input wires -tilt alarm sensor monitors horizontal position -sends alarm telegram to DWA-interior protection if tilt change is detected
66
DWA Interior Sensor with integrated DWA-Logic -ultrasonic interior protection -controled by integrated DWA-Logic -alarm telegram via K-CAN S or DWA-K bus
67
DWA Diagnosis -alarm and info memory are non-volatile -alarm memory with additional information Service Tip: -DWA-quick test possible -alarm just for 2 s -loudness reduced
68
SHD (Slide-/Tilt Sunroof)
69
SHD Panic-Close Phase 1: -keep position „CLOSE“ -if jamming is detected the sunroof opens 20 mm Phase 2: -release switch and within 1,5 s activate position „CLOSE“ again -SHD closes without jam protection and maximum power
70
SHD Initialization - press operating switch in position „TILT“ and keep it - after 15 s the drive runs in position „TILT“ - in position „TILT“ the motor stops for 5 s and runs subsequent in the position „CLOSE“ - subsequent the motor runs in the end position „OPEN“ and turns back in the position „CLOSE“ - keep the switch pressed during the whole procedure
71
WIM (Wiper Module)
72
WIM New developed wiper system Advantages: -wiper frequency independent of differences between the wiper motors -wiper angle improved -wiper arm speed dependent on wiper arm position –reduced size -safe against overload -alternating park position of the wiper arms
73
WIM
74
WIM Components of the Wiper Drive -reversable motor -reduction gear -gear housing cover with interated wiper module -connector
75
WIM Components of the Wiper Module -final drive for wiper motor washer pumps heating of the water tube in the wiper arm -3 Hall-sensors -CAN interface -control unit
76
WIM Rain-/Light-Sensor
77
WIM Heating of the water tube in the wiper arm -water is electricaly heated in the wiper arm -heating element at the lower end of the wiper arm
78
WIM Functions: Wiper positions: depending on the function different positions are possible
79
WIM Functions: Alternating Park Position APS:
-park position dependent on the wiper position -with „INTERVAL“ higher position than with „OFF“ -park position in „OFF“ changes every 4 days
80
washer jets are not adjustable
WIM Functions: Washer jet cleaning function - wiper arm in park position - terminal R off - press wiper switch within one minute at least 3 s Washer pump works - pulswide with full load - max. 30 s - no wiper arm movement washer jets are not adjustable
81
PDC (Park Distance Control)
82
PDC Firstly launched in 1991 in the E32. The PDC in the E65 is a further development of the E38 PDC. The principal functions are taken over from the PDC-systems since MY 98. New: - acoustical distance warning with the audio speakers - optical distance warning via CD - information about faults in CC and CD
83
PDC
84
PDC Acoustical PDC-Warning
85
PDC Optical PDC-Warning
86
RDC (Tyre Pressure Warning System)
87
RDC Principal functions of the system are equal to the existing system. New: The controller replaces the „SET-Button“.
88
RDC
89
RDC Initialization During the initialization the CC-Message
„RDC is being initialized“ is displayed in the instrument cluster. After completing the tyre pressures of each tyre will be displayed in the CD.
Similar presentations
© 2024 SlidePlayer.com. Inc.
All rights reserved.