2. UNICO INVERTER DC

3. UNICO INVERTER DC
The first INVERTER technology based heat pump without external unit on the market
The new product will be available in 4 different models
1. UNICO INVERTER DC 9 SF
2. UNICO INVERTER DC 9 HP
3. UNICO INVERTER DC 12 SF
4. UNICO INVERTER DC 12 HP

4. UNICO INVERTER DC Main technology innovations Design (King & Miranda)
1. Outstanding quiet operation
2. High performance and efficiency
3. High air flow and air distribution
4. Installation
Reduced installation time needed
High and low installation configuration
5. Easier maintenance
6. Advanced air filters
7. Low ambient control
Design (King & Miranda)

5. + = 1 – OUTSTANDING QUIET OPERATION Unico Inverter DC
1 Unico Star
The new Unico Inverter DC’s noise level will be half the current UNICO Star

6. = 2 – HIGH PERFORMANCE DC INVERTER Technology
The inverter control system constantly regulates the compressor motor speed, adapting it to the actual cooling or heating needs of the room
Inverter technology
Max
Comfort =
Keeps the set temperature without oscillations
Reaches the set temperature faster
Low energy consumption (reduction up to 30%)
Low noise level

7. 2 – HIGH PERFORMANCE

8. 2 – HIGH PERFORMANCE

9. Cooling UNICO INVERTER vs Competitors
2 – HIGH PERFORMANCE
Cooling UNICO INVERTER vs Competitors
Classe A
EER Kw

10. 2 – HIGH PERFORMANCE Heating UNICO INVERTER vs Competitors Classe A
Classe B
COP Kw

11. 3 – HIGH COMFORT INCREASED AIR FLOW IMPROVED AIR DISTRIBUTION 520 cm/h
The air distribution has been improved increasing the size of the air outlet to 690 x 60 mm

12. 4 - INSTALLATION UNICO INVERTER UNICO STAR
Can be installed high wall or low wall
Can be installed high wall or low wall
FOR HIGH WALL INSTALLATION
Change the position of the air outlet flap, and press a key on the LED panel
FOR HIGH WALL INSTALLATION
Dismount plastic shell
Invert position of air outlet parts
Move LED and fan cap
Installazione bassa
TIME NEEDED
1 minute
TIME NEEDED
20 minutes
Installazione alta
Particolare flap uscita aria

13. 4 – INSTALLATION
Suggested holes are of 202 mm Ø for higher performances, but the unit can works with 162mm Ø holes as well.
Unico Inverter DC back

14. 4 – INSTALLATION
It is very easy to operate the unit with 200 mm holes. The unit is factory fitted to work with 160 mm holes, if necessary.
First hole: remove the pre-cut plastic
Second hole: behind the rear panel there is a polistyrene cylinder that reduces the size of the hole. Simply remove it.
The distance between the center of the holes remains the same as the UNICO Star. This easily allows replacing old Unico Star units with the new Unico Inverter.

15. 4 – INSTALLATION
The minimum top/bottom and side allowances have been reduced. Unico Inverter can be installed in small niches where it was not possible to install Unico Star.

16. 5 – Easier maintenance
The accessibility to the internal parts have been improved. It is easier to dismount and service the single components of the unit.
REAR PART
FRONT PART

17. 5 – Easier maintenance REAR PART
The back of the unit is made by two panels
LEFT PANEL
Encloses the:
- coil zone
- compressor
- drain exhaust system
RIGHT PANEL
Encloses the condenser fan group,. Removing some screws the whole fan group can be removed to be more easily serviced.

18. 5 – Easier maintenance FRONT PART
The front part has a big frontal panel. When you remove it, you find two smaller panels.
LEFT PANEL
Removing it you can access to the electric board
RIGHT PANEL
Removing it you can access to
- compressor
- external coil probe
- drain exhaust system

19. 6 – ADVANCED AIR FILTERS
Electrostatic filter: removes small particles and smoke, dust, pollen, pet hair, preventing allergy issues
Active carbon filter: removes smells and deactivates harmful gases
Cleaning: The air inlet grills are very easy to dismount
Air inlet-outlet flaps closed
Air inlet-outlet flaps open

20. This makes UNICO a perfect solution for server rooms.
7 – LOW AMBIENT CONTROL
UNICO Inverter can work in cooling mode with outside temperature up to -10C°!
This makes UNICO a perfect solution for server rooms.

21. TECHNICAL DATA Unico inverter 12 SF Cooling capacity (min-nom-max)
1800 – 2700 – 3100 Watt
Heating capacity /
E.E.R.
2,7
C.O.P.
Cooling energy efficiency class A
Heating energy efficiency class
Size in mm (wxhxd)
902 x 506 x 230
Weight (kg) 40
Walls hole size
Noise level
TBD
Unico inverter 12 HP
Cooling capacity (min-nom-max)
Watt
Heating capacity
Watt
E.E.R.
2,7
C.O.P.
3,2
Cooling energy efficiency class A
Heating energy efficiency class
Size in mm (wxhxd)
902 x 506 x 230
Weight (kg) 40
Walls hole size
Noise level
TBD
Unico inverter 9 SF
Cooling capacity (min-nom-max)
1400 – 2300 – 2700 Watt
Heating capacity /
E.E.R.
2,7
C.O.P.
Cooling energy efficiency class A
Heating energy efficiency class
Size in mm (wxhxd)
902 x 506 x 230
Weight (kg) 40
Walls hole size
Noise level
TBD
Unico inverter 9 HP
Cooling capacity (min-nom-max)
1400 – 2300 – 2700 Watt
Heating capacity
1400 – 2400 – 2700 Watt
E.E.R.
2,7
C.O.P.
3,2
Cooling energy efficiency class A
Heating energy efficiency class
Size in mm (wxhxd)
902 x 506 x 230
Weight (kg) 40
Walls hole size
Noise level
TBD
NB: all the data shown in this presentation must be considered as preliminary

22. ACCESSORIES IN THE BOX TEMPLATE 2 INTERNAL FLANGES
PAIRS OF EXTERNAL GRILLS (200 mm)
NEW PP SHEETS TO USE FOR 200 mm HOLES (but suitable for 160mm holes as well)