1. NSX1000/2000 V2.0 - Simultaneous Maintenance -
Rev Apr., 2016 1

2. Table of Contents
1. Overview
2. Setting authority by each Login level
3. How to program?

3. Table of Contents
1. Overview 3

4. 1. Overview Multiple administration/Installation (Ver2.0)
The sub-administrator account (Max 32 accounts) will be added.
Following 2 type of management can be provided by this account.
Site administration
Site related data, device and trunk port data,
IP device registration, isolated mode recovery,
and so on can be maintained.
Simultaneous installation
User setting, DDI table, ICD group setting can be divided and assigned to the responsible sub-administrators

5. 1. Overview Sub-Administrator account will be added from Ver2.0. Level
For
Number of Accounts
Installer
Dealers and system installers 1
User (Administrator)
On-site managers
128
Sub-Administrator
Individual site managers 32
User (User)
End users
Up to 1000 for NSX1000
Up to 2000 for NSX2000
*The total number of administrator and user accounts (Not include Sub-Administrator) combined
cannot exceed 1000 (NSX1000) / 2000 (NSX2000).

6. 1. Overview Simultaneous access (Login to Web-MC). Level Login Mode
Shared
Exclusive
Installer
Not Login
✓ (1)
User (Administrator) -
Sub-Administrator
✓ (32)
User (User)
✓ (1000/2000)
* The number in ( ) is maximum number of simultaneous login.

7. 1. Overview
There are 2 types of Login Mode for Installer as below after activate the Sub-Administrator.
Exclusive Login Mode :
Only Installer level account can login to Web-MC.
If some of Sub-Administrators already login to Web-MC, it will be disconnected.
Shared Login Mode :
Installer and Sub-Administrators can login to Web-MC at same time and program each settings
by assignment the setting authority to Sub-Administrators.
If the Installer does not login to Web-MC, a User (Administrator) and all Sub-Administrators can
Login to Web-MC.

8. 2. Setting authority by each Login level
Table of Contents
2. Setting authority by each Login level 8

9. 2. Setting authority by each Login level
Setup
(Users)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
1.User Container ✓
✓ (*1)
✓ (*2)
2.User's Device Settings
3.User's Flexible Button
1.Wired Extension
2.Portable Station
4.User's Speed Dial
5.User's CLIP ID Table
*1 : Except the user in user group which some Sub-Administrators is assigned.
*2 : Only available for the user group which assigned in “PBX Configuration - 3.Group - 2.User Group”.
Note ) Only INSTALLER (login by Exclusive mode) is possible to change setting for User (Administrator).

10. 2. Setting authority by each Login level
Setup
(Supervisors)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
1.Automatic Two-way Recording
1.Edit a Recording ✓
Read only
2.Record List
2. ICDG Management
1.Group Monitor
2.ACD Report
3.ACD Scheduled Export
4.ACD Export History

11. (Maintenance Personnel)
2. Setting authority by each Login level
Setting authority by each Login level (3).
Setup
(Maintenance Personnel)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
1.Installer Information ✓ -
2.Sub Administrator Setting
1.Accounts
2.Site Assignment

12. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
1.Configuration
1.Slot ✓
✓ (*1)
✓ (*2)
2.Portable Station
✓ (*3)
✓ (*4)
*1 : Except the site which some Sub-Administrators is assigned.
*2 : Only available for the site which assigned in “Maintenance Personnel - 2.Sub Administrator Setting - 2.Site Assignment”.
*3 : Except the Portable Station which some Sub-Administrators is assigned.
*4 : Only available for the Portable Station which assigned in “PBX Configuration - 1.Configuration - 2.Portable Station”.

13. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
1.Configuration
3.Option ✓
✓ (*1)
Read only
4.Clock Priority
5.DSP Resource
1.Setting
2.Usage
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.

14. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
2.System
1.Date & Time
1.Date & Time Settings ✓
Read only
2.SNTP / Daylight Saving
✓ (*1)
2.Operator & BGM
3.Timers & Counters
4.Week Table
5.Holiday Table
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.

15. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
2.System
6.Numbering Plan
1.Main ✓
✓ (*1)
Read only
2.Quick Dial
3.B/NA DND Call Feature
7. Class of Service
1.COS Settings
2.External Call Block
3. Internal Call Block
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.

16. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
2.System
8.Ring Tone Patterns
1.Call from CO ✓
✓ (*1)
Read only
2.Call from DOORPHONE
3.Call from Others
9.System Options
10.Extension CID Settings
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.

17. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
2.System
11.Audio Gain
1.Paging/MOH ✓
✓ (*1)
Read only
2.Card
13.Security
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.

18. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
3.Group
1.Trunk Group
1.TRG Settings ✓
✓ (*1)
Read only
2.Local Access Priority
3.Caller ID Modification
4.Dialling plan
5.Charge Rate
2.User Group
✓ (*2)
✓ (*1, 2)
✓ (*3)
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.
*2 : Except the user group which some Sub-Administrators is assigned.
*3 : Only available for the user group which assigned in “PBX Configuration - 3.Group - 2.User Group”.

19. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
3.Group
3.Call Pickup Group
1.Main Setting ✓
✓ (*1)
Read only
2.Priority Setting
4.Paging Group
1.Priority Setting
2.External Pager
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.

20. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
3.Group
5.Incoming Call Distribution Group
1.Group Settings ✓
✓ (*2)
✓ (*1, 2)
✓ (*3)
2.Queuing Time Table
✓ (*1)
Read only
3.Miscellaneous
4.ACD Supervisor
5.Member -
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.
*2 : Except the ICD group which some Sub-Administrators is assigned.
*3 : Only available for the ICD group which assigned in “PBX Configuration - 5.Incoming Call Distribution Group -
1.Group Settings - Miscellaneous”.

21. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
3.Group
6.Extension Hunting Group ✓
✓ (*1)
Read only
7.UM Group
1.System Settings
2.Unit Settings
8.PS Ring Group
9.Conference Group
10.P2P Group
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.

22. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
4.Extension
1.DSS Console ✓
✓ (*2)
✓ (*1, 2)
✓ (*3)
2.PS Single CO Appearance (*4)
✓ (*1)
Read only
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.
*2 : Except the site which some Sub-Administrators is assigned.
*3 : Only available for the site which assigned in “Maintenance Personnel - 2.Sub Administrator Setting - 2.Site Assignment”.
*4 : This setting is shown only for USA and Canada model.

23. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
5.Optional Device
1.Doorphone ✓
Read only
2.External Pager
✓ (*1)
3.Voice Message
1.DISA System
2.DISA Message
4.External Relay
5.External Sensor
6.Optional IP Device
✓ (*2)
✓ (*3)
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.
*2 : Except the user group which some Sub-Administrators is assigned.
*3 : Only available for the user group which assigned in “PBX Configuration - 3.Group - 2.User Group”.

24. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
6.Feature
1.System Speed Dial ✓
Read only
2.Hotel & Charge
✓ (*1)
3.Verification Code
4.Second Dial Tone
5.Absent Message
6.Tenant
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.

25. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
7.TRS
1.Denied Code ✓
✓ (*1)
Read only
2.Exception Code
3.Special Carrier
4.Emergency Dial
5.Miscellaneous
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.

26. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
8.ARS
1.System Setting ✓
✓ (*1)
Read only
2.Leading Number
3.Routing Plan Time
4.Rounting Plan Priority
5.Carrier
1.Main Setting
2.TRG Priority
3.Authorisation Code for Tenant
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.

27. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
8.ARS
6. Leading Number Exception ✓
✓ (*1)
Read only
7. Authorisation Code for TRG
9.Private Network
1. TIE Table
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.

28. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
10.CO & Incoming Call
1.CO Line Settings ✓
✓ (*1)
Read only
2.DIL Table & Port Settings
3.DDI/DID Table
✓ (*2)
✓ (*3)
4.MSN Table
5.Miscellaneous
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.
*2 : Except the DDI/DID table which some Sub-Administrators is assigned.
*3 : Only available for the user group which assigned in “PBX Configuration - 10.CO & Incoming Call - 3.DDI/DID Table”.

29. 2. Setting authority by each Login level
Setup
(PBX Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
11.Maintenance
1.Main ✓
✓ (*1)
Read only
2.CS Synchronisation
1.Air Synchronisation
2.LAN Synchronisation
3.LAN Sync Group Setting
3. Power Failure Transfer
（Expansion GW)
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.

30. 2. Setting authority by each Login level
Setup
(UM Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
1.Mailbox Settings ✓
✓ (*1)
Read only
2.Class of Service
3.UM Extension / Trunk Service
1.Service Group
2.Port Assignment
4.Service Settings
1.Caller ID / PIN Call Routing
2.Parameters
3.Custom Service
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.

31. 2. Setting authority by each Login level
Setup
(UM Configuration)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
5.System Parameters
1.Mailbox Group ✓
✓ (*1)
Read only
2. Extension Group
3.System Caller Name Announcement
4.Parameters
6.H/W Settings
7.System Security
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.

32. (Router Configuration (*1))
2. Setting authority by each Login level
Setting authority by each Login level (24).
Setup
(Router Configuration (*1))
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
1.Setup
1.Router Information
1.Connection Status ✓
Read only
2.PPPoE Status
2.WAN
1.Connection Settings
2.Network Monitor
3.Protocol Bridge
4.Dynamic DNS
*1 : Only for NS1000 Expansion GW

33. (Router Configuration (*1))
2. Setting authority by each Login level
Setting authority by each Login level (25).
Setup
(Router Configuration (*1))
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
1.Setup
3.LAN
1.IPv4 ✓
Read only
2.DNS Server
4.Routing
5.DMZ
6.MAC Address
7.Pass Through VPN Settings
*1 : Only for NS1000 Expansion GW

34. (Router Configuration (*1))
2. Setting authority by each Login level
Setting authority by each Login level (26).
Setup
(Router Configuration (*1))
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
2.Firewall
1.One Touch Security ✓
Read only
2.Packet Filtering
3.QoS Settings
*1 : Only for NS1000 Expansion GW

35. 2. Setting authority by each Login level
Setup
(Network Service)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
1.IP Address/ Ports ✓
Read only
2.Server Feature
1.DHCP（LAN)
2.DHCP（MNT)
3.FTP
5.HTTP, 6.NTP
7.SMTP, 8.IMAP4
9.TELNET

36. 2. Setting authority by each Login level
Setup
(Network Service)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
3.Client Feature
1.FTP ✓
Read only
2.SYSLOG
3.SNMP agent
4.Directory Service
1.Server Setting
2.External Directory
3.User Container Sync
5.HTTP
6.Remote Maintenance

37. 2. Setting authority by each Login level
Setup
(Network Service)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
4.Other
1.Security
1.Encryption ✓
Read only
2.Protection
3.Packet Filtering
2.NAS

38. 2. Setting authority by each Login level
Also Sub-Administrators support following settings under Maintenance (1).
Maintenance
(Tool)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
2.BRI Automatic Configuration (*1) ✓
✓ (*2)
✓ (*1, 2)
✓ (*3)
4.Extension List View
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.
*2 : Except the site which some Sub-Administrators is assigned.
*3 : Only available for the site which assigned in “Maintenance Personnel - 2.Sub Administrator Setting - 2.Site Assignment”.

39. 2. Setting authority by each Login level
Also Sub-Administrators support following settings under Maintenance (2).
Maintenance
(Utility)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
1.Diagnosis
1.Card Diagnosis ✓
✓ (*1)
✓ (*2)
2.Ping
2.File
2.File Transfer PBX to PC
5.Message file transfer PC to PBX
6.Message file transfer PBX to PC
*1 : Except the site which some Sub-Administrators is assigned.
*2 : Only available for the site which assigned in “Maintenance Personnel - 2.Sub Administrator Setting - 2.Site Assignment”.

40. 2. Setting authority by each Login level
Also Sub-Administrators support following settings under Maintenance (3).
Maintenance
(Utility)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
3.Log
3.Web Operation Log ✓
✓ (*1)
✓ (*2)
*1 : It is possible to save and clear the log except the site which some Sub-Administrators is assigned.
It is only possible to save the log of the site which some Sub-Administrator is assigned.
*2 : Save and clear the log are only available for the site which assigned in “Maintenance Personnel -
2.Sub Administrator Setting - 2.Site Assignment”.

41. 2. Setting authority by each Login level
Also Sub-Administrators support following settings under Maintenance (4).
Maintenance
(Utility)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
4.Monitor/Trace
1.ISDN/QSIG Protocol Trace ✓
✓ (*2)
✓ (*1, 2)
✓ (*3)
2.V-IPGW16 Protocol Trace
3.V-SIPGW16 Protocol Trace
8.T1/E1 Signaling Bit Monitor
9.T1/E1 Line Trace
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.
*2 : Except the site which some Sub-Administrators is assigned.
*3 : Only available for the site which assigned in “Maintenance Personnel - 2.Sub Administrator Setting - 2.Site Assignment”.

42. 2. Setting authority by each Login level
Also Sub-Administrators support following settings under Maintenance (5).
Maintenance
(Utility)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
5.Report
1.Digital Trunk Error Report ✓
✓ (*1)
✓ (*2)
2.IP Extension Statistical Information
5. Report
6. IP-CS Information
1.Air Sync Information
2.LAN Sync Information
*1 : Except the site which some Sub-Administrators is assigned.
*2 : Only available for the site which assigned in “Maintenance Personnel - 2.Sub Administrator Setting - 2.Site Assignment”.

43. 2. Setting authority by each Login level
Also Sub-Administrators support following settings under Maintenance (6).
Maintenance
(Utility)
Login level
INSTALLER
Administrator
Sub-Administrator
Exclusive
Shared
7. Notification
1.Alert ✓
✓ (*2)
✓ (*3)
2.System Analysis
✓ (*1, 2)
3.Test
8.Command
2.Network command
*1 : It will be possible by assign availability in “Tool - 2.Screen Customise”.
*2 : Except the site which some Sub-Administrators is assigned.
*3 : Only available for the site which assigned in “Maintenance Personnel - 2.Sub Administrator Setting - 2.Site Assignment”.

44. Table of Contents
3. How to program? 44

45. 3. How to program? Sub-Administrator Setting - Accounts (1)
Click “Maintenance Personnel
- 2.Sub Administrator Setting
- 1.Accounts”.
Select target line.
Then click “Edit”.

46. 3. How to program? Sub-Administrator Setting - Accounts (2)
Enter “Login ID” and “Password”.
Default)
Login ID : S-ADMIN001 to S-ADMIN032
Password : 0001 to 0032
Select “WebMC Language”.
Then click “OK”.

47. 3. How to program? Sub-Administrator Setting - Accounts (3)
Tick “Activated” box.
Then click “OK”.

48. 3. How to program? Sub-Administrator Setting - Site Assignment (1)
Click “Maintenance Personnel
- 2.Sub Administrator Setting
- 2.Site Assignment”.
Select Sub-Administrator for each sites.
Then click “OK”.

49. 3. How to program? Screen Customise for Sub-Administrators
Click “Tool - 2.Screen Customise”.
Select “Sub-Administrator”.

50. 3. How to program? Assign a Sub-Administrator for each User Groups
Click “PBX Configuration - 3.Group - 2.User Group”.
Select “Sub-Administrator”.

51. 3. How to program? Assign a Sub-Administrator for each ICD Groups
Click “PBX Configuration - 5.Incoming Call Distribution Group –
1.Group Settings - Miscellaneous”.
Select “Sub-Administrator”.

52. 3. How to program? Assign a Sub-Administrator for each DDI / DID Table
Click “PBX Configuration - 10.CO & Incoming Call - 3.DDI/DID Table”.
Select “Sub-Administrator”.

53. 3. How to program?
Assign a Sub-Administrator for each Portable Station
Click “PBX Configuration - 1.Configuration - 2.Portable Station”.
Select “Sub-Administrator”.

54. 3. How to program? Setup Login Mode by INSTALLER (1)
After setting of previous page, Logout from WebMC at once.
Then Login to WebMC by “INSTALLER” again.

55. 3. How to program? Setup Login Mode by INSTALLER (2)
Select “Shared Login Mode” or “Exclusive Login Mode”.
When select “Exclusive Login Mode”,
- Other Users (Administrator) and Sub-Administrators
will be log out if they log in by their accounts.
will not be able to log in by their accounts.
If some Administrators is logging in, the information which one is logging in will be displayed.

56. Table of Contents
Thank you ! The END 56

57. Modification
10.7_NSX1000_2000_Simultaneous Maintenance_Rev2.0_18Apr2016.pptx
- 1st release