1. ECET 402 Help Bcome Exceptional / snaptutorial.com

3. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 1 Homework
ECET 402  HW Week 1
Pages: 20-21: #2,4,6,11,14
CH 3pgs:103 #4,6

4. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 1 iLab
1.From Part A, step 1(b) of lab instructions, change the temperature from 0 to 30° C and record the corresponding RTD resistance in Table 1.
2.Graph the temperature-resistance characteristics of RTD below:
3.Is the graph obtained in step 2 above linear (a straight line)?
4.Use the graph obtained in step 2 above to determine the resistance of RTD at 75° F.

5. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 2 Homework
Chapter 3
Page Problems 24, 25, 28, 30, and 38

6. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 2 iLab
1.After completing Part A of week 2 lab, complete the following table:
2.Briefly describe if you had any issues with this lab.
3.Briefly describe how you would display the temperature on the LCD display of a microcontroller system.
4.From Part B, step 1 of lab instructions, paste your Multisim circuit design below.
5.From Part B, step 2 of lab instructions, paste your Multisim circuit design below.

7. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 3 Homework
Homework
1. What is the difference between static,sliding, and viscous friction?
2. An aluminum casting that weighs 10 lb is resting on a steel surface.
6.A robot arm must be able to extend 24 in. horizontally in 2 s while carrying a load of 10 lb. How much force is required, assuming the arm is accelerating all the way?

8. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 3 iLab
Part A – Voltage to Frequency Converter
1.Change input voltage from 2–10 volts and record measured frequency in Table 1
2. Use the data obtained in Table 1 to graph Frequency vs. Voltage in Figure 1.
3.Is the output frequency vs. voltage graph linear?

9. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 4 Homework
Week 4 Homework
Chapter 11: pp. 483–488, Problems 1, 2, 6, 8, 12, 13, and 19
1.Assume that Figure 11.25(a) is the response curve of a control system to a step function. Determine the following parameters: rise time, overshoot, and settling time.

10. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 4 iLab Relays and Relay Logic Controls
ECET 402 Week 4 iLab Relays and Relay Logic Controls

11. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 5 Homework
Chapter 12:
1. Draw a relay wiring diagram for a circuit that implements the simple logic diagram shown in Figure The circuit should be in the style of Figure 12.1(a).
2. Repeat Exercise 1 except draw the circuit as a ladder diagram.

12. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 5 iLab PLC Programming with LogixPro
Introduction:
The requirements for a motor with a temperature sensor are that the motor must be turned on with a Push Button switch, and also turned off with a push button switch. If at any time the temperature is too hot, the motor must turn off no matter what push buttons are pressed.

13. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 5 iLab Stepper Motor and Measuring Speed of a DC Motor
Part A
 Take a digital photo of your stepper motor circuit and paste it below:
Once the assembly of stepper motor circuit is completed and power is applied, observe the direction of rotation and record it here:

14. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 6 Homework
P.405, #1Give an example of an open-loop control system. Explain why the system is open-loop, and identify the controller and final control element.
P.405, #2Give an example of a closed-loop control system. Explain why the system is closed-loop, and identify the sensor, controller, and final control element.
P.405, #7Describe the advantages of a 4- to 20-mA current loop as an input signal compared to a 0-to 5-V input signal.
P.435, #2Complete a report on one type of open communications network.

15. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 6 iLab
1. Determine the overall transfer function of the system given below by hand as discussed in pre-lab. Please show your work and type the equations if you can
2. Determine the overall transfer function of the system shown above using MATLAB. Copy the MATLAB code and the overall transfer function obtained and paste them below:

16. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 7 iLab Root Locus Plots and the Stability of a Control System
ECET 402 Week 7 iLab Root Locus Plots and the Stability of a Control System

17. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 7 iLab
ECET 402 Week 7 iLab

18. ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 7 You Decide Assignment
ECET 402 Week 7 You Decide Assignment

20. ECET 402 Help Bcome Exceptional / snaptutorial.com